Electronic DevicesElectronic Devices

From sand to chips — semiconductors, diodes, rectifiers, Zener and special diodes, BJT, MOSFET, CMOS and op-amps, with many solved numbers. Sand থেকে chip পর্যন্ত — semiconductor, diode, rectifier, Zener আর special diode, BJT, MOSFET, CMOS আর op-amp, অনেক solved math সহ।

Who is this chapter for? This chapter is for the BUET IICT admission test (MSc in ICT / MSc in Information Security). Electronic Devices is part of the compulsory MCQ test, and it is also an optional topic in the ICT written test. It is written for a reader from a CS background, so we start from zero. You do not need any earlier electronics knowledge. Just read slowly, and do every worked example with a pen.
এই chapter কার জন্য? এই chapter BUET IICT admission test-এর জন্য (MSc in ICT / MSc in Information Security)। Electronic Devices compulsory MCQ test-এর অংশ, আর ICT written test-এ এটা একটা optional topic। CS background-এর reader-এর জন্য লেখা, তাই আমরা একদম শূন্য থেকে শুরু করব। আগে electronics জানার দরকার নেই। ধীরে ধীরে পড়ো, আর প্রতিটা worked example খাতা-কলমে নিজে করো।

1. Semiconductor Basics1. Semiconductor Basics

Every chip in your laptop is made from a semiconductor, mostly silicon (Si). To understand diodes and transistors, we first need to know why silicon is special.

Materials can be put into three groups by how well they carry current:

  • Conductor — carries current very easily. Example: copper, aluminium, silver.
  • Insulator — almost no current flows. Example: glass, rubber, diamond, SiO₂.
  • Semiconductor — in between. Pure silicon carries only a little current. But we can control it a lot by adding tiny amounts of other atoms, by heat, or by light. Example: silicon (Si), germanium (Ge), gallium arsenide (GaAs).

Silicon and germanium are in group IV of the periodic table. Each atom has 4 valence electrons. In a crystal, each atom shares these 4 electrons with 4 neighbours. These shared pairs are called covalent bonds.

তোমার laptop-এর প্রতিটা chip একটা semiconductor দিয়ে তৈরি, বেশিরভাগ সময় silicon (Si)। Diode আর transistor বুঝতে হলে আগে জানতে হবে silicon কেন special।

Current কতটা সহজে চলে, সেই হিসেবে material-কে তিন ভাগে ভাগ করা যায়:

  • Conductor — খুব সহজে current চলে। যেমন: copper, aluminium, silver।
  • Insulator — প্রায় কোনো current চলে না। যেমন: glass, rubber, diamond, SiO₂।
  • Semiconductor — মাঝামাঝি। Pure silicon-এ অল্প current চলে। কিন্তু সামান্য অন্য atom মিশিয়ে, তাপ দিয়ে বা আলো দিয়ে একে অনেক control করা যায়। যেমন: silicon (Si), germanium (Ge), gallium arsenide (GaAs)।

Silicon আর germanium periodic table-এর group IV-তে আছে। প্রতিটা atom-এর 4টা valence electron থাকে। Crystal-এ প্রতিটা atom তার 4টা electron পাশের 4টা atom-এর সাথে share করে। এই shared জোড়াগুলোকে বলে covalent bond।

Energy Band PictureEnergy Band-এর ধারণা

In a solid, electron energies group into bands. Two bands matter for us:

  • Valence band (VB) — electrons here are stuck in bonds. They cannot move freely.
  • Conduction band (CB) — electrons here are free. They can move and carry current.
  • Band gap (Eg) — the empty energy gap between VB and CB. No electron can sit inside the gap. An electron needs at least Eg energy to jump from VB to CB.

Energy is measured in electron-volts (eV). 1 eV = 1.6 × 10⁻¹⁹ J. It is the energy one electron gains when it moves through 1 volt.

Now the three groups are easy to explain:

  • Conductor: the bands overlap (no gap). Free electrons are always there.
  • Semiconductor: small gap (about 1 eV). At room temperature, heat gives a few electrons enough energy to jump. So a little current can flow.
  • Insulator: big gap (more than about 5 eV; diamond ≈ 5.5 eV). Almost no electron can jump.

