Electrical CircuitsElectrical Circuits

From current and voltage to Thevenin, transients, AC power and resonance — explained from zero, with lots of solved circuits. Current আর voltage থেকে শুরু করে Thevenin, transient, AC power আর resonance — একদম শূন্য থেকে, অনেক solved circuit সহ।

Note: This chapter is for the BUET IICT written test (MSc in ICT / MSc in Information Security). Electrical Circuits is an optional topic — you answer any 6 of 10 topics, so this can be one of your 6. It is written for someone with a CS background. We start from zero. If you can solve two equations with two unknowns, you can do everything here.
Note: এই chapter টা BUET IICT written test-এর জন্য (MSc in ICT / MSc in Information Security)। Electrical Circuits একটা optional topic — 10টা topic থেকে যেকোনো 6টা answer করতে হয়, তাই এটা তোমার 6টার একটা হতে পারে। এটা CS background-এর মানুষের জন্য লেখা। আমরা একদম শূন্য থেকে শুরু করব। দুইটা unknown-এর দুইটা equation solve করতে পারলেই এখানের সব পারবে।

1. Basic Quantities: Charge, Current, Voltage, Power1. Basic Quantities: Charge, Current, Voltage, Power

Think of a circuit like water in pipes. Charge is the water. Current is how fast the water flows. Voltage is the pressure that pushes the water. Resistance is a narrow part of the pipe that slows the flow. This picture is not perfect, but it helps a lot at the start.

Circuit-কে পাইপের পানির মতো ভাবো। Charge হলো পানি। Current হলো পানি কত দ্রুত বইছে। Voltage হলো সেই চাপ যেটা পানিকে ঠেলে দেয়। Resistance হলো পাইপের সরু অংশ, যেটা প্রবাহ কমিয়ে দেয়। এই তুলনাটা পুরোপুরি ঠিক না, কিন্তু শুরুতে অনেক কাজে দেয়।

Charge (Q)Charge (Q)

Charge is a basic property of particles. An electron has a negative charge of \(-1.602 \times 10^{-19}\) C. The unit of charge is the coulomb (C). One coulomb is the charge of about \(6.24 \times 10^{18}\) electrons. Charge can not be created or destroyed. It only moves from one place to another.

Charge হলো কণার একটা মৌলিক ধর্ম। একটা electron-এর charge হলো \(-1.602 \times 10^{-19}\) C (negative)। Charge-এর unit হলো coulomb (C)। এক coulomb মানে প্রায় \(6.24 \times 10^{18}\)টা electron-এর charge। Charge তৈরি বা ধ্বংস করা যায় না, শুধু এক জায়গা থেকে আরেক জায়গায় যায়।

Current (I)Current (I)

Current is the rate of flow of charge. It tells how many coulombs pass a point in one second. The unit is the ampere (A). 1 A = 1 C/s.

By tradition, current direction is the direction positive charge would move. Electrons actually move the opposite way. In circuit problems we always use the traditional (conventional) direction.

Current হলো charge প্রবাহের হার (rate)। এক second-এ একটা বিন্দু দিয়ে কত coulomb যায়, সেটাই current। Unit হলো ampere (A)। 1 A = 1 C/s।

নিয়ম অনুযায়ী, positive charge যেদিকে যেত, সেটাই current-এর direction। Electron আসলে উল্টো দিকে যায়। Circuit problem-এ আমরা সবসময় এই conventional direction-ই ব্যবহার করি।

\[ i = \frac{dq}{dt} \qquad\text{and for steady current}\qquad I = \frac{Q}{t} \qquad\qquad q(t) = \int_{0}^{t} i\,dt + q(0) \]
Example 1: 120 C of charge passes through a wire in 1 minute. Find the current.

t = 1 min = 60 s. So I = Q / t = 120 / 60 = 2 A.

Example 1: একটা wire দিয়ে 1 minute-এ 120 C charge যায়। Current কত?

t = 1 min = 60 s। তাই I = Q / t = 120 / 60 = 2 A।

Example 2: The charge entering an element is q(t) = 5t² mC. Find the current at t = 3 s.

i = dq/dt = d(5t²)/dt = 10t mA. At t = 3 s: i = 10 × 3 = 30 mA.

Example 2: একটা element-এ charge ঢুকছে q(t) = 5t² mC। t = 3 s-এ current কত?

i = dq/dt = d(5t²)/dt = 10t mA। t = 3 s-এ: i = 10 × 3 = 30 mA।

Voltage (V)Voltage (V)

Voltage (also called potential difference) is the energy needed to move 1 coulomb of charge from one point to another. The unit is the volt (V). 1 V = 1 J/C.

Voltage is always between two points. When we say "the voltage at node A is 5 V", we mean 5 V compared to a reference point called ground (0 V).

Voltage (যাকে potential difference-ও বলে) হলো 1 coulomb charge-কে এক বিন্দু থেকে আরেক বিন্দুতে নিতে যত energy লাগে। Unit হলো volt (V)। 1 V = 1 J/C।

Voltage সবসময় দুইটা বিন্দুর মধ্যে মাপা হয়। যখন বলি "node A-এর voltage 5 V", তখন বোঝাই ground (0 V) নামের একটা reference বিন্দুর তুলনায় 5 V।

\[ v = \frac{dw}{dq} \qquad\qquad V = \frac{W}{Q} \]

Power (P) and Energy (W)Power (P) আর Energy (W)

Power is how fast energy is used or given. The unit is the watt (W). 1 W = 1 J/s. For any element, power = voltage × current. With Ohm's law (next section) we get two more forms for a resistor.

Energy is power × time. The unit is the joule (J). Electricity bills use kWh (kilowatt-hour). 1 kWh = 1000 W × 3600 s = 3.6 × 10⁶ J.

Power হলো কত দ্রুত energy খরচ হচ্ছে বা দেওয়া হচ্ছে। Unit হলো watt (W)। 1 W = 1 J/s। যেকোনো element-এর জন্য power = voltage × current। Ohm's law (পরের section) দিয়ে resistor-এর জন্য আরও দুইটা রূপ পাই।

Energy = power × time। Unit হলো joule (J)। বিদ্যুৎ bill-এ kWh (kilowatt-hour) ব্যবহার হয়। 1 kWh = 1000 W × 3600 s = 3.6 × 10⁶ J।

\[ P = VI = I^2 R = \frac{V^2}{R} \qquad\qquad W = P\,t \qquad\qquad p = \frac{dw}{dt} = v\,i \]
Example 3: A 6 Ω resistor is connected to 12 V. Find the current and power in all three ways.

I = V/R = 12/6 = 2 A.

P = VI = 12 × 2 = 24 W.   P = I²R = 2² × 6 = 24 W.   P = V²/R = 144/6 = 24 W. All three give 24 W ✓.

Example 3: একটা 6 Ω resistor 12 V-এ লাগানো। Current আর তিনভাবে power বের করো।

I = V/R = 12/6 = 2 A।

P = VI = 12 × 2 = 24 W।   P = I²R = 2² × 6 = 24 W।   P = V²/R = 144/6 = 24 W। তিনটাই 24 W দেয় ✓।

Example 4: A 100 W bulb runs for 5 hours. Find the energy in kWh and in joules. If 1 unit (kWh) costs 8 Tk, what is the cost?

W = P × t = 100 W × 5 h = 500 Wh = 0.5 kWh.

In joules: 100 × (5 × 3600) = 1.8 × 10⁶ J = 1.8 MJ.

Cost = 0.5 × 8 = 4 Tk.

Example 4: একটা 100 W bulb 5 ঘণ্টা জ্বলে। Energy kWh আর joule-এ কত? 1 unit (kWh)-এর দাম 8 টাকা হলে খরচ কত?

W = P × t = 100 W × 5 h = 500 Wh = 0.5 kWh।

Joule-এ: 100 × (5 × 3600) = 1.8 × 10⁶ J = 1.8 MJ।

খরচ = 0.5 × 8 = 4 টাকা।

Passive sign conventionPassive sign convention

How do we know if an element takes power or gives power? We use the passive sign convention:

  • If current enters the + terminal of the element, then p = +vi. If p is positive, the element absorbs power (like a resistor or a charging battery).
  • If current enters the − terminal, then p = −vi. A negative absorbed power means the element supplies power (like a source).
  • In any circuit, total power absorbed = total power supplied. So the sum of all p (with signs) is zero. This is a great way to check your answer.

একটা element power নিচ্ছে নাকি দিচ্ছে, কীভাবে বুঝব? আমরা passive sign convention ব্যবহার করি:

  • Current যদি element-এর + terminal দিয়ে ঢোকে, তাহলে p = +vi। p positive হলে element power absorb করছে (যেমন resistor বা charge হচ্ছে এমন battery)।
  • Current যদি − terminal দিয়ে ঢোকে, তাহলে p = −vi। Absorbed power negative মানে element আসলে power supply করছে (যেমন source)।
  • যেকোনো circuit-এ মোট absorbed power = মোট supplied power। তাই sign সহ সব p-এর যোগফল শূন্য। উত্তর check করার এটা দারুণ উপায়।
element+−viCurrent enters the + terminal → p = v·i is power ABSORBEDp > 0 : absorbs (load) p < 0 : supplies (source)
Passive sign convention: current i enters the + terminal, so p = vi is the power absorbed.Passive sign convention: current i + terminal দিয়ে ঢুকছে, তাই p = vi হলো absorbed power।
Example 5: An element has 5 V across it (+ on the left). (a) 2 A enters the left (+) terminal. (b) 2 A enters the right (−) terminal. Find the power absorbed in each case.

(a) Current enters +: p = +vi = 5 × 2 = +10 W → absorbs 10 W.

(b) Current enters −: p = −vi = −(5 × 2) = −10 W → it supplies 10 W.

Example 5: একটা element-এর উপর 5 V (বাম দিকে +)। (a) 2 A বাম (+) terminal দিয়ে ঢোকে। (b) 2 A ডান (−) terminal দিয়ে ঢোকে। প্রতি ক্ষেত্রে absorbed power কত?

(a) Current + দিয়ে ঢোকে: p = +vi = 5 × 2 = +10 W → 10 W absorb করে।

(b) Current − দিয়ে ঢোকে: p = −vi = −(5 × 2) = −10 W → আসলে 10 W supply করে।

Resistance and resistivityResistance আর resistivity

Resistance (R) is how much a material opposes current. Unit: ohm (Ω). It depends on the material and the shape:

  • Longer wire → more resistance (R ∝ L).
  • Thicker wire (bigger area A) → less resistance (R ∝ 1/A).
  • Resistivity ρ (rho) is a property of the material. Copper has low ρ, so it is used in wires. Unit of ρ: Ω·m.

Conductance G = 1/R. Unit: siemens (S). It is handy in parallel circuits and nodal analysis.

Resistance (R) হলো কোনো material current-কে কতটা বাধা দেয়। Unit: ohm (Ω)। এটা material আর আকারের উপর নির্ভর করে:

  • লম্বা wire → বেশি resistance (R ∝ L)।
  • মোটা wire (বড় area A) → কম resistance (R ∝ 1/A)।
  • Resistivity ρ (rho) হলো material-এর নিজস্ব ধর্ম। Copper-এর ρ কম, তাই wire-এ copper ব্যবহার হয়। ρ-এর unit: Ω·m।

Conductance G = 1/R। Unit: siemens (S)। Parallel circuit আর nodal analysis-এ এটা কাজে লাগে।

\[ R = \frac{\rho L}{A} \qquad\qquad G = \frac{1}{R} \qquad\qquad A_{\text{circle}} = \frac{\pi d^2}{4} \]
Example 6: A copper wire is 100 m long with cross-section area 1 mm². ρ(copper) = 1.72 × 10⁻⁸ Ω·m. Find R.

First convert area: 1 mm² = 1 × 10⁻⁶ m² (because 1 mm = 10⁻³ m, so 1 mm² = 10⁻⁶ m²).

R = ρL/A = (1.72 × 10⁻⁸ × 100) / (1 × 10⁻⁶) = 1.72 × 10⁻⁶ / 10⁻⁶ = 1.72 Ω.

Example 6: একটা copper wire 100 m লম্বা, cross-section area 1 mm²। ρ(copper) = 1.72 × 10⁻⁸ Ω·m। R কত?

আগে area convert করি: 1 mm² = 1 × 10⁻⁶ m² (কারণ 1 mm = 10⁻³ m, তাই 1 mm² = 10⁻⁶ m²)।

R = ρL/A = (1.72 × 10⁻⁸ × 100) / (1 × 10⁻⁶) = 1.72 × 10⁻⁶ / 10⁻⁶ = 1.72 Ω।

Exam trick — stretched wire: If a wire is stretched to n times its length, the volume stays the same. So the area becomes A/n. New R = ρ(nL)/(A/n) = n² R. Stretch to double length → resistance becomes 4 times.
Exam trick — টেনে লম্বা করা wire: একটা wire-কে টেনে n গুণ লম্বা করলে volume একই থাকে। তাই area হয়ে যায় A/n। নতুন R = ρ(nL)/(A/n) = n² R। দ্বিগুণ লম্বা করলে resistance 4 গুণ হয়।
Real axial-lead resistors with colour bands
Real resistors. The colour bands tell the resistance value. (Image: Wikimedia Commons)বাস্তব resistor। রঙের band গুলো resistance-এর মান বলে দেয়। (Image: Wikimedia Commons)

Units tableUnits table

QuantityQuantitySymbolSymbolUnitUnitIn base termsBase unit-এ
ChargeQ, qcoulomb (C)A·s
CurrentI, iampere (A)C/s
VoltageV, vvolt (V)J/C = W/A
ResistanceRohm (Ω)V/A
ConductanceGsiemens (S)A/V = 1/Ω
PowerP, pwatt (W)J/s = V·A
EnergyWjoule (J)W·s (1 kWh = 3.6 MJ)
CapacitanceCfarad (F)C/V
InductanceLhenry (H)V·s/A
Frequencyfhertz (Hz)1/s
ResistivityρΩ·m—
PrefixPrefixp (pico)n (nano)μ (micro)m (milli)k (kilo)M (mega)G (giga)
Valueমান10⁻¹²10⁻⁹10⁻⁶10⁻³10³10⁶10⁹
Common mistake: Forgetting to convert prefixes. 4.7 kΩ = 4700 Ω, 100 μF = 100 × 10⁻⁶ F = 10⁻⁴ F, 20 mH = 0.02 H. Always convert to base units before you put numbers in a formula.
সাধারণ ভুল: Prefix convert করতে ভুলে যাওয়া। 4.7 kΩ = 4700 Ω, 100 μF = 100 × 10⁻⁶ F = 10⁻⁴ F, 20 mH = 0.02 H। Formula-তে সংখ্যা বসানোর আগে সবসময় base unit-এ convert করো।

2. Ohm's Law, KCL and KVL2. Ohm's Law, KCL আর KVL

These three laws are the tools for every circuit problem. Everything later (nodal, mesh, Thevenin) is built only on these.

First, some words:

  • Node: a point where two or more elements join. All wire connected with no element in between is the same node.
  • Branch: a single element (a resistor, a source) between two nodes.
  • Loop: any closed path in the circuit. A mesh is a loop with no other loop inside it.

এই তিনটা law হলো সব circuit problem-এর হাতিয়ার। পরে যা পড়ব (nodal, mesh, Thevenin) সব কিছু শুধু এগুলোর উপরেই দাঁড়িয়ে।

আগে কিছু শব্দ:

  • Node: যেখানে দুই বা বেশি element যুক্ত হয়। মাঝে কোনো element ছাড়া যত wire জোড়া, সব একই node।
  • Branch: দুইটা node-এর মাঝে একটা element (resistor বা source)।
  • Loop: circuit-এর যেকোনো বন্ধ পথ। যে loop-এর ভিতরে আর কোনো loop নেই, তাকে mesh বলে।

Ohm's lawOhm's law

Statement: The voltage across a resistor is directly proportional to the current through it.

Plain meaning: push harder (more V) → more current. Bigger resistor → less current for the same push.

Statement: একটা resistor-এর উপর voltage তার মধ্য দিয়ে যাওয়া current-এর সমানুপাতিক।

সহজ মানে: বেশি জোরে ঠেললে (বেশি V) → বেশি current। বড় resistor → একই ঠেলায় কম current।

\[ V = IR \qquad I = \frac{V}{R} \qquad R = \frac{V}{I} \]
Example: A 9 V battery is connected across a 450 Ω resistor. Find I.

I = V/R = 9/450 = 0.02 A = 20 mA.

Example: একটা 9 V battery একটা 450 Ω resistor-এর সাথে লাগানো। I কত?

I = V/R = 9/450 = 0.02 A = 20 mA।

Two special cases: A short circuit is R = 0 (a plain wire) — voltage across it is 0, any current can flow. An open circuit is R = ∞ (a break) — current is 0, any voltage can be across it.
দুইটা বিশেষ ক্ষেত্র: Short circuit মানে R = 0 (শুধু একটা wire) — এর উপর voltage 0, যেকোনো current যেতে পারে। Open circuit মানে R = ∞ (কাটা) — current 0, এর উপর যেকোনো voltage থাকতে পারে।

Kirchhoff's Current Law (KCL)Kirchhoff's Current Law (KCL)

Statement: The algebraic sum of currents entering a node is zero. Or: total current in = total current out.

Plain meaning: charge cannot pile up at a node. Whatever comes in must go out. Like water at a pipe joint.

Statement: একটা node-এ ঢোকা current-গুলোর algebraic যোগফল শূন্য। অথবা: মোট ঢোকা current = মোট বের হওয়া current।

সহজ মানে: Node-এ charge জমে থাকতে পারে না। যা ঢোকে, তা বের হতেই হবে। পাইপের জোড়ায় পানির মতো।

\[ \sum I_{\text{in}} = \sum I_{\text{out}} \qquad\text{or}\qquad \sum_{k} i_k = 0 \]
Example: At a node, 3 A and 5 A come in. 2 A and an unknown current I go out. Find I.

In = Out → 3 + 5 = 2 + I → I = 6 A.

If you had guessed I as "coming in", you would get I = −6 A. A negative answer just means the real direction is opposite. That is fine!

Example: একটা node-এ 3 A আর 5 A ঢোকে। 2 A আর একটা অজানা current I বের হয়। I কত?

In = Out → 3 + 5 = 2 + I → I = 6 A।

তুমি যদি I-কে "ঢুকছে" ধরতে, তাহলে I = −6 A পেতে। Negative উত্তর মানে শুধু আসল direction উল্টো। এতে কোনো সমস্যা নেই!

Kirchhoff's Voltage Law (KVL)Kirchhoff's Voltage Law (KVL)

Statement: The algebraic sum of all voltages around any closed loop is zero.

Plain meaning: if you walk around a loop and come back to the start, you are at the same "height" again. The rises (sources) must equal the drops (resistors).

Statement: যেকোনো closed loop ঘুরে সব voltage-এর algebraic যোগফল শূন্য।

সহজ মানে: একটা loop ঘুরে শুরুর জায়গায় ফিরে এলে তুমি আবার একই "উচ্চতায়" থাকো। তাই rise (source) = drop (resistor)।

\[ \sum_{\text{loop}} V = 0 \qquad\Longleftrightarrow\qquad \sum V_{\text{rise}} = \sum V_{\text{drop}} \]
KVL sign convention (use one rule and stick to it): Walk around the loop in one direction. When you go from − to + of an element, write +V (a rise). When you go from + to −, write −V (a drop). For a resistor, the side where current enters is +. So walking with the current across a resistor is a drop of IR. Most mistakes in exams come from mixing up these signs.
KVL sign convention (একটা নিয়ম নাও আর সেটাই মেনে চলো): Loop-এ এক দিকে হাঁটো। কোনো element-এর − থেকে + এ গেলে লেখো +V (rise)। + থেকে − এ গেলে লেখো −V (drop)। Resistor-এ যেদিক দিয়ে current ঢোকে সেটা +। তাই current-এর দিকে হেঁটে resistor পার হলে IR drop হয়। Exam-এ বেশিরভাগ ভুল এই sign গুলো গুলিয়ে ফেলা থেকেই আসে।
Example: A 12 V source is in a single loop with R1 = 2 Ω and R2 = 4 Ω in series. Find I, V1 and V2, and check KVL.

KVL (clockwise): +12 − 2I − 4I = 0 → 6I = 12 → I = 2 A.

V1 = 2 × 2 = 4 V, V2 = 4 × 2 = 8 V.

Check: 12 − 4 − 8 = 0 ✓. The source "rise" of 12 V is shared by the two drops.

Example: একটা loop-এ 12 V source আর series-এ R1 = 2 Ω ও R2 = 4 Ω। I, V1, V2 বের করো, আর KVL check করো।

KVL (clockwise): +12 − 2I − 4I = 0 → 6I = 12 → I = 2 A।

V1 = 2 × 2 = 4 V, V2 = 4 × 2 = 8 V।

Check: 12 − 4 − 8 = 0 ✓। Source-এর 12 V "rise" দুইটা drop-এর মধ্যে ভাগ হয়ে গেছে।

Series and parallel resistorsSeries আর parallel resistor

  • Series: one after another, the same current flows through all. Resistances simply add. Total is bigger than the biggest one.
  • Parallel: both ends connected together, the same voltage is across all. Conductances add. Total is smaller than the smallest one.
  • Two in parallel shortcut: product over sum. n equal resistors R in parallel: R/n.
  • Series: একটার পর একটা, সবার মধ্যে দিয়ে একই current যায়। Resistance সরাসরি যোগ হয়। মোট মান সবচেয়ে বড়টার চেয়েও বড়।
  • Parallel: দুই মাথা একসাথে জোড়া, সবার উপর একই voltage। Conductance যোগ হয়। মোট মান সবচেয়ে ছোটটার চেয়েও ছোট।
  • দুইটা parallel-এর shortcut: গুণফল ভাগ যোগফল (product over sum)। n টা সমান R parallel-এ: R/n।
\[ R_{\text{series}} = R_1 + R_2 + \cdots + R_n \qquad \frac{1}{R_{\text{par}}} = \frac{1}{R_1} + \frac{1}{R_2} + \cdots + \frac{1}{R_n} \qquad R_1 \parallel R_2 = \frac{R_1 R_2}{R_1 + R_2} \]
Example: (a) 10, 20, 30 Ω in series. (b) 6 Ω ∥ 3 Ω. (c) 12, 6, 4 Ω in parallel.

(a) 10 + 20 + 30 = 60 Ω.

(b) (6 × 3)/(6 + 3) = 18/9 = 2 Ω.

(c) 1/R = 1/12 + 1/6 + 1/4 = 1/12 + 2/12 + 3/12 = 6/12 → R = 2 Ω.

Example: (a) 10, 20, 30 Ω series-এ। (b) 6 Ω ∥ 3 Ω। (c) 12, 6, 4 Ω parallel-এ।

(a) 10 + 20 + 30 = 60 Ω।

(b) (6 × 3)/(6 + 3) = 18/9 = 2 Ω।

(c) 1/R = 1/12 + 1/6 + 1/4 = 1/12 + 2/12 + 3/12 = 6/12 → R = 2 Ω।

+−24 VR1 = 4 Ω6 Ω12 ΩI = 3 A2 A1 A
A series–parallel circuit: 4 Ω in series with (6 Ω ∥ 12 Ω), fed by 24 V.একটা series–parallel circuit: 24 V source, 4 Ω-এর সাথে series-এ (6 Ω ∥ 12 Ω)।
Example (the circuit above): Find the total current and the current in each resistor.

Step 1 — combine the parallel part: 6 ∥ 12 = 72/18 = 4 Ω.

Step 2 — total: Req = 4 + 4 = 8 Ω.

Step 3 — total current: I = 24/8 = 3 A (this flows through the 4 Ω).

Step 4 — voltage across the 4 Ω: 3 × 4 = 12 V. Voltage left for the parallel part: 24 − 12 = 12 V.

Step 5 — branch currents: I6 = 12/6 = 2 A, I12 = 12/12 = 1 A. Check KCL: 2 + 1 = 3 ✓.

Example (উপরের circuit): মোট current আর প্রতিটা resistor-এর current বের করো।

Step 1 — parallel অংশ একসাথে: 6 ∥ 12 = 72/18 = 4 Ω।

Step 2 — মোট: Req = 4 + 4 = 8 Ω।

Step 3 — মোট current: I = 24/8 = 3 A (এটা 4 Ω দিয়ে যায়)।

Step 4 — 4 Ω-এর উপর voltage: 3 × 4 = 12 V। Parallel অংশের জন্য বাকি থাকে: 24 − 12 = 12 V।

Step 5 — branch current: I6 = 12/6 = 2 A, I12 = 12/12 = 1 A। KCL check: 2 + 1 = 3 ✓।

Voltage divider and current dividerVoltage divider আর current divider

Voltage divider (resistors in series): the source voltage is shared in proportion to the resistances. The bigger resistor gets the bigger share.

Current divider (two resistors in parallel): the current is shared in the opposite way. The smaller resistor gets the bigger current. Notice the formula uses the other resistor on top.

Voltage divider (series-এ resistor): source voltage resistance-এর অনুপাতে ভাগ হয়। বড় resistor বড় ভাগ পায়।

Current divider (parallel-এ দুইটা resistor): current ভাগ হয় উল্টোভাবে। ছোট resistor পায় বেশি current। খেয়াল করো, formula-র উপরে থাকে অন্য resistor-টা।

\[ V_1 = V_s\,\frac{R_1}{R_1 + R_2} \qquad V_2 = V_s\,\frac{R_2}{R_1 + R_2} \qquad\qquad I_1 = I\,\frac{R_2}{R_1 + R_2} \qquad I_2 = I\,\frac{R_1}{R_1 + R_2} \]
Example (voltage divider): Vs = 15 V, R1 = 2 kΩ, R2 = 3 kΩ in series. Find V2.

V2 = 15 × 3/(2 + 3) = 15 × 0.6 = 9 V. And V1 = 15 × 2/5 = 6 V. Check: 6 + 9 = 15 ✓.

Example (voltage divider): Vs = 15 V, R1 = 2 kΩ আর R2 = 3 kΩ series-এ। V2 কত?

V2 = 15 × 3/(2 + 3) = 15 × 0.6 = 9 V। আর V1 = 15 × 2/5 = 6 V। Check: 6 + 9 = 15 ✓।

Example (current divider): 6 A enters a pair of parallel resistors 3 Ω and 6 Ω. Find each current.

I3Ω = 6 × 6/(3 + 6) = 36/9 = 4 A.   I6Ω = 6 × 3/9 = 2 A.

The smaller resistor (3 Ω) takes more current ✓. Check: both have the same voltage: 4 × 3 = 12 V and 2 × 6 = 12 V ✓.

Example (current divider): 6 A একজোড়া parallel resistor 3 Ω আর 6 Ω-এ ঢোকে। প্রতিটার current কত?

I3Ω = 6 × 6/(3 + 6) = 36/9 = 4 A।   I6Ω = 6 × 3/9 = 2 A।

ছোট resistor (3 Ω) বেশি current নেয় ✓। Check: দুইটার উপর একই voltage: 4 × 3 = 12 V আর 2 × 6 = 12 V ✓।

Loading effect: The voltage divider formula works only if nothing else draws current from the middle point. If you connect a load RL across R2, first replace R2 by (R2 ∥ RL), then use the formula. The output voltage will drop. (See practice Q11.)
Loading effect: Voltage divider formula তখনই কাজ করে যখন মাঝের বিন্দু থেকে আর কেউ current নেয় না। R2-এর উপর একটা load RL লাগালে আগে R2-কে (R2 ∥ RL) দিয়ে বদলাও, তারপর formula বসাও। Output voltage কমে যাবে। (Practice Q11 দেখো।)

Delta–wye (Δ–Y) conversionDelta–wye (Δ–Y) conversion

Some networks are neither series nor parallel (for example, a bridge). Then we convert a triangle (delta, Δ) of resistors into a star (wye, Y), or the reverse. After that, series/parallel rules work again.

কিছু network series-ও না, parallel-ও না (যেমন bridge)। তখন resistor-এর ত্রিভুজ (delta, Δ) কে তারা (wye, Y)-তে convert করি, বা উল্টোটা। তারপর আবার series/parallel নিয়ম কাজ করে।

abcRcaRbcRabDelta (Δ)abcRaRbRcWye (Y) / Star
A Δ network (left) and its equivalent Y network (right) between the same three terminals a, b, c.একই তিনটা terminal a, b, c-এর মাঝে একটা Δ network (বামে) আর তার equivalent Y network (ডানে)।
\[ \Delta \to Y:\quad R_a = \frac{R_{ab} R_{ca}}{R_{ab}+R_{bc}+R_{ca}},\quad R_b = \frac{R_{ab} R_{bc}}{R_{ab}+R_{bc}+R_{ca}},\quad R_c = \frac{R_{bc} R_{ca}}{R_{ab}+R_{bc}+R_{ca}} \] \[ Y \to \Delta:\quad R_{ab} = \frac{R_a R_b + R_b R_c + R_c R_a}{R_c},\quad R_{bc} = \frac{R_a R_b + R_b R_c + R_c R_a}{R_a},\quad R_{ca} = \frac{R_a R_b + R_b R_c + R_c R_a}{R_b} \]

Easy way to remember:

  • Δ → Y: Y arm at a node = (product of the two Δ sides touching that node) / (sum of all three Δ sides).
  • Y → Δ: Δ side = (sum of pair products of Y) / (the Y arm on the opposite node).
  • All equal: RY = RΔ/3, and RΔ = 3RY.

মনে রাখার সহজ উপায়:

  • Δ → Y: কোনো node-এর Y arm = (ওই node ছুঁয়ে থাকা দুইটা Δ side-এর গুণফল) / (তিনটা Δ side-এর যোগফল)।
  • Y → Δ: Δ side = (Y-এর জোড়ায় জোড়ায় গুণফলের যোগফল) / (উল্টো দিকের node-এর Y arm)।
  • সব সমান হলে: RY = RΔ/3, আর RΔ = 3RY।
Example: Convert the Δ with Rab = 10 Ω, Rbc = 20 Ω, Rca = 30 Ω into Y. Then convert back to check.

Sum = 10 + 20 + 30 = 60 Ω.

Ra = (10 × 30)/60 = 5 Ω, Rb = (10 × 20)/60 = 3.33 Ω, Rc = (20 × 30)/60 = 10 Ω.

Check back: pair-product sum = 5 × 3.33 + 3.33 × 10 + 10 × 5 = 16.67 + 33.33 + 50 = 100.

Rab = 100/Rc = 100/10 = 10 ✓, Rbc = 100/Ra = 100/5 = 20 ✓, Rca = 100/Rb = 100/3.33 = 30 ✓.

Special case: a Δ of three 30 Ω → a Y of three 10 Ω.

Example: Rab = 10 Ω, Rbc = 20 Ω, Rca = 30 Ω-এর Δ-কে Y-তে convert করো। তারপর উল্টো convert করে check করো।

যোগফল = 10 + 20 + 30 = 60 Ω।

Ra = (10 × 30)/60 = 5 Ω, Rb = (10 × 20)/60 = 3.33 Ω, Rc = (20 × 30)/60 = 10 Ω।

উল্টো check: জোড়া-গুণফলের যোগ = 5 × 3.33 + 3.33 × 10 + 10 × 5 = 16.67 + 33.33 + 50 = 100।

Rab = 100/Rc = 100/10 = 10 ✓, Rbc = 100/Ra = 100/5 = 20 ✓, Rca = 100/Rb = 100/3.33 = 30 ✓।

বিশেষ ক্ষেত্র: তিনটা 30 Ω-এর Δ → তিনটা 10 Ω-এর Y।

Wheatstone bridgeWheatstone bridge

A Wheatstone bridge is four resistors in a diamond, with a galvanometer G (a current meter) across the middle. It is used to measure an unknown resistance X very accurately.

The bridge is balanced when no current flows through G. That happens when points C and D are at the same voltage. Then the ratio of the upper arms equals the ratio of the lower arms.

Wheatstone bridge হলো diamond আকারে চারটা resistor, মাঝখানে একটা galvanometer G (current মাপার যন্ত্র)। অজানা resistance X খুব নির্ভুলভাবে মাপতে এটা ব্যবহার হয়।

G দিয়ে কোনো current না গেলে bridge-টা balanced। এটা হয় যখন C আর D বিন্দুর voltage সমান। তখন উপরের দুই arm-এর অনুপাত = নিচের দুই arm-এর অনুপাত।

P (R1)Q (R2)R (R3)X (R4)GACDB+−batteryBalanced whenP / Q = R / X→ no current in G
Wheatstone bridge. At balance, VC = VD and the galvanometer reads zero.Wheatstone bridge। Balance অবস্থায় VC = VD, galvanometer শূন্য দেখায়।
\[ \text{Balance:}\quad \frac{P}{Q} = \frac{R}{X} \quad\Longleftrightarrow\quad P\,X = Q\,R \quad\Longrightarrow\quad X = \frac{Q\,R}{P} \]

Why? The top path is a voltage divider: VC = V·Q/(P+Q) (measured from B). The bottom path: VD = V·X/(R+X). Set them equal → Q/(P+Q) = X/(R+X) → Q(R+X) = X(P+Q) → QR = PX.

কেন? উপরের পথটা একটা voltage divider: VC = V·Q/(P+Q) (B থেকে মেপে)। নিচের পথ: VD = V·X/(R+X)। দুইটা সমান করলে → Q/(P+Q) = X/(R+X) → Q(R+X) = X(P+Q) → QR = PX।

Example: A bridge balances with P = 100 Ω, Q = 200 Ω, R = 150 Ω. Find X.

X = QR/P = (200 × 150)/100 = 300 Ω. Check: P/Q = 0.5 and R/X = 150/300 = 0.5 ✓.

Example: P = 100 Ω, Q = 200 Ω, R = 150 Ω দিয়ে একটা bridge balanced। X কত?

X = QR/P = (200 × 150)/100 = 300 Ω। Check: P/Q = 0.5 আর R/X = 150/300 = 0.5 ✓।

Exam shortcut: If a bridge is balanced, the middle resistor (or G) carries no current. You can simply remove it (or short it — both give the same answer). Then Req = (P + Q) ∥ (R + X). If it is not balanced, use Δ–Y or nodal analysis (see practice Q13).
Exam shortcut: Bridge balanced হলে মাঝের resistor (বা G) দিয়ে কোনো current যায় না। তাই এটাকে সরাসরি সরিয়ে দিতে পারো (বা short করতে পারো — দুইভাবেই একই উত্তর)। তখন Req = (P + Q) ∥ (R + X)। Balanced না হলে Δ–Y বা nodal analysis লাগবে (practice Q13 দেখো)।

3. Nodal and Mesh Analysis3. Nodal আর Mesh Analysis

Series–parallel tricks work only for simple circuits. For bigger circuits we need a system. There are two standard systems:

  • Nodal analysis — unknowns are node voltages. Uses KCL at each node.
  • Mesh analysis — unknowns are mesh currents. Uses KVL around each mesh.

Both give a set of linear equations. For the exam, it is usually a 2×2 system. As a CS person, you already know how to solve it (substitution or Cramer's rule).

Series–parallel কৌশল শুধু সহজ circuit-এ কাজ করে। বড় circuit-এর জন্য একটা system লাগে। দুইটা standard system আছে:

  • Nodal analysis — unknown হলো node voltage। প্রতিটা node-এ KCL ব্যবহার হয়।
  • Mesh analysis — unknown হলো mesh current। প্রতিটা mesh ঘুরে KVL ব্যবহার হয়।

দুইটাতেই কিছু linear equation পাই। Exam-এ সাধারণত 2×2 system আসে। CS-এর মানুষ হিসেবে তুমি এটা solve করতে জানো (substitution বা Cramer's rule)।

\[ \begin{cases} a x + b y = e \\ c x + d y = f \end{cases} \quad\Longrightarrow\quad \Delta = ad - bc,\qquad x = \frac{ed - bf}{\Delta},\qquad y = \frac{af - ce}{\Delta} \]

Nodal analysis — step by stepNodal analysis — ধাপে ধাপে

  1. Pick one node as the reference (ground, 0 V). Usually the bottom node with the most connections.
  2. Name the other node voltages: V1, V2, ... These are your unknowns.
  3. At each unknown node, write KCL. Easy rule: sum of currents leaving through resistors = sum of source currents entering. A current leaving through a resistor from node a to node b is (Va − Vb)/R.
  4. Solve the equations. Then find any branch current with Ohm's law.
  1. একটা node-কে reference (ground, 0 V) ধরো। সাধারণত নিচের যে node-এ সবচেয়ে বেশি connection।
  2. বাকি node-গুলোর voltage-এর নাম দাও: V1, V2, ... এগুলোই unknown।
  3. প্রতিটা unknown node-এ KCL লেখো। সহজ নিয়ম: resistor দিয়ে বের হওয়া current-এর যোগফল = source থেকে ঢোকা current-এর যোগফল। Node a থেকে node b-তে resistor দিয়ে বের হওয়া current = (Va − Vb)/R।
  4. Equation solve করো। তারপর Ohm's law দিয়ে যেকোনো branch current বের করো।
+−10 VR1 = 2 ΩR2 = 4 ΩR3 = 6 ΩR4 = 2 Ω1 AV1V2reference (0 V)
Nodal example: two unknown nodes V1 and V2. The bottom wire is the reference (0 V).Nodal example: দুইটা unknown node V1 আর V2। নিচের wire হলো reference (0 V)।
Worked nodal example: In the circuit above, find V1, V2 and all branch currents.

Step 1 — KCL at node 1 (all currents leaving through resistors = 0, since no current source touches node 1):

\[ \frac{V_1 - 10}{2} + \frac{V_1}{4} + \frac{V_1 - V_2}{6} = 0 \]

Multiply by 12 (the LCM): 6(V1 − 10) + 3V1 + 2(V1 − V2) = 0 → 6V1 − 60 + 3V1 + 2V1 − 2V2 = 0 →

\[ 11V_1 - 2V_2 = 60 \quad\text{...(1)} \]

Step 2 — KCL at node 2 (currents leaving through resistors = 1 A entering from the source):

\[ \frac{V_2 - V_1}{6} + \frac{V_2}{2} = 1 \]

Multiply by 6: V2 − V1 + 3V2 = 6 →

\[ -V_1 + 4V_2 = 6 \quad\text{...(2)} \]

Step 3 — solve. From (2): V1 = 4V2 − 6. Put in (1): 11(4V2 − 6) − 2V2 = 60 → 44V2 − 66 − 2V2 = 60 → 42V2 = 126 → V2 = 3 V. Then V1 = 4(3) − 6 = 6 V.

With Cramer: Δ = 11·4 − (−2)(−1) = 44 − 2 = 42. V1 = (60·4 − (−2)·6)/42 = 252/42 = 6 ✓. V2 = (11·6 − (−1)·60)/42 = 126/42 = 3 ✓.

Step 4 — branch currents:

  • R1 (2 Ω): (10 − 6)/2 = 2 A (from the source into node 1)
  • R2 (4 Ω): 6/4 = 1.5 A (down)
  • R3 (6 Ω): (6 − 3)/6 = 0.5 A (node 1 → node 2)
  • R4 (2 Ω): 3/2 = 1.5 A (down)

Check: Node 1: 2 = 1.5 + 0.5 ✓. Node 2: 0.5 + 1 = 1.5 ✓. Power: sources give 10×2 + 3×1 = 23 W; resistors take 8 + 9 + 1.5 + 4.5 = 23 W ✓.

Worked nodal example: উপরের circuit-এ V1, V2 আর সব branch current বের করো।

Step 1 — node 1-এ KCL (resistor দিয়ে বের হওয়া সব current = 0, কারণ node 1-এ কোনো current source নেই):

\[ \frac{V_1 - 10}{2} + \frac{V_1}{4} + \frac{V_1 - V_2}{6} = 0 \]

12 (LCM) দিয়ে গুণ করি: 6(V1 − 10) + 3V1 + 2(V1 − V2) = 0 → 6V1 − 60 + 3V1 + 2V1 − 2V2 = 0 →

\[ 11V_1 - 2V_2 = 60 \quad\text{...(1)} \]

Step 2 — node 2-এ KCL (resistor দিয়ে বের হওয়া current = source থেকে ঢোকা 1 A):

\[ \frac{V_2 - V_1}{6} + \frac{V_2}{2} = 1 \]

6 দিয়ে গুণ: V2 − V1 + 3V2 = 6 →

\[ -V_1 + 4V_2 = 6 \quad\text{...(2)} \]

Step 3 — solve। (2) থেকে: V1 = 4V2 − 6। (1)-এ বসাই: 11(4V2 − 6) − 2V2 = 60 → 44V2 − 66 − 2V2 = 60 → 42V2 = 126 → V2 = 3 V। তাহলে V1 = 4(3) − 6 = 6 V।

Cramer দিয়ে: Δ = 11·4 − (−2)(−1) = 44 − 2 = 42। V1 = (60·4 − (−2)·6)/42 = 252/42 = 6 ✓। V2 = (11·6 − (−1)·60)/42 = 126/42 = 3 ✓।

Step 4 — branch current:

  • R1 (2 Ω): (10 − 6)/2 = 2 A (source থেকে node 1-এ)
  • R2 (4 Ω): 6/4 = 1.5 A (নিচের দিকে)
  • R3 (6 Ω): (6 − 3)/6 = 0.5 A (node 1 → node 2)
  • R4 (2 Ω): 3/2 = 1.5 A (নিচের দিকে)

Check: Node 1: 2 = 1.5 + 0.5 ✓। Node 2: 0.5 + 1 = 1.5 ✓। Power: source দেয় 10×2 + 3×1 = 23 W; resistor নেয় 8 + 9 + 1.5 + 4.5 = 23 W ✓।

Mesh analysis — step by stepMesh analysis — ধাপে ধাপে

  1. Find the meshes (the "windows" of the circuit). Give each one a clockwise mesh current: I1, I2, ...
  2. A resistor shared by two meshes carries the difference of the two mesh currents.
  3. Write KVL for each mesh, walking in the direction of its own mesh current. Resistor drop in mesh k = R × (Ik − Iother).
  4. Solve. Real branch current in a shared resistor = I1 − I2 (in I1's direction).

Quick-write rule (for circuits with only voltage sources): for mesh k, (sum of all R in mesh k)·Ik − (shared R)·Iother = (sum of source rises in the direction of Ik).

  1. Mesh গুলো খুঁজে বের করো (circuit-এর "জানালা" গুলো)। প্রতিটাতে একটা clockwise mesh current দাও: I1, I2, ...
  2. দুই mesh-এর shared resistor দিয়ে দুইটা mesh current-এর পার্থক্য যায়।
  3. প্রতিটা mesh-এর জন্য KVL লেখো, নিজের mesh current-এর দিকে হেঁটে। Mesh k-তে resistor drop = R × (Ik − Iঅন্যটা)।
  4. Solve করো। Shared resistor-এ আসল branch current = I1 − I2 (I1-এর দিকে)।

দ্রুত লেখার নিয়ম (শুধু voltage source থাকলে): mesh k-এর জন্য, (mesh k-এর সব R-এর যোগ)·Ik − (shared R)·Iঅন্যটা = (Ik-এর দিকে source rise-এর যোগ)।

+−24 VR1 = 4 ΩR3 = 6 ΩR2 = 2 Ω+−10 VI1I2
Mesh example: two meshes with clockwise currents I1 and I2. R3 is shared.Mesh example: দুইটা mesh, clockwise current I1 আর I2। R3 দুইজনের shared।
Worked mesh example: In the circuit above, find I1, I2, the current in R3 and the power of each source.

Mesh 1 (clockwise, start at bottom-left): go up through 24 V from − to + → +24. Through R1 → −4I1. Down through R3 → −6(I1 − I2).

\[ 24 - 4I_1 - 6(I_1 - I_2) = 0 \;\Rightarrow\; 10I_1 - 6I_2 = 24 \quad\text{...(1)} \]

Mesh 2 (clockwise): up through R3 → −6(I2 − I1). Through R2 → −2I2. Down through the 10 V source from + to − → −10.

\[ -6(I_2 - I_1) - 2I_2 - 10 = 0 \;\Rightarrow\; -6I_1 + 8I_2 = -10 \quad\text{...(2)} \]

Solve (Cramer): Δ = 10·8 − (−6)(−6) = 80 − 36 = 44.

I1 = (24·8 − (−6)(−10))/44 = (192 − 60)/44 = 132/44 = 3 A.

I2 = (10·(−10) − (−6)·24)/44 = (−100 + 144)/44 = 44/44 = 1 A.

Current in R3 = I1 − I2 = 3 − 1 = 2 A downward. Voltage across R3 = 2 × 6 = 12 V.

Powers: 24 V source: current 3 A leaves its + terminal → supplies 72 W. 10 V source: I2 = 1 A goes down and enters its + terminal → absorbs 10 W (it is being charged). Resistors: 4·3² + 2·1² + 6·2² = 36 + 2 + 24 = 62 W. Check: 72 = 62 + 10 ✓.

Cross-check with nodal: Only one unknown node (top middle, V). (V − 24)/4 + V/6 + (V − 10)/2 = 0 → ×12: 3V − 72 + 2V + 6V − 60 = 0 → V = 12 V ✓ (same 12 V across R3).

Worked mesh example: উপরের circuit-এ I1, I2, R3-এর current আর প্রতিটা source-এর power বের করো।

Mesh 1 (clockwise, নিচের-বাম থেকে শুরু): 24 V-এর − থেকে + এ উপরে উঠি → +24। R1 পার → −4I1। R3 দিয়ে নিচে → −6(I1 − I2)।

\[ 24 - 4I_1 - 6(I_1 - I_2) = 0 \;\Rightarrow\; 10I_1 - 6I_2 = 24 \quad\text{...(1)} \]

Mesh 2 (clockwise): R3 দিয়ে উপরে → −6(I2 − I1)। R2 পার → −2I2। 10 V source-এর + থেকে − এ নিচে → −10।

\[ -6(I_2 - I_1) - 2I_2 - 10 = 0 \;\Rightarrow\; -6I_1 + 8I_2 = -10 \quad\text{...(2)} \]

Solve (Cramer): Δ = 10·8 − (−6)(−6) = 80 − 36 = 44।

I1 = (24·8 − (−6)(−10))/44 = (192 − 60)/44 = 132/44 = 3 A।

I2 = (10·(−10) − (−6)·24)/44 = (−100 + 144)/44 = 44/44 = 1 A।

R3-এর current = I1 − I2 = 3 − 1 = 2 A নিচের দিকে। R3-এর উপর voltage = 2 × 6 = 12 V।

Power: 24 V source: 3 A এর + terminal দিয়ে বের হয় → 72 W supply করে। 10 V source: I2 = 1 A নিচে নেমে এর + terminal দিয়ে ঢোকে → 10 W absorb করে (এটা charge হচ্ছে)। Resistor: 4·3² + 2·1² + 6·2² = 36 + 2 + 24 = 62 W। Check: 72 = 62 + 10 ✓।

Nodal দিয়ে cross-check: এখানে unknown node একটাই (উপরের মাঝখানে, V)। (V − 24)/4 + V/6 + (V − 10)/2 = 0 → ×12: 3V − 72 + 2V + 6V − 60 = 0 → V = 12 V ✓ (R3-এর উপর একই 12 V)।

Supernode and supermesh (one-liners)Supernode আর supermesh (এক লাইনে)

  • Supernode: if a voltage source sits between two non-reference nodes, draw a bubble around both nodes and the source. Write one KCL for the whole bubble, plus one extra equation: Va − Vb = Vsource.
  • Supermesh: if a current source sits in a branch shared by two meshes, skip that branch and write one KVL around the big outer loop of both meshes, plus one extra equation: I1 − I2 = Isource (with the right sign).
  • Which to choose? Fewer nodes than meshes → nodal. Fewer meshes → mesh. Many current sources → nodal is easier. Many voltage sources → mesh is easier.
  • A voltage source from a node straight to ground just fixes that node's voltage — no equation needed there. A current source alone on an outer branch just fixes that mesh current.
  • Supernode: যদি একটা voltage source দুইটা non-reference node-এর মাঝে থাকে, দুই node আর source ঘিরে একটা বৃত্ত আঁকো। পুরো বৃত্তের জন্য একটা KCL লেখো, আর একটা বাড়তি equation: Va − Vb = Vsource।
  • Supermesh: যদি একটা current source দুই mesh-এর shared branch-এ থাকে, ওই branch বাদ দিয়ে দুই mesh-এর বড় বাইরের loop ঘুরে একটা KVL লেখো, আর একটা বাড়তি equation: I1 − I2 = Isource (ঠিক sign সহ)।
  • কোনটা নেব? Mesh-এর চেয়ে node কম → nodal। Mesh কম → mesh। Current source বেশি → nodal সহজ। Voltage source বেশি → mesh সহজ।
  • কোনো node থেকে সরাসরি ground পর্যন্ত voltage source থাকলে ওই node-এর voltage জানা — সেখানে equation লাগে না। বাইরের branch-এ একা current source থাকলে ওই mesh current জানা।
Exam tip: Always do a final check — KCL at one node, or a power balance. It takes 30 seconds and catches sign mistakes. In a written exam, clearly write "Applying KCL at node 1:" before each equation. Examiners give marks for the method.
Exam tip: শেষে সবসময় একটা check করো — একটা node-এ KCL, বা power balance। 30 second লাগে, কিন্তু sign-এর ভুল ধরে ফেলে। Written exam-এ প্রতিটা equation-এর আগে পরিষ্কার লেখো "Applying KCL at node 1:"। Examiner method-এর জন্যও নম্বর দেন।

4. Network Theorems4. Network Theorems

Network theorems are shortcuts. They let us simplify a big circuit before we solve it. They work for linear circuits (resistors, linear sources, and later L and C).

Network theorem গুলো হলো shortcut। বড় circuit solve করার আগে এগুলো দিয়ে সেটাকে ছোট করা যায়। এগুলো linear circuit-এ কাজ করে (resistor, linear source, আর পরে L ও C)।

Source transformationSource transformation

A voltage source Vs in series with R is the same (from outside) as a current source Is = Vs/R in parallel with the same R. You can swap them anytime. Keep the arrow of the current source pointing toward the + side of the voltage source.

একটা voltage source Vs আর তার সাথে series-এ R, বাইরে থেকে একদম একই রকম একটা current source Is = Vs/R আর তার সাথে parallel-এ একই R। যেকোনো সময় এদের অদলবদল করা যায়। Current source-এর arrow voltage source-এর + দিকের দিকে রাখো।

\[ V_s \text{ in series with } R \;\Longleftrightarrow\; I_s = \frac{V_s}{R} \text{ in parallel with } R \]
Example: 12 V in series with 3 Ω → current source 12/3 = 4 A in parallel with 3 Ω. Going back: 4 A ∥ 3 Ω → 4 × 3 = 12 V in series with 3 Ω ✓.
Example: 12 V-এর সাথে series-এ 3 Ω → 12/3 = 4 A current source, parallel-এ 3 Ω। উল্টো দিকে: 4 A ∥ 3 Ω → 4 × 3 = 12 V, series-এ 3 Ω ✓।

Superposition theoremSuperposition theorem

Statement: In a linear circuit with many independent sources, any voltage or current = the sum of the answers from each source acting alone.

How to "turn off" a source:

  • Voltage source → replace with a short circuit (0 V = plain wire).
  • Current source → replace with an open circuit (0 A = a break).
  • Dependent sources are never turned off.

Statement: অনেকগুলো independent source-ওয়ালা linear circuit-এ, যেকোনো voltage বা current = প্রতিটা source একা কাজ করলে যে উত্তর আসে, তাদের যোগফল।

একটা source "বন্ধ" করার নিয়ম:

  • Voltage source → short circuit দিয়ে বদলাও (0 V = শুধু wire)।
  • Current source → open circuit দিয়ে বদলাও (0 A = কাটা)।
  • Dependent source কখনোই বন্ধ করা হয় না।
+−12 VR1 = 4 ΩR2 = 12 Ω3 AVx
Superposition example: a 12 V source and a 3 A source both feed node Vx.Superposition example: 12 V source আর 3 A source দুইটাই node Vx-এ যুক্ত।
Worked example: In the circuit above, find Vx and the current in R2 using superposition.

Case 1 — only 12 V (3 A source → open): R1 and R2 are a simple voltage divider.

Vx′ = 12 × 12/(4 + 12) = 12 × 0.75 = 9 V.

Case 2 — only 3 A (12 V source → short): now R1 goes from Vx to ground, so R1 ∥ R2 = (4 × 12)/16 = 3 Ω. All 3 A flows into this 3 Ω.

Vx″ = 3 A × 3 Ω = 9 V.

Total: Vx = 9 + 9 = 18 V. Current in R2 = 18/12 = 1.5 A.

Check with source transformation: 12 V + 4 Ω → 3 A ∥ 4 Ω. Now two 3 A sources feed (4 ∥ 12) = 3 Ω. Vx = (3 + 3) × 3 = 18 V ✓.

Check with nodal: (Vx − 12)/4 + Vx/12 = 3 → ×12: 3Vx − 36 + Vx = 36 → Vx = 18 V ✓.

Worked example: উপরের circuit-এ superposition দিয়ে Vx আর R2-এর current বের করো।

Case 1 — শুধু 12 V (3 A source → open): R1 আর R2 একটা সাধারণ voltage divider।

Vx′ = 12 × 12/(4 + 12) = 12 × 0.75 = 9 V।

Case 2 — শুধু 3 A (12 V source → short): এখন R1 যায় Vx থেকে ground-এ, তাই R1 ∥ R2 = (4 × 12)/16 = 3 Ω। পুরো 3 A এই 3 Ω-তে যায়।

Vx″ = 3 A × 3 Ω = 9 V।

মোট: Vx = 9 + 9 = 18 V। R2-এর current = 18/12 = 1.5 A।

Source transformation দিয়ে check: 12 V + 4 Ω → 3 A ∥ 4 Ω। এখন দুইটা 3 A source (4 ∥ 12) = 3 Ω-তে যায়। Vx = (3 + 3) × 3 = 18 V ✓।

Nodal দিয়ে check: (Vx − 12)/4 + Vx/12 = 3 → ×12: 3Vx − 36 + Vx = 36 → Vx = 18 V ✓।

Trap: Superposition works for voltage and current, but NOT for power (power is I²R, not linear). Above: P from case 1 alone = 9²/12 = 6.75 W, case 2 alone = 6.75 W, sum = 13.5 W. But the true power in R2 = 18²/12 = 27 W. Always add V or I first, then find power.
ফাঁদ: Superposition voltage আর current-এর জন্য কাজ করে, কিন্তু power-এর জন্য না (power হলো I²R, linear না)। উপরে: শুধু case 1-এ P = 9²/12 = 6.75 W, শুধু case 2-এ = 6.75 W, যোগ = 13.5 W। কিন্তু R2-এর আসল power = 18²/12 = 27 W। আগে V বা I যোগ করো, তারপর power বের করো।

Thevenin's theoremThevenin's theorem

Statement: Any linear circuit, seen from two terminals a–b, can be replaced by one voltage source Vth in series with one resistor Rth.

Why it is useful: When the load changes (try RL = 2, 5, 10 Ω...), you do not need to solve the full circuit again. Just use IL = Vth/(Rth + RL).

Steps:

  1. Remove the load. Mark terminals a and b.
  2. Vth = the open-circuit voltage between a and b (Voc).
  3. Rth = the resistance seen from a–b after killing all independent sources (voltage source → short, current source → open).
  4. Put the load back on the equivalent circuit.

Statement: যেকোনো linear circuit-কে দুইটা terminal a–b থেকে দেখলে, সেটাকে একটা voltage source Vth আর তার সাথে series-এ একটা resistor Rth দিয়ে বদলানো যায়।

কেন কাজের: Load বদলালে (RL = 2, 5, 10 Ω... দিয়ে চেষ্টা করো), পুরো circuit আবার solve করতে হয় না। শুধু IL = Vth/(Rth + RL)।

ধাপ:

  1. Load সরিয়ে ফেলো। Terminal a আর b চিহ্নিত করো।
  2. Vth = a আর b-এর মাঝে open-circuit voltage (Voc)।
  3. Rth = সব independent source kill করার পর a–b থেকে দেখা resistance (voltage source → short, current source → open)।
  4. Equivalent circuit-এ load আবার বসাও।
+−24 V6 Ω3 Ω2 ΩabOriginal circuit (load removed)+−Vth= 8 VRth = 4 ΩRLabThevenin equivalent + load
Left: the original circuit with the load removed. Right: its Thevenin equivalent (8 V with 4 Ω) driving the load RL.বামে: load সরানো আসল circuit। ডানে: এর Thevenin equivalent (8 V আর 4 Ω), যেটা load RL চালাচ্ছে।
Worked example: For the left circuit, find the Thevenin equivalent at a–b. Then find the load current for RL = 4 Ω and RL = 12 Ω.

Step 1 — Vth: With a–b open, no current flows in the 2 Ω, so it drops 0 V. The voltage at a = the voltage across the 3 Ω. The 6 Ω and 3 Ω form a voltage divider:

Vth = 24 × 3/(6 + 3) = 24/3 = 8 V.

Step 2 — Rth: Kill the 24 V source (short it). Looking in from a–b: the 2 Ω is in series with (6 ∥ 3).

6 ∥ 3 = 18/9 = 2 Ω → Rth = 2 + 2 = 4 Ω.

Step 3 — load current: IL = Vth/(Rth + RL).

  • RL = 4 Ω: IL = 8/(4 + 4) = 1 A.
  • RL = 12 Ω: IL = 8/(4 + 12) = 0.5 A.
Worked example: বামের circuit-এর a–b-তে Thevenin equivalent বের করো। তারপর RL = 4 Ω আর RL = 12 Ω হলে load current কত?

Step 1 — Vth: a–b open থাকলে 2 Ω দিয়ে কোনো current যায় না, তাই এর উপর 0 V drop। a-এর voltage = 3 Ω-এর উপরের voltage। 6 Ω আর 3 Ω একটা voltage divider:

Vth = 24 × 3/(6 + 3) = 24/3 = 8 V।

Step 2 — Rth: 24 V source kill করি (short)। a–b থেকে দেখলে: 2 Ω series-এ (6 ∥ 3)-এর সাথে।

6 ∥ 3 = 18/9 = 2 Ω → Rth = 2 + 2 = 4 Ω।

Step 3 — load current: IL = Vth/(Rth + RL)।

  • RL = 4 Ω: IL = 8/(4 + 4) = 1 A।
  • RL = 12 Ω: IL = 8/(4 + 12) = 0.5 A।
Most important exam rule — killing sources for Rth: voltage source → short (replace with a wire), current source → open (remove it). Many students do it the wrong way round. Memory trick: a dead voltage source gives 0 V, and only a wire has 0 V across it. A dead current source gives 0 A, and only a break has 0 A through it. (If the circuit has dependent sources, keep them and use Rth = Voc/Isc, or apply a 1 A test source.)
Exam-এর সবচেয়ে জরুরি নিয়ম — Rth-এর জন্য source kill করা: voltage source → short (wire দিয়ে বদলাও), current source → open (সরিয়ে দাও)। অনেকে উল্টো করে ফেলে। মনে রাখার কৌশল: মরা voltage source 0 V দেয়, আর শুধু wire-এর উপর 0 V থাকে। মরা current source 0 A দেয়, আর শুধু কাটা জায়গা দিয়ে 0 A যায়। (Circuit-এ dependent source থাকলে সেটা রেখে দাও, আর Rth = Voc/Isc ব্যবহার করো, বা 1 A test source লাগাও।)

Norton's theorem and Thevenin ↔ NortonNorton's theorem আর Thevenin ↔ Norton

Statement: Any linear circuit seen from a–b can also be replaced by one current source IN in parallel with one resistor RN.

  • IN = the short-circuit current from a to b (Isc).
  • RN = Rth (found the same way).

Norton is just a source transformation of Thevenin. So:

Statement: যেকোনো linear circuit-কে a–b থেকে দেখলে সেটাকে একটা current source IN আর তার সাথে parallel-এ একটা resistor RN দিয়েও বদলানো যায়।

  • IN = a থেকে b-তে short-circuit current (Isc)।
  • RN = Rth (একইভাবে বের করা হয়)।

Norton হলো Thevenin-এর একটা source transformation মাত্র। তাই:

\[ I_N = \frac{V_{th}}{R_{th}} \qquad V_{th} = I_N R_N \qquad R_N = R_{th} = \frac{V_{oc}}{I_{sc}} \]
Example (same circuit): Find the Norton equivalent, and check IN directly.

From Thevenin: IN = 8/4 = 2 A, RN = 4 Ω.

Direct check: short a to b. Now the 2 Ω goes from the middle node (call it Vm) to ground. KCL at Vm: (Vm − 24)/6 + Vm/3 + Vm/2 = 0 → ×6: Vm − 24 + 2Vm + 3Vm = 0 → Vm = 4 V. Short-circuit current = 4/2 = 2 A ✓.

Example (একই circuit): Norton equivalent বের করো, আর IN সরাসরি check করো।

Thevenin থেকে: IN = 8/4 = 2 A, RN = 4 Ω।

সরাসরি check: a আর b short করি। এখন 2 Ω মাঝের node (নাম Vm) থেকে ground-এ যায়। Vm-এ KCL: (Vm − 24)/6 + Vm/3 + Vm/2 = 0 → ×6: Vm − 24 + 2Vm + 3Vm = 0 → Vm = 4 V। Short-circuit current = 4/2 = 2 A ✓।

Maximum power transferMaximum power transfer

Statement: A load gets the maximum power when its resistance equals the Thevenin resistance of the circuit feeding it: RL = Rth.

Why: PL = I²RL = Vth² RL/(Rth + RL)². Too small RL → big current but tiny voltage. Too big RL → big voltage but tiny current. The best is in the middle. Setting dP/dRL = 0 gives RL = Rth.

Statement: একটা load সর্বোচ্চ power পায় যখন তার resistance তাকে চালানো circuit-এর Thevenin resistance-এর সমান: RL = Rth।

কেন: PL = I²RL = Vth² RL/(Rth + RL)²। RL খুব ছোট → current বেশি কিন্তু voltage খুব কম। RL খুব বড় → voltage বেশি কিন্তু current খুব কম। সবচেয়ে ভালো মাঝখানে। dP/dRL = 0 বসালে পাই RL = Rth।

\[ P_L = \frac{V_{th}^2\, R_L}{(R_{th} + R_L)^2} \qquad\text{max when}\quad R_L = R_{th} \qquad P_{\max} = \frac{V_{th}^2}{4 R_{th}} \]
Worked example (same circuit, Vth = 8 V, Rth = 4 Ω): Find RL for maximum power and Pmax. Make a table to see it.

RL = Rth = 4 Ω. Pmax = 8²/(4 × 4) = 64/16 = 4 W.

RL (Ω)I = 8/(4 + RL) (A)P = I²RL (W)
11.62.56
21.3333.56
41.04.00 (max)
80.6673.56
160.42.56

The power rises, peaks at RL = 4 Ω, then falls ✓.

Worked example (একই circuit, Vth = 8 V, Rth = 4 Ω): Maximum power-এর জন্য RL আর Pmax বের করো। একটা table বানিয়ে দেখো।

RL = Rth = 4 Ω। Pmax = 8²/(4 × 4) = 64/16 = 4 W।

RL (Ω)I = 8/(4 + RL) (A)P = I²RL (W)
11.62.56
21.3333.56
41.04.00 (max)
80.6673.56
160.42.56

Power বাড়ে, RL = 4 Ω-এ সর্বোচ্চ হয়, তারপর কমে ✓।

Note: At maximum power transfer, the efficiency is only 50% — the same power is lost inside Rth. That is fine for signals (antennas, amplifiers, communication), but power grids do not run at this point. For AC circuits the rule becomes ZL = Zth* (complex conjugate).
Note: Maximum power transfer-এ efficiency মাত্র 50% — সমান power Rth-এর ভিতরে নষ্ট হয়। Signal-এর জন্য (antenna, amplifier, communication) এটা ঠিক আছে, কিন্তু power grid এই অবস্থায় চলে না। AC circuit-এ নিয়মটা হয় ZL = Zth* (complex conjugate)।

5. Capacitors and Inductors5. Capacitor আর Inductor

Resistors only waste energy as heat. Capacitors and inductors store energy and give it back later. That is why they create "memory" and time-changing behavior in circuits.

  • A capacitor stores energy in an electric field (between two metal plates). It "resists" sudden changes of voltage.
  • An inductor stores energy in a magnetic field (in a coil of wire). It "resists" sudden changes of current.

Resistor শুধু energy তাপ হিসেবে নষ্ট করে। Capacitor আর inductor energy জমা রাখে, পরে ফেরত দেয়। এজন্যই circuit-এ এরা "memory" আর সময়ের সাথে বদলানো আচরণ তৈরি করে।

  • Capacitor energy জমা রাখে electric field-এ (দুইটা metal plate-এর মাঝে)। এটা voltage-এর হঠাৎ পরিবর্তন "ঠেকায়"।
  • Inductor energy জমা রাখে magnetic field-এ (wire-এর coil-এ)। এটা current-এর হঠাৎ পরিবর্তন "ঠেকায়"।
Different kinds of real capacitors
Real capacitors of different types and sizes. (Image: Wikimedia Commons)বিভিন্ন ধরন আর আকারের বাস্তব capacitor। (Image: Wikimedia Commons)

Capacitor relationsCapacitor-এর সম্পর্ক

Capacitance C tells how much charge the capacitor holds per volt. Unit: farad (F). Real values are small: μF, nF, pF. For two parallel plates of area A, gap d, and permittivity ε: C = εA/d.

Current flows through a capacitor only when its voltage is changing. If the voltage is constant (DC), the current is zero.

Capacitance C বলে প্রতি volt-এ capacitor কত charge ধরে রাখে। Unit: farad (F)। বাস্তবে মান ছোট: μF, nF, pF। দুইটা parallel plate (area A, দূরত্ব d, permittivity ε) হলে: C = εA/d।

Capacitor দিয়ে current যায় শুধু তখনই যখন এর voltage বদলাচ্ছে। Voltage স্থির (DC) হলে current শূন্য।

\[ Q = CV \qquad i = C\,\frac{dv}{dt} \qquad v(t) = \frac{1}{C}\int_0^t i\,dt + v(0) \qquad W_C = \tfrac{1}{2} C V^2 \qquad C = \frac{\varepsilon A}{d} \]
Example 1: A 100 μF capacitor is charged to 12 V. Find the charge and the stored energy.

Q = CV = 100 × 10⁻⁶ × 12 = 1.2 × 10⁻³ C = 1.2 mC.

W = ½CV² = ½ × 100 × 10⁻⁶ × 144 = 7.2 mJ.

Example 1: একটা 100 μF capacitor 12 V-এ charge করা। Charge আর জমা energy কত?

Q = CV = 100 × 10⁻⁶ × 12 = 1.2 × 10⁻³ C = 1.2 mC।

W = ½CV² = ½ × 100 × 10⁻⁶ × 144 = 7.2 mJ।

Example 2: The voltage on a 10 μF capacitor rises steadily from 0 to 50 V in 5 ms. Find the current.

dv/dt = 50/(5 × 10⁻³) = 10,000 V/s. i = C dv/dt = 10 × 10⁻⁶ × 10,000 = 0.1 A. After the voltage stops changing, i = 0.

Example 2: একটা 10 μF capacitor-এর voltage 5 ms-এ সমানভাবে 0 থেকে 50 V হয়। Current কত?

dv/dt = 50/(5 × 10⁻³) = 10,000 V/s। i = C dv/dt = 10 × 10⁻⁶ × 10,000 = 0.1 A। Voltage বদলানো থামলে i = 0।

Example 3: Parallel plates: A = 0.01 m², d = 1 mm, air (ε = ε₀ = 8.854 × 10⁻¹² F/m). Find C.

C = ε₀A/d = 8.854 × 10⁻¹² × 0.01/10⁻³ = 8.854 × 10⁻¹¹ F = 88.54 pF. Very small — that is why real capacitors roll up long thin plates.

Example 3: Parallel plate: A = 0.01 m², d = 1 mm, বাতাস (ε = ε₀ = 8.854 × 10⁻¹² F/m)। C কত?

C = ε₀A/d = 8.854 × 10⁻¹² × 0.01/10⁻³ = 8.854 × 10⁻¹¹ F = 88.54 pF। খুব ছোট — এজন্যই বাস্তব capacitor-এ লম্বা পাতলা plate পেঁচিয়ে রাখা হয়।

Inductor relationsInductor-এর সম্পর্ক

Inductance L tells how much voltage appears when the current changes. Unit: henry (H). A voltage appears across an inductor only when its current is changing. For steady DC current, the voltage is zero — it acts like a plain wire.

Inductance L বলে current বদলালে কত voltage তৈরি হয়। Unit: henry (H)। Inductor-এর উপর voltage আসে শুধু যখন এর current বদলাচ্ছে। স্থির DC current-এ voltage শূন্য — এটা একটা সাধারণ wire-এর মতো আচরণ করে।

\[ v = L\,\frac{di}{dt} \qquad i(t) = \frac{1}{L}\int_0^t v\,dt + i(0) \qquad W_L = \tfrac{1}{2} L I^2 \]
Example 4: The current in a 20 mH inductor changes by 2 A in 4 ms. Find the voltage.

di/dt = 2/(4 × 10⁻³) = 500 A/s. v = L di/dt = 0.02 × 500 = 10 V.

Example 4: একটা 20 mH inductor-এর current 4 ms-এ 2 A বদলায়। Voltage কত?

di/dt = 2/(4 × 10⁻³) = 500 A/s। v = L di/dt = 0.02 × 500 = 10 V।

Example 5: A 0.5 H inductor carries 4 A. Find the stored energy.

W = ½LI² = ½ × 0.5 × 16 = 4 J.

Example 5: একটা 0.5 H inductor দিয়ে 4 A যাচ্ছে। জমা energy কত?

W = ½LI² = ½ × 0.5 × 16 = 4 J।

Continuity rule (very important for transients): Capacitor voltage cannot jump instantly (that would need infinite current). Inductor current cannot jump instantly (that would need infinite voltage). So vC(0⁺) = vC(0⁻) and iL(0⁺) = iL(0⁻). This is why opening a switch on an inductor makes a spark.
Continuity নিয়ম (transient-এর জন্য খুব জরুরি): Capacitor-এর voltage হঠাৎ লাফ দিতে পারে না (তাহলে অসীম current লাগত)। Inductor-এর current হঠাৎ লাফ দিতে পারে না (তাহলে অসীম voltage লাগত)। তাই vC(0⁺) = vC(0⁻) আর iL(0⁺) = iL(0⁻)। Inductor-ওয়ালা circuit-এ switch খুললে এজন্যই spark হয়।

Series and parallel combinationsSeries আর parallel combination

Inductors combine exactly like resistors. Capacitors combine the opposite way:

Inductor ঠিক resistor-এর মতো combine হয়। Capacitor combine হয় উল্টোভাবে:

SeriesSeriesParallelParallel
Resistor RR₁ + R₂ + …1/R = 1/R₁ + 1/R₂ + …
Inductor LL₁ + L₂ + …1/L = 1/L₁ + 1/L₂ + …
Capacitor C1/C = 1/C₁ + 1/C₂ + …C₁ + C₂ + …

Why capacitors are opposite: in parallel, the plates are side by side, so the total plate area grows → more C. In series, the gap effectively grows → less C.

Capacitor কেন উল্টো: parallel-এ plate গুলো পাশাপাশি থাকে, তাই মোট plate area বাড়ে → C বেশি। Series-এ কার্যত দূরত্ব বাড়ে → C কম।

Example 6: 6 μF and 3 μF capacitors. (a) Series. (b) Parallel. (c) In series across 12 V, find the voltage on each.

(a) C = (6 × 3)/(6 + 3) = 2 μF. (b) C = 6 + 3 = 9 μF.

(c) Series capacitors carry the same charge: Q = CeqV = 2 μF × 12 = 24 μC. V6μF = 24/6 = 4 V, V3μF = 24/3 = 8 V. The smaller capacitor gets the bigger voltage. Check: 4 + 8 = 12 ✓.

Inductors 6 mH and 3 mH: series = 9 mH, parallel = (6 × 3)/9 = 2 mH (just like resistors).

Example 6: 6 μF আর 3 μF capacitor। (a) Series। (b) Parallel। (c) Series-এ 12 V-এ লাগালে প্রতিটার voltage কত?

(a) C = (6 × 3)/(6 + 3) = 2 μF। (b) C = 6 + 3 = 9 μF।

(c) Series capacitor-এ একই charge থাকে: Q = CeqV = 2 μF × 12 = 24 μC। V6μF = 24/6 = 4 V, V3μF = 24/3 = 8 V। ছোট capacitor পায় বেশি voltage। Check: 4 + 8 = 12 ✓।

Inductor 6 mH আর 3 mH: series = 9 mH, parallel = (6 × 3)/9 = 2 mH (resistor-এর মতোই)।

Exam trap: Capacitors in series/parallel are opposite to resistors. Two equal capacitors C in series → C/2. In parallel → 2C. Students lose easy MCQ marks here.
Exam ফাঁদ: Series/parallel-এ capacitor resistor-এর উল্টো। দুইটা সমান C series-এ → C/2। Parallel-এ → 2C। এখানে সহজ MCQ-তে অনেকে নম্বর হারায়।

DC steady-state behaviorDC steady-state আচরণ

Wait a long time after a DC source is switched on. Nothing changes any more (steady state). Then:

  • dv/dt = 0 → capacitor current = 0 → capacitor = open circuit.
  • di/dt = 0 → inductor voltage = 0 → inductor = short circuit.

So for DC steady state: remove every capacitor, replace every inductor with a wire, and solve the resistor circuit. Then find the capacitor voltage and inductor current to get the stored energy.

DC source চালু করার পর অনেকক্ষণ অপেক্ষা করো। আর কিছু বদলায় না (steady state)। তখন:

  • dv/dt = 0 → capacitor current = 0 → capacitor = open circuit।
  • di/dt = 0 → inductor voltage = 0 → inductor = short circuit।

তাই DC steady state-এ: সব capacitor সরিয়ে দাও, সব inductor-কে wire দিয়ে বদলাও, তারপর resistor circuit solve করো। এরপর capacitor voltage আর inductor current থেকে জমা energy বের করো।

+−12 V2 ΩC = 1 mFL = 0.5 H4 ΩAAt DC steady state:C → open circuitL → short circuitI = 12 / (2 + 4) = 2 A
A DC circuit with one capacitor and one inductor. In steady state C is open and L is a short.একটা capacitor আর একটা inductor-ওয়ালা DC circuit। Steady state-এ C open আর L short।
Worked example: In the circuit above, find the inductor current, the capacitor voltage, and the energy stored in each at DC steady state.

C → open, L → short. Now the circuit is just 12 V, 2 Ω and 4 Ω in series.

I = 12/(2 + 4) = 2 A. This flows through L, so iL = 2 A.

The capacitor sits between node A and ground. VA = 12 − 2 × 2 = 8 V (also = 2 A × 4 Ω, because L has 0 V). So vC = 8 V.

WC = ½ × 10⁻³ × 8² = 32 mJ. WL = ½ × 0.5 × 2² = 1 J.

Worked example: উপরের circuit-এ DC steady state-এ inductor current, capacitor voltage আর প্রতিটায় জমা energy বের করো।

C → open, L → short। এখন circuit শুধু 12 V, 2 Ω আর 4 Ω series-এ।

I = 12/(2 + 4) = 2 A। এটা L দিয়ে যায়, তাই iL = 2 A।

Capacitor আছে node A আর ground-এর মাঝে। VA = 12 − 2 × 2 = 8 V (আবার = 2 A × 4 Ω, কারণ L-এর উপর 0 V)। তাই vC = 8 V।

WC = ½ × 10⁻³ × 8² = 32 mJ। WL = ½ × 0.5 × 2² = 1 J।

CapacitorInductor
Stores energy inEnergy জমা রাখেelectric fieldmagnetic field
Cannot change suddenlyহঠাৎ বদলাতে পারে নাvoltagecurrent
DC steady stateDC steady stateopen circuitshort circuit
At very high frequencyখুব বেশি frequency-তেshort circuitopen circuit
EnergyEnergy½CV²½LI²
Series combineSeries combinelike parallel Rlike series R

6. First-Order Transients (RC and RL)6. First-Order Transients (RC আর RL)

A transient is what happens right after a switch changes, before the circuit settles down. A circuit with one capacitor (RC) or one inductor (RL) is called first-order, because it gives a first-order differential equation. The answer is always an exponential curve.

The speed of the curve is set by the time constant τ (tau):

Transient হলো switch বদলানোর ঠিক পরে, circuit স্থির হওয়ার আগে যা ঘটে। একটা capacitor (RC) বা একটা inductor (RL)-ওয়ালা circuit-কে first-order বলে, কারণ এটা first-order differential equation দেয়। উত্তর সবসময় একটা exponential curve।

Curve কত দ্রুত চলবে, সেটা ঠিক করে time constant τ (tau):

\[ \text{RC circuit: } \tau = RC \qquad\qquad \text{RL circuit: } \tau = \frac{L}{R} \qquad (\text{unit: seconds}) \]

Here R is the Thevenin resistance seen by the C or L (kill the sources, look in from the capacitor/inductor terminals).

এখানে R হলো C বা L যে Thevenin resistance দেখে সেটা (source kill করে capacitor/inductor-এর terminal থেকে ভিতরে দেখো)।

RC chargingRC charging

An empty capacitor (v = 0) is connected through R to a DC source Vs at t = 0. At first, the capacitor acts like a short, so the current is big: Vs/R. As it charges, its voltage rises and the current falls. Finally v = Vs and i = 0.

একটা খালি capacitor (v = 0) t = 0-তে R-এর মধ্য দিয়ে একটা DC source Vs-এ লাগানো হলো। শুরুতে capacitor short-এর মতো, তাই current বড়: Vs/R। Charge হতে হতে এর voltage বাড়ে আর current কমে। শেষে v = Vs আর i = 0।

\[ v_C(t) = V_s\left(1 - e^{-t/\tau}\right) \qquad i(t) = \frac{V_s}{R}\,e^{-t/\tau} \qquad \tau = RC \]

RC dischargingRC discharging

A capacitor charged to V₀ is connected across R (no source). It pushes current through R and its voltage decays to 0.

V₀ পর্যন্ত charge করা একটা capacitor শুধু R-এর সাথে লাগানো (source নেই)। এটা R দিয়ে current পাঠায়, আর এর voltage কমে 0 হয়ে যায়।

\[ v_C(t) = V_0\, e^{-t/\tau} \qquad i(t) = \frac{V_0}{R}\,e^{-t/\tau} \]
tv(t)Vs1τ2τ3τ4τ5τ063.2%86.5%99.3%36.8%charging: Vs(1 − e^(−t/τ))discharging: V0·e^(−t/τ)
RC charging (solid) and discharging (dashed). After 1τ: 63.2% charged (or 36.8% left). After 5τ: practically done.RC charging (সলিড) আর discharging (ড্যাশ)। 1τ পরে: 63.2% charge (বা 36.8% বাকি)। 5τ পরে: কার্যত শেষ।
tτ2τ3τ4τ5τ
Charging: % of finalCharging: final-এর %63.2%86.5%95.0%98.2%99.3%
Discharging: % leftDischarging: % বাকি36.8%13.5%5.0%1.8%0.7%
Worked example (RC charging): Vs = 10 V, R = 10 kΩ, C = 100 μF. The capacitor starts empty. Find τ, vC at t = 1 s, 2 s, 5 s, the initial current, and the time to reach 5 V.

τ = RC = 10 × 10³ × 100 × 10⁻⁶ = 1 s.

v(1 s) = 10(1 − e⁻¹) = 10 × 0.632 = 6.32 V (63.2% at t = τ).

v(2 s) = 10(1 − e⁻²) = 10 × 0.865 = 8.65 V.

v(5 s) = 10(1 − e⁻⁵) = 10 × 0.993 = 9.93 V → steady state after about 5τ.

i(0) = Vs/R = 10/10,000 = 1 mA. i(1 s) = 1 × e⁻¹ = 0.368 mA.

Time to 5 V (half): 5 = 10(1 − e−t) → e−t = 0.5 → t = ln 2 × τ = 0.693 s.

Worked example (RC charging): Vs = 10 V, R = 10 kΩ, C = 100 μF। Capacitor শুরুতে খালি। τ, t = 1 s, 2 s, 5 s-এ vC, শুরুর current, আর 5 V হতে কত সময় লাগে বের করো।

τ = RC = 10 × 10³ × 100 × 10⁻⁶ = 1 s।

v(1 s) = 10(1 − e⁻¹) = 10 × 0.632 = 6.32 V (t = τ-তে 63.2%)।

v(2 s) = 10(1 − e⁻²) = 10 × 0.865 = 8.65 V।

v(5 s) = 10(1 − e⁻⁵) = 10 × 0.993 = 9.93 V → প্রায় 5τ পরে steady state।

i(0) = Vs/R = 10/10,000 = 1 mA। i(1 s) = 1 × e⁻¹ = 0.368 mA।

5 V (অর্ধেক) হওয়ার সময়: 5 = 10(1 − e−t) → e−t = 0.5 → t = ln 2 × τ = 0.693 s।

Example (RC discharging): A 100 μF capacitor at 100 V discharges through 20 kΩ. Find τ, v at 2 s and 4 s, and the starting energy.

τ = 20 × 10³ × 100 × 10⁻⁶ = 2 s. v(2 s) = 100e⁻¹ = 36.8 V. v(4 s) = 100e⁻² = 13.5 V.

Energy at start = ½ × 100 × 10⁻⁶ × 100² = 0.5 J. All of it ends up as heat in the resistor.

Example (RC discharging): 100 V-এ থাকা একটা 100 μF capacitor 20 kΩ দিয়ে discharge হয়। τ, 2 s আর 4 s-এ v, আর শুরুর energy বের করো।

τ = 20 × 10³ × 100 × 10⁻⁶ = 2 s। v(2 s) = 100e⁻¹ = 36.8 V। v(4 s) = 100e⁻² = 13.5 V।

শুরুর energy = ½ × 100 × 10⁻⁶ × 100² = 0.5 J। পুরোটাই শেষে resistor-এ তাপ হয়ে যায়।

RL circuitRL circuit

An RL circuit works the same way, but now the current is the smooth quantity. When a DC source Vs is switched on, the inductor current rises from 0 to Vs/R. The inductor voltage starts at Vs and decays to 0.

RL circuit একইভাবে কাজ করে, কিন্তু এখানে current হলো মসৃণভাবে বদলানো রাশি। DC source Vs চালু করলে inductor current 0 থেকে Vs/R পর্যন্ত বাড়ে। Inductor voltage Vs থেকে শুরু হয়ে কমে 0 হয়।

\[ i_L(t) = \frac{V_s}{R}\left(1 - e^{-t/\tau}\right) \qquad v_L(t) = V_s\,e^{-t/\tau} \qquad \tau = \frac{L}{R} \]
Worked example (RL): Vs = 12 V, R = 4 Ω, L = 2 H, switch closed at t = 0. Find τ, the final current, i at t = τ, and vL(0).

τ = L/R = 2/4 = 0.5 s. Final current = 12/4 = 3 A.

i(t) = 3(1 − e−2t) A. At t = 0.5 s: i = 3 × 0.632 = 1.90 A. At t = 2.5 s (5τ): i = 3 × 0.993 = 2.98 A ≈ 3 A.

vL(0) = 12 V (at t = 0 the current is still 0, so no drop on R, all 12 V is on L).

Worked example (RL): Vs = 12 V, R = 4 Ω, L = 2 H, t = 0-তে switch বন্ধ। τ, final current, t = τ-তে i, আর vL(0) বের করো।

τ = L/R = 2/4 = 0.5 s। Final current = 12/4 = 3 A।

i(t) = 3(1 − e−2t) A। t = 0.5 s-এ: i = 3 × 0.632 = 1.90 A। t = 2.5 s (5τ)-এ: i = 3 × 0.993 = 2.98 A ≈ 3 A।

vL(0) = 12 V (t = 0-তে current তখনো 0, তাই R-এ drop নেই, পুরো 12 V L-এর উপর)।

The one general formulaএকটাই general formula

You can solve almost any first-order problem with one formula. You only need three things: the initial value x(0), the final value x(∞), and τ.

প্রায় যেকোনো first-order problem একটা formula দিয়েই solve করা যায়। শুধু তিনটা জিনিস লাগে: initial value x(0), final value x(∞), আর τ।

\[ x(t) = x(\infty) + \big[x(0) - x(\infty)\big]\,e^{-t/\tau} \]
  1. x(0): use the continuity rule (vC or iL just before the switch).
  2. x(∞): DC steady state after the switch (C open, L short).
  3. τ: RC or L/R using the Thevenin R seen by C or L after the switch.
  1. x(0): continuity নিয়ম ব্যবহার করো (switch-এর ঠিক আগের vC বা iL)।
  2. x(∞): switch-এর পরের DC steady state (C open, L short)।
  3. τ: switch-এর পরে C বা L যে Thevenin R দেখে, সেটা দিয়ে RC বা L/R।
Example: A capacitor already has 2 V. At t = 0 it is connected through a resistor to 12 V. τ = 0.1 s. Find v at t = 0.1 s.

x(0) = 2 V, x(∞) = 12 V. v(t) = 12 + (2 − 12)e−t/0.1 = 12 − 10e−10t.

v(0.1) = 12 − 10e⁻¹ = 12 − 3.68 = 8.32 V.

Example: একটা capacitor-এ আগে থেকেই 2 V আছে। t = 0-তে এটাকে একটা resistor দিয়ে 12 V-এ লাগানো হলো। τ = 0.1 s। t = 0.1 s-এ v কত?

x(0) = 2 V, x(∞) = 12 V। v(t) = 12 + (2 − 12)e−t/0.1 = 12 − 10e−10t।

v(0.1) = 12 − 10e⁻¹ = 12 − 3.68 = 8.32 V।

Numbers to remember: e⁻¹ = 0.368, e⁻² = 0.135, e⁻³ = 0.050, e⁻⁵ = 0.0067, ln 2 = 0.693. At t = τ → 63.2% of the change is done. After 5τ → we say "steady state". A bigger R or bigger C → slower (bigger τ). For RL, a bigger R → faster (τ = L/R).
মনে রাখার সংখ্যা: e⁻¹ = 0.368, e⁻² = 0.135, e⁻³ = 0.050, e⁻⁵ = 0.0067, ln 2 = 0.693। t = τ-তে → পরিবর্তনের 63.2% শেষ। 5τ পরে → আমরা বলি "steady state"। R বা C বড় → ধীর (τ বড়)। RL-এ R বড় → দ্রুত (τ = L/R)।

7. AC Circuit Basics7. AC Circuit Basics

The sinusoidSinusoid

In AC (alternating current), the voltage goes up and down like a sine wave. Our home supply in Bangladesh is 220 V, 50 Hz. A sinusoid is written as:

AC (alternating current)-এ voltage sine wave-এর মতো উঠানামা করে। বাংলাদেশে বাসার supply হলো 220 V, 50 Hz। একটা sinusoid লেখা হয় এভাবে:

\[ v(t) = V_m \sin(\omega t + \phi) \qquad \omega = 2\pi f \qquad T = \frac{1}{f} \]
  • Vm = amplitude (peak value).
  • ω = angular frequency (rad/s). f = frequency (Hz). T = period (s).
  • φ = phase angle — how much the wave is shifted.
  • Vm = amplitude (peak value)।
  • ω = angular frequency (rad/s)। f = frequency (Hz)। T = period (s)।
  • φ = phase angle — wave-টা কতটা সরানো।
ωtVmone period T = 1/fv(t) — voltagei(t) — current (lagging)
A sinusoidal voltage (solid) and a current that lags it (dashed), as in an inductive circuit.একটা sinusoidal voltage (সলিড) আর তার পিছনে থাকা (lagging) current (ড্যাশ), যেমন inductive circuit-এ হয়।

RMS valueRMS value

The average of a full sine wave is zero, so average is not useful. Instead we use the RMS (root mean square) value. RMS is the DC value that gives the same heating in a resistor. When we say "220 V AC", we mean 220 V RMS.

পুরো একটা sine wave-এর average শূন্য, তাই average কাজে লাগে না। এর বদলে আমরা RMS (root mean square) value ব্যবহার করি। RMS হলো সেই DC মান যেটা resistor-এ একই তাপ দেয়। "220 V AC" বললে আমরা 220 V RMS বোঝাই।

\[ V_{rms} = \frac{V_m}{\sqrt{2}} \approx 0.707\,V_m \qquad I_{rms} = \frac{I_m}{\sqrt{2}} \qquad V_{avg,\ half\ cycle} = \frac{2V_m}{\pi} \approx 0.637\,V_m \]
Example 1: v(t) = 170 sin(377t + 30°) V. Find Vm, ω, f, T, Vrms and the phase.

Vm = 170 V, ω = 377 rad/s, f = 377/(2π) = 60 Hz, T = 1/60 = 16.67 ms.

Vrms = 170/√2 = 120.2 V (this is the USA supply). Phase = +30°.

Example 1: v(t) = 170 sin(377t + 30°) V। Vm, ω, f, T, Vrms আর phase বের করো।

Vm = 170 V, ω = 377 rad/s, f = 377/(2π) = 60 Hz, T = 1/60 = 16.67 ms।

Vrms = 170/√2 = 120.2 V (এটা USA-র supply)। Phase = +30°।

Example 2: Bangladesh supply: 220 V RMS, 50 Hz. Find the peak voltage, ω and T.

Vm = 220 × √2 = 311 V. ω = 2π × 50 = 314.16 rad/s. T = 1/50 = 20 ms. So v(t) = 311 sin(314t) V.

Example 2: বাংলাদেশের supply: 220 V RMS, 50 Hz। Peak voltage, ω আর T কত?

Vm = 220 × √2 = 311 V। ω = 2π × 50 = 314.16 rad/s। T = 1/50 = 20 ms। তাই v(t) = 311 sin(314t) V।

PhasorsPhasor

In a linear AC circuit, every voltage and current has the same frequency. Only the size and the phase are different. So we drop the "sin ωt" part and keep just a complex number: size ∠ angle. This is a phasor. It turns calculus (d/dt) into simple algebra.

  • Polar form: A∠θ. Rectangular form: a + jb (j = √−1, engineers use j because i is current).
  • a = A cos θ, b = A sin θ. A = √(a² + b²), θ = tan⁻¹(b/a).
  • Add/subtract → use rectangular. Multiply/divide → use polar (multiply sizes, add angles).

Linear AC circuit-এ সব voltage আর current-এর frequency একই। শুধু আকার আর phase আলাদা। তাই "sin ωt" অংশ বাদ দিয়ে শুধু একটা complex number রাখি: আকার ∠ কোণ। এটাই phasor। এটা calculus (d/dt)-কে সহজ algebra বানিয়ে দেয়।

  • Polar form: A∠θ। Rectangular form: a + jb (j = √−1, engineer-রা j লেখে কারণ i মানে current)।
  • a = A cos θ, b = A sin θ। A = √(a² + b²), θ = tan⁻¹(b/a)।
  • যোগ/বিয়োগ → rectangular ব্যবহার করো। গুণ/ভাগ → polar ব্যবহার করো (আকার গুণ, কোণ যোগ)।
Example 3: (a) Convert 10∠30° to rectangular. (b) Convert 3 + j4 to polar. (c) Find (10∠30°)/(3 + j4).

(a) 10cos30° + j10sin30° = 8.66 + j5.

(b) √(9 + 16) = 5, tan⁻¹(4/3) = 53.13° → 5∠53.13°.

(c) (10/5)∠(30° − 53.13°) = 2∠−23.13°.

Example 3: (a) 10∠30°-কে rectangular-এ নাও। (b) 3 + j4-কে polar-এ নাও। (c) (10∠30°)/(3 + j4) বের করো।

(a) 10cos30° + j10sin30° = 8.66 + j5।

(b) √(9 + 16) = 5, tan⁻¹(4/3) = 53.13° → 5∠53.13°।

(c) (10/5)∠(30° − 53.13°) = 2∠−23.13°।

Impedance and reactanceImpedance আর reactance

Impedance Z is the AC version of resistance: V = IZ (Ohm's law with phasors). It is a complex number: Z = R + jX. The real part R is resistance. The imaginary part X is reactance. Unit of both: Ω.

  • Resistor: Z = R. Voltage and current are in phase.
  • Inductor: Z = jωL. Reactance XL = ωL = 2πfL. It grows with frequency.
  • Capacitor: Z = 1/(jωC) = −j/(ωC). Reactance XC = 1/(ωC) = 1/(2πfC). It falls with frequency.

Impedances combine exactly like resistors (series add, parallel product-over-sum), but using complex numbers. KCL, KVL, nodal, mesh, Thevenin — all work the same with phasors.

Impedance Z হলো resistance-এর AC রূপ: V = IZ (phasor দিয়ে Ohm's law)। এটা একটা complex number: Z = R + jX। Real অংশ R হলো resistance। Imaginary অংশ X হলো reactance। দুইটারই unit: Ω।

  • Resistor: Z = R। Voltage আর current একই phase-এ।
  • Inductor: Z = jωL। Reactance XL = ωL = 2πfL। Frequency বাড়লে বাড়ে।
  • Capacitor: Z = 1/(jωC) = −j/(ωC)। Reactance XC = 1/(ωC) = 1/(2πfC)। Frequency বাড়লে কমে।

Impedance ঠিক resistor-এর মতো combine হয় (series-এ যোগ, parallel-এ product-over-sum), শুধু complex number দিয়ে। KCL, KVL, nodal, mesh, Thevenin — phasor দিয়ে সব একইভাবে কাজ করে।

\[ Z_R = R \qquad Z_L = j\omega L \qquad Z_C = \frac{1}{j\omega C} = -\frac{j}{\omega C} \qquad X_L = 2\pi f L \qquad X_C = \frac{1}{2\pi f C} \]
Example 4: At 50 Hz, find the reactance of a 0.1 H inductor and a 100 μF capacitor. What happens at 100 Hz?

XL = 2π × 50 × 0.1 = 31.42 Ω. XC = 1/(2π × 50 × 100 × 10⁻⁶) = 31.83 Ω.

At 100 Hz: XL doubles to 62.83 Ω, XC halves to 15.92 Ω. At DC (f = 0): XL = 0 (short) and XC = ∞ (open) — the same as Section 5 ✓.

Example 4: 50 Hz-এ একটা 0.1 H inductor আর একটা 100 μF capacitor-এর reactance কত? 100 Hz-এ কী হয়?

XL = 2π × 50 × 0.1 = 31.42 Ω। XC = 1/(2π × 50 × 100 × 10⁻⁶) = 31.83 Ω।

100 Hz-এ: XL দ্বিগুণ হয়ে 62.83 Ω, XC অর্ধেক হয়ে 15.92 Ω। DC-তে (f = 0): XL = 0 (short) আর XC = ∞ (open) — Section 5-এর সাথে মিলে যায় ✓।

Series RLC — worked exampleSeries RLC — worked example

\[ Z = R + j(X_L - X_C) \qquad |Z| = \sqrt{R^2 + (X_L - X_C)^2} \qquad \theta = \tan^{-1}\frac{X_L - X_C}{R} \]
200 VrmsR = 60 ΩL = 0.12 HC = 25 μFω = 1000 rad/sR = 60 ΩX = XL − XC= 80 Ω|Z| = 100 Ωθ = 53.13°impedance triangle
Series RLC circuit (left) and its impedance triangle (right): Z = 60 + j80 = 100∠53.13° Ω.Series RLC circuit (বামে) আর এর impedance triangle (ডানে): Z = 60 + j80 = 100∠53.13° Ω।
Worked example: R = 60 Ω, L = 0.12 H, C = 25 μF in series, fed by 200 V (RMS) at ω = 1000 rad/s. Find Z, the current, its phase, and each element voltage.

Step 1 — reactances: XL = ωL = 1000 × 0.12 = 120 Ω. XC = 1/(ωC) = 1/(1000 × 25 × 10⁻⁶) = 40 Ω.

Step 2 — impedance: Z = 60 + j(120 − 40) = 60 + j80 Ω. |Z| = √(3600 + 6400) = √10000 = 100 Ω. θ = tan⁻¹(80/60) = 53.13°.

Step 3 — current: I = V/Z = 200∠0° / 100∠53.13° = 2∠−53.13° A (RMS). The current lags the voltage by 53.13°, because XL > XC (the circuit is inductive).

Step 4 — element voltages (RMS): VR = 2 × 60 = 120 V, VL = 2 × 120 = 240 V, VC = 2 × 40 = 80 V.

Check: they add as phasors, not as plain numbers: √(120² + (240 − 80)²) = √(14400 + 25600) = 200 V ✓. Notice VL = 240 V is bigger than the source 200 V! This is normal in AC because VL and VC partly cancel.

Worked example: R = 60 Ω, L = 0.12 H, C = 25 μF series-এ, 200 V (RMS), ω = 1000 rad/s। Z, current, তার phase, আর প্রতিটা element-এর voltage বের করো।

Step 1 — reactance: XL = ωL = 1000 × 0.12 = 120 Ω। XC = 1/(ωC) = 1/(1000 × 25 × 10⁻⁶) = 40 Ω।

Step 2 — impedance: Z = 60 + j(120 − 40) = 60 + j80 Ω। |Z| = √(3600 + 6400) = √10000 = 100 Ω। θ = tan⁻¹(80/60) = 53.13°।

Step 3 — current: I = V/Z = 200∠0° / 100∠53.13° = 2∠−53.13° A (RMS)। Current voltage-এর চেয়ে 53.13° পিছিয়ে (lag), কারণ XL > XC (circuit-টা inductive)।

Step 4 — element voltage (RMS): VR = 2 × 60 = 120 V, VL = 2 × 120 = 240 V, VC = 2 × 40 = 80 V।

Check: এগুলো phasor হিসেবে যোগ হয়, সাধারণ সংখ্যার মতো না: √(120² + (240 − 80)²) = √(14400 + 25600) = 200 V ✓। খেয়াল করো VL = 240 V, source-এর 200 V-এর চেয়েও বেশি! AC-তে এটা স্বাভাবিক, কারণ VL আর VC একে অপরকে আংশিক কাটাকাটি করে।

Leading vs laggingLeading বনাম lagging

Element / circuitElement / circuitPhase of current vs voltageVoltage-এর তুলনায় current-এর phaseθ
Pure Rin phaseএকই phase0°
Pure Lcurrent lags by 90°current 90° lag করে+90°
Pure Ccurrent leads by 90°current 90° lead করে−90°
RL (XL > XC)lags by 0°–90° (inductive)0°–90° lag (inductive)positive
RC (XC > XL)leads by 0°–90° (capacitive)0°–90° lead (capacitive)negative
Memory trick — "ELI the ICE man": In an inductor (L), E (voltage) comes before I (current) → current lags. In a capacitor (C), I comes before E → current leads.
মনে রাখার কৌশল — "ELI the ICE man": Inductor (L)-এ E (voltage) আগে, I (current) পরে → current lag করে। Capacitor (C)-এ I আগে, E পরে → current lead করে।

8. AC Power and Resonance8. AC Power আর Resonance

Three kinds of powerতিন রকম power

In AC, the current and voltage are often not in phase. So not all of V × I does useful work. We split the power into three parts (V and I are RMS values, θ = angle of Z = angle by which current lags voltage):

  • Real (active) power P — the useful power that becomes heat, light or motion. Unit: watt (W). Only resistors take it.
  • Reactive power Q — power that goes back and forth between the source and L/C every cycle. It does no net work. Unit: VAR. Inductors take +Q, capacitors give (−Q).
  • Apparent power S — simply V × I. Unit: VA. Generators and transformers are rated in kVA because their wires must carry the full current.

AC-তে current আর voltage প্রায়ই একই phase-এ থাকে না। তাই V × I-এর পুরোটা কাজের কাজ করে না। আমরা power-কে তিন ভাগে ভাগ করি (V আর I RMS মান, θ = Z-এর কোণ = current voltage-এর চেয়ে যত কোণ পিছিয়ে):

  • Real (active) power P — কাজের power, যেটা তাপ, আলো বা গতি হয়। Unit: watt (W)। শুধু resistor এটা নেয়।
  • Reactive power Q — প্রতি cycle-এ source আর L/C-এর মাঝে আসা-যাওয়া করা power। এটা নিট কোনো কাজ করে না। Unit: VAR। Inductor +Q নেয়, capacitor Q দেয় (−Q)।
  • Apparent power S — সোজা V × I। Unit: VA। Generator আর transformer-এর rating kVA-তে হয়, কারণ তাদের wire-কে পুরো current বহন করতে হয়।
\[ P = V I \cos\theta = I^2 R \qquad Q = V I \sin\theta = I^2 X \qquad S = V I = I^2 |Z| \qquad S^2 = P^2 + Q^2 \] \[ \text{Power factor: } \; pf = \cos\theta = \frac{P}{S} = \frac{R}{|Z|} \qquad\qquad \mathbf{S} = \mathbf{V}\,\mathbf{I}^{*} = P + jQ \]
P = 240 W (real)Q = 320 VAR(reactive)S = 400 VA(apparent)θpf = cos θ = P / S= 240 / 400 = 0.6S² = P² + Q²400² = 240² + 320² ✓
Power triangle for the RLC example of Section 7: P = 240 W, Q = 320 VAR, S = 400 VA, pf = 0.6 lagging.Section 7-এর RLC example-এর power triangle: P = 240 W, Q = 320 VAR, S = 400 VA, pf = 0.6 lagging।
Worked example (continuing Section 7): V = 200 V, I = 2 A, θ = 53.13°. Find P, Q, S and pf.

cos 53.13° = 0.6, sin 53.13° = 0.8.

P = 200 × 2 × 0.6 = 240 W. Check: I²R = 4 × 60 = 240 W ✓.

Q = 200 × 2 × 0.8 = 320 VAR. Check: I²X = 4 × 80 = 320 VAR ✓.

S = 200 × 2 = 400 VA. Check: √(240² + 320²) = 400 ✓.

pf = 240/400 = 0.6 lagging (lagging because the load is inductive).

Worked example (Section 7-এর পরের অংশ): V = 200 V, I = 2 A, θ = 53.13°। P, Q, S আর pf বের করো।

cos 53.13° = 0.6, sin 53.13° = 0.8।

P = 200 × 2 × 0.6 = 240 W। Check: I²R = 4 × 60 = 240 W ✓।

Q = 200 × 2 × 0.8 = 320 VAR। Check: I²X = 4 × 80 = 320 VAR ✓।

S = 200 × 2 = 400 VA। Check: √(240² + 320²) = 400 ✓।

pf = 240/400 = 0.6 lagging (lagging কারণ load-টা inductive)।

Power factor correctionPower factor correction

Most loads (motors, fans, pumps) are inductive, so the pf is lagging (like 0.7–0.8). A low pf means more current for the same useful power. More current → bigger losses in wires (I²R) and bigger equipment. Power companies even fine big factories for low pf.

The fix: connect a capacitor in parallel with the load. The capacitor supplies reactive power (−Q) locally, so the source has to supply less Q. P does not change. The load itself does not change either.

বেশিরভাগ load (motor, fan, pump) inductive, তাই pf lagging (যেমন 0.7–0.8)। কম pf মানে একই কাজের power-এর জন্য বেশি current। বেশি current → wire-এ বেশি loss (I²R) আর বড় যন্ত্রপাতি। বড় কারখানাকে কম pf-এর জন্য বিদ্যুৎ কোম্পানি জরিমানাও করে।

সমাধান: load-এর সাথে parallel-এ একটা capacitor লাগাও। Capacitor কাছ থেকেই reactive power (−Q) দেয়, তাই source-কে কম Q দিতে হয়। P বদলায় না। Load নিজেও বদলায় না।

\[ Q_C = P\,(\tan\theta_{old} - \tan\theta_{new}) \qquad C = \frac{Q_C}{\omega V_{rms}^2} = \frac{Q_C}{2\pi f\, V_{rms}^2} \]
Worked example: A motor takes 10 kW at pf 0.8 lagging from 230 V, 50 Hz. Find the capacitor to raise pf to 0.95 lagging, and the line current before and after.

Before: S = P/pf = 10/0.8 = 12.5 kVA. Q = √(12.5² − 10²) = 7.5 kVAR. I = 12500/230 = 54.35 A.

After: θnew = cos⁻¹(0.95) = 18.19°, tan θnew = 0.3287. Qnew = 10 × 0.3287 = 3.287 kVAR.

QC = 7.5 − 3.287 = 4.213 kVAR.

C = 4213/(2π × 50 × 230²) = 4213/(314.16 × 52900) = 253.5 μF.

New S = 10/0.95 = 10.53 kVA → I = 10526/230 = 45.77 A. The current dropped by about 16% for the same 10 kW ✓.

Worked example: একটা motor 230 V, 50 Hz থেকে 0.8 lagging pf-এ 10 kW নেয়। pf 0.95 lagging করতে কত capacitor লাগবে, আর আগে-পরে line current কত?

আগে: S = P/pf = 10/0.8 = 12.5 kVA। Q = √(12.5² − 10²) = 7.5 kVAR। I = 12500/230 = 54.35 A।

পরে: θnew = cos⁻¹(0.95) = 18.19°, tan θnew = 0.3287। Qnew = 10 × 0.3287 = 3.287 kVAR।

QC = 7.5 − 3.287 = 4.213 kVAR।

C = 4213/(2π × 50 × 230²) = 4213/(314.16 × 52900) = 253.5 μF।

নতুন S = 10/0.95 = 10.53 kVA → I = 10526/230 = 45.77 A। একই 10 kW-এর জন্য current প্রায় 16% কমে গেছে ✓।

Series RLC resonanceSeries RLC resonance

In a series RLC circuit, XL grows with frequency and XC falls. At one special frequency they become equal and cancel each other. This is resonance. At resonance:

  • Z = R (the smallest possible), so the current is the largest: I = V/R.
  • The circuit is purely resistive: pf = 1, θ = 0.
  • VL and VC are equal and opposite. Each can be much bigger than the source voltage (Q times bigger).

This is how a radio "tunes" to one station: the circuit lets one frequency through strongly and blocks others.

Series RLC circuit-এ frequency বাড়লে XL বাড়ে আর XC কমে। একটা বিশেষ frequency-তে দুইটা সমান হয়ে একে অপরকে কেটে দেয়। এটাই resonance। Resonance-এ:

  • Z = R (সবচেয়ে ছোট), তাই current সবচেয়ে বেশি: I = V/R।
  • Circuit পুরোপুরি resistive: pf = 1, θ = 0।
  • VL আর VC সমান আর উল্টো। প্রতিটা source voltage-এর চেয়ে অনেক বেশি হতে পারে (Q গুণ বেশি)।

Radio এভাবেই একটা station "tune" করে: circuit একটা frequency জোরালোভাবে যেতে দেয়, বাকিগুলো আটকায়।

\[ X_L = X_C \;\Rightarrow\; \omega_0 L = \frac{1}{\omega_0 C} \;\Rightarrow\; \omega_0 = \frac{1}{\sqrt{LC}} \qquad f_0 = \frac{1}{2\pi\sqrt{LC}} \] \[ Q = \frac{\omega_0 L}{R} = \frac{1}{\omega_0 C R} = \frac{1}{R}\sqrt{\frac{L}{C}} \qquad BW = \frac{f_0}{Q} = \frac{R}{2\pi L}\ \text{(Hz)} \qquad f_{1,2} \approx f_0 \mp \frac{BW}{2} \]

Bandwidth (BW) is the width of the frequency band where the power is at least half of the peak (current ≥ 0.707 of max). f₁ and f₂ are the half-power frequencies. A high Q-factor means a narrow, sharp peak (very selective).

Bandwidth (BW) হলো সেই frequency band-এর চওড়া যেখানে power অন্তত peak-এর অর্ধেক (current ≥ max-এর 0.707)। f₁ আর f₂ হলো half-power frequency। বেশি Q-factor মানে সরু, তীক্ষ্ণ peak (খুব selective)।

Worked example: Series RLC with R = 10 Ω, L = 10 mH, C = 1 μF, fed by 10 V (RMS). Find f₀, the current at resonance, Q, BW, and VL at resonance.

LC = 0.01 × 10⁻⁶ = 10⁻⁸ → √LC = 10⁻⁴. ω₀ = 1/10⁻⁴ = 10,000 rad/s. f₀ = 10,000/(2π) = 1591.5 Hz.

At resonance Z = R = 10 Ω → I = 10/10 = 1 A (maximum).

Q = ω₀L/R = (10,000 × 0.01)/10 = 100/10 = 10.

BW = f₀/Q = 1591.5/10 = 159.2 Hz. (Check: R/(2πL) = 10/(2π × 0.01) = 159.2 Hz ✓.) So f₁ ≈ 1512 Hz, f₂ ≈ 1671 Hz. (Exact values: 1514 Hz and 1673 Hz — the "±BW/2" rule is an approximation for high Q.)

VL = I × XL = 1 × (10,000 × 0.01) = 100 V = Q × Vsource. VC is also 100 V but opposite. A 10 V source makes 100 V on the inductor!

Worked example: Series RLC: R = 10 Ω, L = 10 mH, C = 1 μF, 10 V (RMS) source। f₀, resonance-এ current, Q, BW আর resonance-এ VL বের করো।

LC = 0.01 × 10⁻⁶ = 10⁻⁸ → √LC = 10⁻⁴। ω₀ = 1/10⁻⁴ = 10,000 rad/s। f₀ = 10,000/(2π) = 1591.5 Hz।

Resonance-এ Z = R = 10 Ω → I = 10/10 = 1 A (সর্বোচ্চ)।

Q = ω₀L/R = (10,000 × 0.01)/10 = 100/10 = 10।

BW = f₀/Q = 1591.5/10 = 159.2 Hz। (Check: R/(2πL) = 10/(2π × 0.01) = 159.2 Hz ✓।) তাই f₁ ≈ 1512 Hz, f₂ ≈ 1671 Hz। (সঠিক মান: 1514 Hz আর 1673 Hz — "±BW/2" নিয়মটা বেশি Q-এর জন্য একটা আনুমানিক হিসাব।)

VL = I × XL = 1 × (10,000 × 0.01) = 100 V = Q × Vsource। VC-ও 100 V কিন্তু উল্টো। 10 V source inductor-এ 100 V তৈরি করছে!

Below f₀f₀-এর নিচেAt f₀f₀-তেAbove f₀f₀-এর উপরে
Which is biggerকোনটা বড়XC > XLXL = XCXL > XC
Circuit behaves asCircuit-এর আচরণcapacitive (I leads)resistive (pf = 1)inductive (I lags)
|Z|largeবড়minimum = Rসর্বনিম্ন = Rlargeবড়
Parallel resonance (one line): For an ideal parallel LC (tank circuit), f₀ is the same formula 1/(2π√LC), but the impedance is maximum and the line current is minimum — the opposite of series resonance. Exam MCQs love asking this difference.
Parallel resonance (এক লাইনে): আদর্শ parallel LC (tank circuit)-এ f₀-এর formula একই 1/(2π√LC), কিন্তু impedance সর্বোচ্চ আর line current সর্বনিম্ন — series resonance-এর উল্টো। Exam-এর MCQ-তে এই পার্থক্যটা খুব আসে।

Practice Questions (Admission Style)Practice Questions (Admission Style)

20 questions, from easy to hard. Q1–Q8 are short MCQs. Q9–Q20 are written/calculation problems like the IICT written test. Try each one on paper first, then open the answer. Every answer here was checked with a calculation.

২০টা প্রশ্ন, সহজ থেকে কঠিন। Q1–Q8 ছোট MCQ। Q9–Q20 হলো IICT written test-এর মতো written/calculation problem। আগে কাগজে নিজে চেষ্টা করো, তারপর উত্তর খোলো। এখানের প্রতিটা উত্তর হিসাব করে check করা।

Q1. (IICT MCQ style) A steady current of 5 A flows through a wire for 2 minutes. How much charge passes?
  • (a) 10 C
  • (b) 150 C
  • (c) 300 C
  • (d) 600 C
Q1. (IICT MCQ style) একটা wire দিয়ে 2 minute ধরে 5 A স্থির current যায়। কত charge যায়?
  • (a) 10 C
  • (b) 150 C
  • (c) 300 C
  • (d) 600 C
Show Answerউত্তর দেখুন
Answer: (d) 600 C — Q = I × t. Time must be in seconds: t = 2 × 60 = 120 s. Q = 5 × 120 = 600 C. Option (a) is the trap of using t = 2 without converting.
Answer: (d) 600 C — Q = I × t। সময় second-এ নিতে হবে: t = 2 × 60 = 120 s। Q = 5 × 120 = 600 C। Option (a) হলো convert না করে t = 2 বসানোর ফাঁদ।
Q2. (IICT MCQ style) Three 6 Ω resistors are connected in parallel. The equivalent resistance is:
  • (a) 18 Ω
  • (b) 6 Ω
  • (c) 3 Ω
  • (d) 2 Ω
Q2. (IICT MCQ style) তিনটা 6 Ω resistor parallel-এ লাগানো। Equivalent resistance কত?
  • (a) 18 Ω
  • (b) 6 Ω
  • (c) 3 Ω
  • (d) 2 Ω
Show Answerউত্তর দেখুন
Answer: (d) 2 Ω — n equal resistors R in parallel give R/n = 6/3 = 2 Ω. Also: 1/R = 1/6 + 1/6 + 1/6 = 3/6 → R = 2 Ω. 18 Ω is the series answer; 3 Ω is only two of them in parallel.
Answer: (d) 2 Ω — n টা সমান R parallel-এ দিলে R/n = 6/3 = 2 Ω। আবার: 1/R = 1/6 + 1/6 + 1/6 = 3/6 → R = 2 Ω। 18 Ω হলো series-এর উত্তর; 3 Ω হলো মাত্র দুইটা parallel-এ।
Q3. (IICT MCQ style) A 4 μF and a 12 μF capacitor are connected in series. The equivalent capacitance is:
  • (a) 16 μF
  • (b) 8 μF
  • (c) 3 μF
  • (d) 48 μF
Q3. (IICT MCQ style) একটা 4 μF আর একটা 12 μF capacitor series-এ লাগানো। Equivalent capacitance কত?
  • (a) 16 μF
  • (b) 8 μF
  • (c) 3 μF
  • (d) 48 μF
Show Answerউত্তর দেখুন
Answer: (c) 3 μF — Capacitors in series combine like resistors in parallel: C = (4 × 12)/(4 + 12) = 48/16 = 3 μF. The answer is smaller than the smallest capacitor. 16 μF would be the parallel answer — the classic trap.
Answer: (c) 3 μF — Series-এ capacitor resistor-এর parallel-এর মতো combine হয়: C = (4 × 12)/(4 + 12) = 48/16 = 3 μF। উত্তর সবচেয়ে ছোট capacitor-এর চেয়েও ছোট। 16 μF হতো parallel-এর উত্তর — এটাই পরিচিত ফাঁদ।
Q4. (IICT MCQ style) While finding the Thevenin resistance Rth, an independent voltage source is replaced by:
  • (a) an open circuit
  • (b) a short circuit
  • (c) a current source of equal value
  • (d) a resistor equal to RL
Q4. (IICT MCQ style) Thevenin resistance Rth বের করার সময় একটা independent voltage source-কে কী দিয়ে বদলানো হয়?
  • (a) open circuit
  • (b) short circuit
  • (c) সমান মানের current source
  • (d) RL-এর সমান একটা resistor
Show Answerউত্তর দেখুন
Answer: (b) short circuit — "Killing" a voltage source means setting it to 0 V. Only a plain wire has 0 V across it, so it becomes a short. A current source is killed by making it 0 A, which is an open circuit. Dependent sources are never killed.
Answer: (b) short circuit — Voltage source "kill" করা মানে এটাকে 0 V করা। শুধু একটা wire-এর উপর 0 V থাকে, তাই এটা short হয়ে যায়। Current source kill করা মানে 0 A করা, যেটা open circuit। Dependent source কখনো kill করা হয় না।
Q5. (IICT MCQ style) An RL circuit has L = 50 mH and R = 10 Ω. Its time constant is:
  • (a) 0.5 ms
  • (b) 5 ms
  • (c) 500 ms
  • (d) 0.2 s
Q5. (IICT MCQ style) একটা RL circuit-এ L = 50 mH আর R = 10 Ω। Time constant কত?
  • (a) 0.5 ms
  • (b) 5 ms
  • (c) 500 ms
  • (d) 0.2 s
Show Answerউত্তর দেখুন
Answer: (b) 5 ms — For RL, τ = L/R = 0.05/10 = 0.005 s = 5 ms. Option (c) is the trap of multiplying (L × R = 0.5 s → 500 ms); (d) is R/L = 0.2 (wrong way up).
Answer: (b) 5 ms — RL-এর জন্য τ = L/R = 0.05/10 = 0.005 s = 5 ms। Option (c) হলো গুণ করার ফাঁদ (L × R = 0.5 s → 500 ms); (d) হলো R/L = 0.2 (উল্টো ভাগ)।
Q6. (IICT MCQ style) A sinusoidal voltage has a peak value of 311 V. Its RMS value is about:
  • (a) 155.5 V
  • (b) 198 V
  • (c) 220 V
  • (d) 440 V
Q6. (IICT MCQ style) একটা sinusoidal voltage-এর peak value 311 V। এর RMS value প্রায় কত?
  • (a) 155.5 V
  • (b) 198 V
  • (c) 220 V
  • (d) 440 V
Show Answerউত্তর দেখুন
Answer: (c) 220 V — Vrms = Vm/√2 = 311/1.414 ≈ 220 V (our home supply). 198 V is the half-cycle average 2Vm/π = 0.637 × 311, a common trap. 155.5 V is Vm/2.
Answer: (c) 220 V — Vrms = Vm/√2 = 311/1.414 ≈ 220 V (আমাদের বাসার supply)। 198 V হলো half-cycle average 2Vm/π = 0.637 × 311, একটা পরিচিত ফাঁদ। 155.5 V হলো Vm/2।
Q7. (IICT MCQ style) A circuit has Vth = 16 V and Rth = 8 Ω. The maximum power it can give to a load is:
  • (a) 32 W
  • (b) 16 W
  • (c) 8 W
  • (d) 4 W
Q7. (IICT MCQ style) একটা circuit-এর Vth = 16 V আর Rth = 8 Ω। এটা load-কে সর্বোচ্চ কত power দিতে পারে?
  • (a) 32 W
  • (b) 16 W
  • (c) 8 W
  • (d) 4 W
Show Answerউত্তর দেখুন
Answer: (c) 8 W — Max power happens at RL = Rth = 8 Ω. Pmax = Vth²/(4Rth) = 256/32 = 8 W. Check: I = 16/(8 + 8) = 1 A, P = 1² × 8 = 8 W ✓. (32 W = V²/Rth, forgetting the 4.)
Answer: (c) 8 W — RL = Rth = 8 Ω হলে সর্বোচ্চ power। Pmax = Vth²/(4Rth) = 256/32 = 8 W। Check: I = 16/(8 + 8) = 1 A, P = 1² × 8 = 8 W ✓। (32 W = V²/Rth, 4 ভুলে গেলে আসে।)
Q8. (IICT MCQ style) A series RLC circuit has L = 10 mH and C = 10 μF. Its resonant frequency is closest to:
  • (a) 50 Hz
  • (b) 159 Hz
  • (c) 503 Hz
  • (d) 3162 Hz
Q8. (IICT MCQ style) একটা series RLC circuit-এ L = 10 mH আর C = 10 μF। এর resonant frequency কোনটার সবচেয়ে কাছে?
  • (a) 50 Hz
  • (b) 159 Hz
  • (c) 503 Hz
  • (d) 3162 Hz
Show Answerউত্তর দেখুন
Answer: (c) 503 Hz — LC = 0.01 × 10 × 10⁻⁶ = 10⁻⁷. √LC = 3.162 × 10⁻⁴ s. ω₀ = 1/√LC = 3162 rad/s. f₀ = ω₀/(2π) = 3162/6.283 = 503.3 Hz. Option (d) is ω₀ in rad/s — do not forget to divide by 2π for Hz.
Answer: (c) 503 Hz — LC = 0.01 × 10 × 10⁻⁶ = 10⁻⁷। √LC = 3.162 × 10⁻⁴ s। ω₀ = 1/√LC = 3162 rad/s। f₀ = ω₀/(2π) = 3162/6.283 = 503.3 Hz। Option (d) হলো rad/s-এ ω₀ — Hz পেতে 2π দিয়ে ভাগ করতে ভুলো না।
Q9. (IICT written style) An aluminium wire is 200 m long and has a diameter of 2 mm. ρ(aluminium) = 2.8 × 10⁻⁸ Ω·m. (a) Find its resistance. (b) The same wire is stretched to twice its length (volume unchanged). Find the new resistance.
Q9. (IICT written style) একটা aluminium wire 200 m লম্বা, diameter 2 mm। ρ(aluminium) = 2.8 × 10⁻⁸ Ω·m। (a) এর resistance বের করো। (b) একই wire-কে টেনে দ্বিগুণ লম্বা করা হলো (volume একই)। নতুন resistance কত?
Show Answerউত্তর দেখুন
Answer: (a) 1.78 Ω, (b) 7.13 Ω

(a) Radius r = 1 mm = 10⁻³ m. A = πr² = π × 10⁻⁶ = 3.1416 × 10⁻⁶ m².

R = ρL/A = (2.8 × 10⁻⁸ × 200)/(3.1416 × 10⁻⁶) = (5.6 × 10⁻⁶)/(3.1416 × 10⁻⁶) = 1.78 Ω.

(b) Length becomes 2L. Volume = A × L is fixed, so the area becomes A/2. New R = ρ(2L)/(A/2) = 4 × ρL/A = 4 × 1.7825 = 7.13 Ω.

Answer: (a) 1.78 Ω, (b) 7.13 Ω

(a) Radius r = 1 mm = 10⁻³ m। A = πr² = π × 10⁻⁶ = 3.1416 × 10⁻⁶ m²।

R = ρL/A = (2.8 × 10⁻⁸ × 200)/(3.1416 × 10⁻⁶) = (5.6 × 10⁻⁶)/(3.1416 × 10⁻⁶) = 1.78 Ω।

(b) দৈর্ঘ্য হয় 2L। Volume = A × L স্থির, তাই area হয় A/2। নতুন R = ρ(2L)/(A/2) = 4 × ρL/A = 4 × 1.7825 = 7.13 Ω।

Q10. (IICT written style) A 36 V source feeds a 4 Ω resistor in series with a parallel pair of 3 Ω and 6 Ω. Find (a) the equivalent resistance, (b) the source current, (c) the current in each parallel resistor, and (d) the power in each resistor. Show that power is balanced.
Q10. (IICT written style) একটা 36 V source একটা 4 Ω resistor চালায়, যার সাথে series-এ আছে 3 Ω আর 6 Ω-এর একটা parallel জোড়া। বের করো (a) equivalent resistance, (b) source current, (c) প্রতিটা parallel resistor-এর current, (d) প্রতিটা resistor-এর power। Power balance দেখাও।
Show Answerউত্তর দেখুন
Answer: Req = 6 Ω, I = 6 A, I3 = 4 A, I6 = 2 A

(a) 3 ∥ 6 = 18/9 = 2 Ω. Req = 4 + 2 = 6 Ω.

(b) I = 36/6 = 6 A.

(c) Current divider: I3 = 6 × 6/(3 + 6) = 4 A, I6 = 6 × 3/9 = 2 A. (Voltage across the pair = 6 × 2 = 12 V → 12/3 = 4 A, 12/6 = 2 A ✓.)

(d) P4Ω = 6² × 4 = 144 W, P3Ω = 4² × 3 = 48 W, P6Ω = 2² × 6 = 24 W. Total = 216 W.

Source power = 36 × 6 = 216 W ✓. Power supplied = power absorbed.

Answer: Req = 6 Ω, I = 6 A, I3 = 4 A, I6 = 2 A

(a) 3 ∥ 6 = 18/9 = 2 Ω। Req = 4 + 2 = 6 Ω।

(b) I = 36/6 = 6 A।

(c) Current divider: I3 = 6 × 6/(3 + 6) = 4 A, I6 = 6 × 3/9 = 2 A। (জোড়ার উপর voltage = 6 × 2 = 12 V → 12/3 = 4 A, 12/6 = 2 A ✓।)

(d) P4Ω = 6² × 4 = 144 W, P3Ω = 4² × 3 = 48 W, P6Ω = 2² × 6 = 24 W। মোট = 216 W।

Source power = 36 × 6 = 216 W ✓। Supplied power = absorbed power।

Q11. (IICT written style) A voltage divider has Vs = 12 V, R1 = 10 kΩ (top) and R2 = 10 kΩ (bottom). (a) Find Vout across R2 with no load. (b) Find Vout when a 10 kΩ load is connected across R2. (c) Repeat with a 100 kΩ load. What do you learn?
Q11. (IICT written style) একটা voltage divider-এ Vs = 12 V, R1 = 10 kΩ (উপরে) আর R2 = 10 kΩ (নিচে)। (a) Load ছাড়া R2-এর উপর Vout কত? (b) R2-এর উপর 10 kΩ load লাগালে Vout কত? (c) 100 kΩ load দিয়ে আবার করো। কী শিখলে?
Show Answerউত্তর দেখুন
Answer: (a) 6 V, (b) 4 V, (c) 5.71 V

(a) Vout = 12 × 10/(10 + 10) = 6 V.

(b) The load is in parallel with R2: 10 ∥ 10 = 5 kΩ. Vout = 12 × 5/(10 + 5) = 4 V.

(c) 10 ∥ 100 = 1000/110 = 9.09 kΩ. Vout = 12 × 9.09/(10 + 9.09) = 5.71 V.

Lesson: a load "pulls down" the divider output (loading effect). The bigger the load resistance compared to R2, the smaller the effect. A good rule: RL should be at least 10× R2.

Answer: (a) 6 V, (b) 4 V, (c) 5.71 V

(a) Vout = 12 × 10/(10 + 10) = 6 V।

(b) Load R2-এর সাথে parallel: 10 ∥ 10 = 5 kΩ। Vout = 12 × 5/(10 + 5) = 4 V।

(c) 10 ∥ 100 = 1000/110 = 9.09 kΩ। Vout = 12 × 9.09/(10 + 9.09) = 5.71 V।

শিক্ষা: Load লাগালে divider-এর output "নেমে যায়" (loading effect)। R2-এর তুলনায় load resistance যত বড়, প্রভাব তত কম। ভালো নিয়ম: RL অন্তত R2-এর 10 গুণ হওয়া উচিত।

Q12. (IICT written style) In a Wheatstone bridge, P = 10 Ω (A–C), Q = 20 Ω (C–B), R = 30 Ω (A–D) and X (D–B) is unknown. A 50 Ω galvanometer is connected between C and D. (a) Find X for balance. (b) With this X, find the equivalent resistance between A and B.
Q12. (IICT written style) একটা Wheatstone bridge-এ P = 10 Ω (A–C), Q = 20 Ω (C–B), R = 30 Ω (A–D), আর X (D–B) অজানা। C আর D-এর মাঝে একটা 50 Ω galvanometer। (a) Balance-এর জন্য X কত? (b) এই X নিয়ে A আর B-এর মাঝে equivalent resistance কত?
Show Answerউত্তর দেখুন
Answer: (a) X = 60 Ω, (b) RAB = 22.5 Ω

(a) Balance: P/Q = R/X → X = QR/P = (20 × 30)/10 = 60 Ω. Check: 10/20 = 30/60 = 0.5 ✓.

(b) At balance VC = VD, so no current flows in the 50 Ω galvanometer. Remove it. Now we have two parallel paths: A–C–B = 10 + 20 = 30 Ω and A–D–B = 30 + 60 = 90 Ω.

RAB = 30 ∥ 90 = 2700/120 = 22.5 Ω. (A full nodal solution with the 50 Ω in place gives the same 22.5 Ω ✓.)

Answer: (a) X = 60 Ω, (b) RAB = 22.5 Ω

(a) Balance: P/Q = R/X → X = QR/P = (20 × 30)/10 = 60 Ω। Check: 10/20 = 30/60 = 0.5 ✓।

(b) Balance-এ VC = VD, তাই 50 Ω galvanometer দিয়ে current যায় না। এটা সরিয়ে দিই। এখন দুইটা parallel পথ: A–C–B = 10 + 20 = 30 Ω আর A–D–B = 30 + 60 = 90 Ω।

RAB = 30 ∥ 90 = 2700/120 = 22.5 Ω। (50 Ω রেখে পুরো nodal solve করলেও একই 22.5 Ω আসে ✓।)

Q13. (IICT written style) Find the equivalent resistance between A and B of the bridge below. (A–C = 10 Ω, C–B = 20 Ω, A–D = 20 Ω, D–B = 10 Ω, C–D = 10 Ω.) Use Δ–Y conversion.
Q13. (IICT written style) নিচের bridge-এর A আর B-এর মাঝে equivalent resistance বের করো। (A–C = 10 Ω, C–B = 20 Ω, A–D = 20 Ω, D–B = 10 Ω, C–D = 10 Ω।) Δ–Y conversion ব্যবহার করো।
10 Ω20 Ω20 Ω10 Ω10 ΩABCD
Q13: an unbalanced bridge (10/20 ≠ 20/10).Q13: একটা unbalanced bridge (10/20 ≠ 20/10)।
Show Answerউত্তর দেখুন
Answer: RAB = 14 Ω

Step 1 — check balance: P/Q = 10/20 = 0.5, R/X = 20/10 = 2. Not equal → the middle 10 Ω carries current. We cannot remove it.

Step 2 — take the Δ formed by A, C, D: sides AC = 10, CD = 10, DA = 20. Sum = 40 Ω.

Step 3 — convert to Y with centre O:

  • RA = (AC × AD)/40 = (10 × 20)/40 = 5 Ω
  • RC = (AC × CD)/40 = (10 × 10)/40 = 2.5 Ω
  • RD = (AD × CD)/40 = (20 × 10)/40 = 5 Ω

Step 4 — now the network is: A –5 Ω– O, then two parallel paths from O to B: O–C–B = 2.5 + 20 = 22.5 Ω, and O–D–B = 5 + 10 = 15 Ω.

22.5 ∥ 15 = 337.5/37.5 = 9 Ω. So RAB = 5 + 9 = 14 Ω.

(Checked by nodal analysis with 1 A injected at A: VA = 14 V ✓.)

Answer: RAB = 14 Ω

Step 1 — balance check: P/Q = 10/20 = 0.5, R/X = 20/10 = 2। সমান না → মাঝের 10 Ω দিয়ে current যায়। এটা সরানো যাবে না।

Step 2 — A, C, D দিয়ে তৈরি Δ নিই: side AC = 10, CD = 10, DA = 20। যোগফল = 40 Ω।

Step 3 — centre O নিয়ে Y-তে convert করি:

  • RA = (AC × AD)/40 = (10 × 20)/40 = 5 Ω
  • RC = (AC × CD)/40 = (10 × 10)/40 = 2.5 Ω
  • RD = (AD × CD)/40 = (20 × 10)/40 = 5 Ω

Step 4 — এখন network: A –5 Ω– O, তারপর O থেকে B পর্যন্ত দুইটা parallel পথ: O–C–B = 2.5 + 20 = 22.5 Ω, আর O–D–B = 5 + 10 = 15 Ω।

22.5 ∥ 15 = 337.5/37.5 = 9 Ω। তাই RAB = 5 + 9 = 14 Ω।

(A-তে 1 A ঢুকিয়ে nodal analysis দিয়ে check করা: VA = 14 V ✓।)

Q14. (IICT written style) Use nodal analysis to find V1 and V2 in the circuit below. Then find the current supplied by the 12 V source. (A 4 A source feeds node 1; 2 Ω from node 1 to ground; 4 Ω between the nodes; 3 Ω from node 2 to ground; the 12 V source connects to node 2 through 6 Ω.)
Q14. (IICT written style) Nodal analysis দিয়ে নিচের circuit-এর V1 আর V2 বের করো। তারপর 12 V source কত current দেয় বের করো। (একটা 4 A source node 1-এ current দেয়; node 1 থেকে ground-এ 2 Ω; দুই node-এর মাঝে 4 Ω; node 2 থেকে ground-এ 3 Ω; 12 V source 6 Ω দিয়ে node 2-এ যুক্ত।)
4 A2 Ω4 Ω3 Ω6 Ω+−12 VV1V2
Q14: two unknown node voltages V1 and V2.Q14: দুইটা অজানা node voltage V1 আর V2।
Show Answerউত্তর দেখুন
Answer: V1 = 7 V, V2 = 5 V, I12V = 1.17 A

KCL at node 1 (leaving through resistors = 4 A entering): V1/2 + (V1 − V2)/4 = 4. Multiply by 4: 2V1 + V1 − V2 = 16 → 3V1 − V2 = 16 ...(1)

KCL at node 2: (V2 − V1)/4 + V2/3 + (V2 − 12)/6 = 0. Multiply by 12: 3V2 − 3V1 + 4V2 + 2V2 − 24 = 0 → −3V1 + 9V2 = 24 → −V1 + 3V2 = 8 ...(2)

Solve: from (2), V1 = 3V2 − 8. Put in (1): 3(3V2 − 8) − V2 = 16 → 9V2 − 24 − V2 = 16 → 8V2 = 40 → V2 = 5 V. V1 = 15 − 8 = 7 V.

12 V source current = (12 − V2)/6 = 7/6 = 1.17 A (into node 2).

Check node 2: in = 0.5 A (from the 4 Ω: (7 − 5)/4) + 1.167 A = 1.667 A. Out through 3 Ω = 5/3 = 1.667 A ✓.

Answer: V1 = 7 V, V2 = 5 V, I12V = 1.17 A

Node 1-এ KCL (resistor দিয়ে বের হওয়া = ঢোকা 4 A): V1/2 + (V1 − V2)/4 = 4। 4 দিয়ে গুণ: 2V1 + V1 − V2 = 16 → 3V1 − V2 = 16 ...(1)

Node 2-এ KCL: (V2 − V1)/4 + V2/3 + (V2 − 12)/6 = 0। 12 দিয়ে গুণ: 3V2 − 3V1 + 4V2 + 2V2 − 24 = 0 → −3V1 + 9V2 = 24 → −V1 + 3V2 = 8 ...(2)

Solve: (2) থেকে V1 = 3V2 − 8। (1)-এ বসাই: 3(3V2 − 8) − V2 = 16 → 9V2 − 24 − V2 = 16 → 8V2 = 40 → V2 = 5 V। V1 = 15 − 8 = 7 V।

12 V source-এর current = (12 − V2)/6 = 7/6 = 1.17 A (node 2-এ ঢোকে)।

Node 2 check: ঢোকে = 0.5 A (4 Ω থেকে: (7 − 5)/4) + 1.167 A = 1.667 A। 3 Ω দিয়ে বের হয় = 5/3 = 1.667 A ✓।

Q15. (IICT written style) Use mesh analysis on the circuit below to find I1, I2, the current in the 6 Ω resistor, and the power of each source. Verify the power balance.
Q15. (IICT written style) নিচের circuit-এ mesh analysis দিয়ে I1, I2, 6 Ω resistor-এর current আর প্রতিটা source-এর power বের করো। Power balance যাচাই করো।
+−20 V2 Ω6 Ω1 Ω+−10 VI1I2
Q15: two meshes; the 6 Ω resistor is shared.Q15: দুইটা mesh; 6 Ω resistor দুইজনের shared।
Show Answerউত্তর দেখুন
Answer: I1 = 4 A, I2 = 2 A, I6Ω = 2 A (down)

Mesh 1: 20 − 2I1 − 6(I1 − I2) = 0 → 8I1 − 6I2 = 20 ...(1)

Mesh 2: −6(I2 − I1) − 1·I2 − 10 = 0 → 6I1 − 7I2 = 10 → −6I1 + 7I2 = −10 ...(2)

Cramer: Δ = 8·7 − (−6)(−6) = 56 − 36 = 20.

I1 = (20·7 − (−6)(−10))/20 = (140 − 60)/20 = 4 A. I2 = (8·(−10) − (−6)·20)/20 = (−80 + 120)/20 = 2 A.

Current in 6 Ω = I1 − I2 = 2 A downward.

Powers: 20 V source: 4 A leaves its + → supplies 20 × 4 = 80 W. 10 V source: 2 A enters its + terminal → absorbs 10 × 2 = 20 W. Resistors: 2 × 4² + 1 × 2² + 6 × 2² = 32 + 4 + 24 = 60 W.

Balance: 80 W supplied = 60 W + 20 W absorbed ✓.

Answer: I1 = 4 A, I2 = 2 A, I6Ω = 2 A (নিচের দিকে)

Mesh 1: 20 − 2I1 − 6(I1 − I2) = 0 → 8I1 − 6I2 = 20 ...(1)

Mesh 2: −6(I2 − I1) − 1·I2 − 10 = 0 → 6I1 − 7I2 = 10 → −6I1 + 7I2 = −10 ...(2)

Cramer: Δ = 8·7 − (−6)(−6) = 56 − 36 = 20।

I1 = (20·7 − (−6)(−10))/20 = (140 − 60)/20 = 4 A। I2 = (8·(−10) − (−6)·20)/20 = (−80 + 120)/20 = 2 A।

6 Ω-এর current = I1 − I2 = 2 A নিচের দিকে।

Power: 20 V source: 4 A এর + দিয়ে বের হয় → 20 × 4 = 80 W supply। 10 V source: 2 A এর + terminal দিয়ে ঢোকে → 10 × 2 = 20 W absorb। Resistor: 2 × 4² + 1 × 2² + 6 × 2² = 32 + 4 + 24 = 60 W।

Balance: 80 W supplied = 60 W + 20 W absorbed ✓।

Q16. (IICT written style) A 10 V source with 2 Ω in series and a 20 V source with 4 Ω in series both feed the same top node. A 4 Ω resistor goes from that node to ground (the bottom of both sources is ground). Using superposition, find the current in the 4 Ω load resistor and its power.
Q16. (IICT written style) একটা 10 V source (series-এ 2 Ω) আর একটা 20 V source (series-এ 4 Ω) দুইটাই একই উপরের node-এ যুক্ত। ওই node থেকে ground-এ একটা 4 Ω resistor (দুই source-এর নিচের দিক ground)। Superposition দিয়ে 4 Ω load resistor-এর current আর power বের করো।
Show Answerউত্তর দেখুন
Answer: I = 2.5 A, P = 25 W

Only 10 V (20 V → short): the 4 Ω (source branch) and the 4 Ω load are in parallel = 2 Ω. Node voltage V′ = 10 × 2/(2 + 2) = 5 V. I′ = 5/4 = 1.25 A.

Only 20 V (10 V → short): the 2 Ω and the 4 Ω load are in parallel = 8/6 = 4/3 Ω. V″ = 20 × (4/3)/(4 + 4/3) = 20 × (4/3)/(16/3) = 20 × 0.25 = 5 V. I″ = 5/4 = 1.25 A.

Total: I = 1.25 + 1.25 = 2.5 A (node voltage = 10 V). P = 2.5² × 4 = 25 W.

Nodal check: (V − 10)/2 + (V − 20)/4 + V/4 = 0 → ×4: 2V − 20 + V − 20 + V = 0 → V = 10 V ✓.

Note: power from each source alone would be 1.25² × 4 = 6.25 W each (sum 12.5 W) — wrong. Always add currents first.

Answer: I = 2.5 A, P = 25 W

শুধু 10 V (20 V → short): source branch-এর 4 Ω আর 4 Ω load parallel = 2 Ω। Node voltage V′ = 10 × 2/(2 + 2) = 5 V। I′ = 5/4 = 1.25 A।

শুধু 20 V (10 V → short): 2 Ω আর 4 Ω load parallel = 8/6 = 4/3 Ω। V″ = 20 × (4/3)/(4 + 4/3) = 20 × (4/3)/(16/3) = 20 × 0.25 = 5 V। I″ = 5/4 = 1.25 A।

মোট: I = 1.25 + 1.25 = 2.5 A (node voltage = 10 V)। P = 2.5² × 4 = 25 W।

Nodal check: (V − 10)/2 + (V − 20)/4 + V/4 = 0 → ×4: 2V − 20 + V − 20 + V = 0 → V = 10 V ✓।

খেয়াল করো: প্রতিটা source একা যে power দেয় = 1.25² × 4 = 6.25 W করে (যোগ 12.5 W) — ভুল। আগে সবসময় current যোগ করো।

Q17. (IICT written style) For the circuit below, find the Thevenin and Norton equivalents at terminals x–y. What load RL gets maximum power, and what is that power?
Q17. (IICT written style) নিচের circuit-এর terminal x–y-তে Thevenin আর Norton equivalent বের করো। কোন load RL সর্বোচ্চ power পাবে, আর সেই power কত?
+−30 V6 Ω2 A12 Ω4 Ωnode axyRL goes here
Q17: a voltage source and a current source feeding node a; the load connects at x–y.Q17: একটা voltage source আর একটা current source node a-তে যুক্ত; load লাগবে x–y-তে।
Show Answerউত্তর দেখুন
Answer: Vth = 28 V, Rth = 8 Ω, IN = 3.5 A, RL = 8 Ω, Pmax = 24.5 W

Vth: with x–y open, no current in the 4 Ω, so Vth = Va. KCL at a: (Va − 30)/6 + Va/12 = 2. Multiply by 12: 2Va − 60 + Va = 24 → 3Va = 84 → Vth = 28 V.

(Superposition check: 30 V alone → 30 × 12/18 = 20 V; 2 A alone → 2 × (6 ∥ 12) = 2 × 4 = 8 V; total 28 V ✓.)

Rth: kill sources: 30 V → short, 2 A → open. Looking in from x–y: 4 + (6 ∥ 12) = 4 + 4 = 8 Ω.

Norton: IN = 28/8 = 3.5 A, RN = 8 Ω. (Direct check: short x–y: (Va − 30)/6 + Va/12 + Va/4 = 2 → ×12: 6Va = 84 → Va = 14 V → Isc = 14/4 = 3.5 A ✓.)

Max power: RL = Rth = 8 Ω. Pmax = 28²/(4 × 8) = 784/32 = 24.5 W. (Load current = 28/16 = 1.75 A; 1.75² × 8 = 24.5 W ✓.)

Answer: Vth = 28 V, Rth = 8 Ω, IN = 3.5 A, RL = 8 Ω, Pmax = 24.5 W

Vth: x–y open থাকলে 4 Ω দিয়ে current নেই, তাই Vth = Va। a-তে KCL: (Va − 30)/6 + Va/12 = 2। 12 দিয়ে গুণ: 2Va − 60 + Va = 24 → 3Va = 84 → Vth = 28 V।

(Superposition check: শুধু 30 V → 30 × 12/18 = 20 V; শুধু 2 A → 2 × (6 ∥ 12) = 2 × 4 = 8 V; মোট 28 V ✓।)

Rth: source kill: 30 V → short, 2 A → open। x–y থেকে দেখলে: 4 + (6 ∥ 12) = 4 + 4 = 8 Ω।

Norton: IN = 28/8 = 3.5 A, RN = 8 Ω। (সরাসরি check: x–y short: (Va − 30)/6 + Va/12 + Va/4 = 2 → ×12: 6Va = 84 → Va = 14 V → Isc = 14/4 = 3.5 A ✓।)

Max power: RL = Rth = 8 Ω। Pmax = 28²/(4 × 8) = 784/32 = 24.5 W। (Load current = 28/16 = 1.75 A; 1.75² × 8 = 24.5 W ✓।)

Q18. (IICT written style) An uncharged 50 μF capacitor is charged from a 100 V DC source through a 20 kΩ resistor. Find: (a) τ, (b) the initial current, (c) vC at t = 1 s and t = 3 s, (d) the time for vC to reach 50 V and 90 V, (e) the final stored energy.
Q18. (IICT written style) একটা খালি 50 μF capacitor-কে 20 kΩ resistor দিয়ে 100 V DC source থেকে charge করা হচ্ছে। বের করো: (a) τ, (b) শুরুর current, (c) t = 1 s আর t = 3 s-এ vC, (d) vC 50 V আর 90 V হতে কত সময়, (e) শেষে জমা energy।
Show Answerউত্তর দেখুন
Answer: τ = 1 s, i(0) = 5 mA, v(1) = 63.2 V, v(3) = 95.0 V, t50 = 0.693 s, t90 = 2.30 s, W = 0.25 J

(a) τ = RC = 20 × 10³ × 50 × 10⁻⁶ = 1 s.

(b) At t = 0 the capacitor is like a short: i(0) = 100/20,000 = 5 mA.

(c) v(t) = 100(1 − e−t). v(1) = 100 × 0.632 = 63.2 V. v(3) = 100 × 0.950 = 95.0 V.

(d) 50 = 100(1 − e−t) → e−t = 0.5 → t = ln 2 = 0.693 s. 90 = 100(1 − e−t) → e−t = 0.1 → t = ln 10 = 2.30 s.

(e) W = ½CV² = ½ × 50 × 10⁻⁶ × 100² = 0.25 J. (Fun fact: the resistor also burns exactly 0.25 J during charging — the charging efficiency is always 50%.)

Answer: τ = 1 s, i(0) = 5 mA, v(1) = 63.2 V, v(3) = 95.0 V, t50 = 0.693 s, t90 = 2.30 s, W = 0.25 J

(a) τ = RC = 20 × 10³ × 50 × 10⁻⁶ = 1 s।

(b) t = 0-তে capacitor short-এর মতো: i(0) = 100/20,000 = 5 mA।

(c) v(t) = 100(1 − e−t)। v(1) = 100 × 0.632 = 63.2 V। v(3) = 100 × 0.950 = 95.0 V।

(d) 50 = 100(1 − e−t) → e−t = 0.5 → t = ln 2 = 0.693 s। 90 = 100(1 − e−t) → e−t = 0.1 → t = ln 10 = 2.30 s।

(e) W = ½CV² = ½ × 50 × 10⁻⁶ × 100² = 0.25 J। (মজার তথ্য: charging-এর সময় resistor-ও ঠিক 0.25 J খরচ করে — charging efficiency সবসময় 50%।)

Q19. (IICT written style) A series load has R = 8 Ω, XL = 10 Ω and XC = 4 Ω. It is connected to 230 V (RMS), 50 Hz. Find: (a) Z in polar form, (b) the current and its phase, (c) P, Q, S and pf, (d) the capacitor to connect in parallel to make pf = 1, and the new line current.
Q19. (IICT written style) একটা series load-এ R = 8 Ω, XL = 10 Ω আর XC = 4 Ω। এটা 230 V (RMS), 50 Hz-এ লাগানো। বের করো: (a) polar form-এ Z, (b) current আর তার phase, (c) P, Q, S আর pf, (d) pf = 1 করতে parallel-এ কত capacitor লাগবে, আর নতুন line current।
Show Answerউত্তর দেখুন
Answer: Z = 10∠36.87° Ω, I = 23∠−36.87° A, P = 4232 W, Q = 3174 VAR, S = 5290 VA, pf = 0.8 lagging, C = 191 μF, new I = 18.4 A

(a) Z = 8 + j(10 − 4) = 8 + j6. |Z| = √(64 + 36) = 10 Ω. θ = tan⁻¹(6/8) = 36.87°. So Z = 10∠36.87° Ω.

(b) I = 230∠0°/10∠36.87° = 23∠−36.87° A → the current lags by 36.87° (inductive load).

(c) pf = cos 36.87° = 0.8 lagging. P = I²R = 23² × 8 = 529 × 8 = 4232 W. Q = I²X = 529 × 6 = 3174 VAR. S = VI = 230 × 23 = 5290 VA. Check: √(4232² + 3174²) = 5290 ✓.

(d) For pf = 1 the capacitor must supply all Q: QC = 3174 VAR. C = QC/(ωV²) = 3174/(314.16 × 230²) = 3174/(314.16 × 52900) = 191 μF.

New line current = P/V = 4232/230 = 18.4 A (down from 23 A). The load still takes 23 A, but the capacitor now supplies the reactive part locally.

Answer: Z = 10∠36.87° Ω, I = 23∠−36.87° A, P = 4232 W, Q = 3174 VAR, S = 5290 VA, pf = 0.8 lagging, C = 191 μF, নতুন I = 18.4 A

(a) Z = 8 + j(10 − 4) = 8 + j6। |Z| = √(64 + 36) = 10 Ω। θ = tan⁻¹(6/8) = 36.87°। তাই Z = 10∠36.87° Ω।

(b) I = 230∠0°/10∠36.87° = 23∠−36.87° A → current 36.87° পিছিয়ে (inductive load)।

(c) pf = cos 36.87° = 0.8 lagging। P = I²R = 23² × 8 = 529 × 8 = 4232 W। Q = I²X = 529 × 6 = 3174 VAR। S = VI = 230 × 23 = 5290 VA। Check: √(4232² + 3174²) = 5290 ✓।

(d) pf = 1 করতে capacitor-কে পুরো Q দিতে হবে: QC = 3174 VAR। C = QC/(ωV²) = 3174/(314.16 × 230²) = 3174/(314.16 × 52900) = 191 μF।

নতুন line current = P/V = 4232/230 = 18.4 A (23 A থেকে কমেছে)। Load নিজে এখনো 23 A নেয়, কিন্তু reactive অংশটা এখন capacitor কাছ থেকেই দেয়।

Q20. (IICT written style) A series RLC circuit has R = 5 Ω, L = 50 mH and C = 0.2 μF. It is driven by a 2 V (RMS) source of variable frequency. Find: (a) the resonant frequency f₀, (b) the current at resonance, (c) the Q-factor and bandwidth, (d) the capacitor voltage at resonance, (e) the capacitance needed (same L) to resonate at 1 kHz instead.
Q20. (IICT written style) একটা series RLC circuit-এ R = 5 Ω, L = 50 mH আর C = 0.2 μF। এটা পরিবর্তনশীল frequency-র 2 V (RMS) source দিয়ে চালানো। বের করো: (a) resonant frequency f₀, (b) resonance-এ current, (c) Q-factor আর bandwidth, (d) resonance-এ capacitor voltage, (e) একই L রেখে 1 kHz-এ resonance চাইলে কত capacitance লাগবে।
Show Answerউত্তর দেখুন
Answer: f₀ = 1591.5 Hz, I = 0.4 A, Q = 100, BW = 15.9 Hz, VC = 200 V, Cnew = 0.507 μF

(a) LC = 0.05 × 0.2 × 10⁻⁶ = 10⁻⁸ → √LC = 10⁻⁴. ω₀ = 10,000 rad/s. f₀ = 10,000/(2π) = 1591.5 Hz.

(b) At resonance Z = R = 5 Ω → I = 2/5 = 0.4 A.

(c) Q = (1/R)√(L/C) = (1/5)√(0.05/(0.2 × 10⁻⁶)) = (1/5)√250,000 = 500/5 = 100. BW = f₀/Q = 1591.5/100 = 15.9 Hz (a very sharp, selective circuit).

(d) XC = XL = ω₀L = 10,000 × 0.05 = 500 Ω. VC = 0.4 × 500 = 200 V = Q × Vsource = 100 × 2 ✓. A 2 V source makes 200 V on the capacitor — the capacitor must be rated for this!

(e) C = 1/((2πf)²L) = 1/((2π × 1000)² × 0.05) = 1/(3.948 × 10⁷ × 0.05) = 1/(1.974 × 10⁶) = 0.507 μF. (Lower frequency → bigger C, since f₀ ∝ 1/√C ✓.)

Answer: f₀ = 1591.5 Hz, I = 0.4 A, Q = 100, BW = 15.9 Hz, VC = 200 V, Cnew = 0.507 μF

(a) LC = 0.05 × 0.2 × 10⁻⁶ = 10⁻⁸ → √LC = 10⁻⁴। ω₀ = 10,000 rad/s। f₀ = 10,000/(2π) = 1591.5 Hz।

(b) Resonance-এ Z = R = 5 Ω → I = 2/5 = 0.4 A।

(c) Q = (1/R)√(L/C) = (1/5)√(0.05/(0.2 × 10⁻⁶)) = (1/5)√250,000 = 500/5 = 100। BW = f₀/Q = 1591.5/100 = 15.9 Hz (খুব তীক্ষ্ণ, selective circuit)।

(d) XC = XL = ω₀L = 10,000 × 0.05 = 500 Ω। VC = 0.4 × 500 = 200 V = Q × Vsource = 100 × 2 ✓। 2 V source capacitor-এ 200 V তৈরি করে — capacitor-এর rating এর জন্য যথেষ্ট হতে হবে!

(e) C = 1/((2πf)²L) = 1/((2π × 1000)² × 0.05) = 1/(3.948 × 10⁷ × 0.05) = 1/(1.974 × 10⁶) = 0.507 μF। (কম frequency → বড় C, কারণ f₀ ∝ 1/√C ✓।)