Solid-এ electron-এর energy গুলো কিছু band-এ ভাগ হয়ে থাকে। আমাদের দরকার দুইটা band:

  • Valence band (VB) — এখানের electron bond-এ আটকে থাকে। স্বাধীনভাবে চলতে পারে না।
  • Conduction band (CB) — এখানের electron free। এরা চলতে পারে আর current বহন করে।
  • Band gap (Eg) — VB আর CB-এর মাঝের খালি energy gap। Gap-এর ভেতরে কোনো electron থাকতে পারে না। VB থেকে CB-তে লাফ দিতে electron-এর কমপক্ষে Eg energy লাগে।

Energy মাপা হয় electron-volt (eV) দিয়ে। 1 eV = 1.6 × 10⁻¹⁹ J। একটা electron 1 volt পার হলে যতটুকু energy পায়, সেটাই 1 eV।

এখন তিনটা group সহজে বোঝা যায়:

  • Conductor: band দুইটা overlap করে (কোনো gap নেই)। Free electron সবসময় থাকে।
  • Semiconductor: ছোট gap (প্রায় 1 eV)। Room temperature-এ তাপ থেকে কিছু electron লাফ দেওয়ার মতো energy পায়। তাই অল্প current চলে।
  • Insulator: বড় gap (প্রায় 5 eV-এর বেশি; diamond ≈ 5.5 eV)। প্রায় কোনো electron লাফ দিতে পারে না।
Energy Conduction band Valence band overlap Conductor CB VB Eg ≈ 1 eV (Si 1.1) Semiconductor CB VB Eg > 5 eV Insulator
Energy bands. In a semiconductor, heat pushes a few electrons (blue dot) up to the CB and leaves a hole (open circle) in the VB.Energy band। Semiconductor-এ তাপ কিছু electron (নীল বিন্দু) CB-তে তুলে দেয় আর VB-তে একটা hole (ফাঁকা বৃত্ত) রেখে যায়।
MaterialMaterialBand gap at 300 K300 K-এ Band gapWhere usedকোথায় ব্যবহার
Germanium (Ge)0.67 eVOld diodes and transistors. Small barrier, but high leakage.পুরনো diode আর transistor। Barrier ছোট, কিন্তু leakage বেশি।
Silicon (Si)1.1 eVAlmost all ICs, CPUs, memory, diodes, solar cells.প্রায় সব IC, CPU, memory, diode, solar cell।
Gallium arsenide (GaAs)1.43 eVLEDs, lasers, very high-frequency (RF) chips.LED, laser, খুব high-frequency (RF) chip।
Band filling in metals, semimetals, semiconductors and insulators
A real textbook-style band picture: metal, semimetal, semiconductor and insulator. Look at the size of the gap. (Wikimedia Commons)Textbook-এর মতো একটা আসল band picture: metal, semimetal, semiconductor আর insulator। Gap-এর size খেয়াল করো। (Wikimedia Commons)
Example (band gap → light colour): When an electron falls from CB to VB, it can give out light. The wavelength is about λ (µm) ≈ 1.24 / Eg(eV).

Si: λ ≈ 1.24 / 1.1 = 1.13 µm (infrared, we cannot see it). GaAs: λ ≈ 1.24 / 1.43 = 0.867 µm = 867 nm (near infrared). This is why TV remote LEDs use GaAs, and why plain silicon is not used for LEDs.

Example (band gap → আলোর রং): একটা electron CB থেকে VB-তে পড়লে আলো বের হতে পারে। Wavelength প্রায় λ (µm) ≈ 1.24 / Eg(eV)।

Si: λ ≈ 1.24 / 1.1 = 1.13 µm (infrared, চোখে দেখা যায় না)। GaAs: λ ≈ 1.24 / 1.43 = 0.867 µm = 867 nm (near infrared)। এই কারণে TV remote-এর LED-তে GaAs ব্যবহার হয়, আর সাধারণ silicon দিয়ে LED বানানো হয় না।

Electrons and HolesElectron আর Hole

When an electron jumps to the CB, it leaves an empty spot in the VB. This empty spot is called a hole. A hole acts like a positive charge. A nearby electron can fill it, and then the hole "moves" to where that electron came from. So current in a semiconductor is carried by two kinds of carriers: free electrons (negative) and holes (positive).

Think of a parking lot with one empty slot. Cars move forward one by one to fill it, and the empty slot seems to move backward. The empty slot is the hole.

একটা electron CB-তে লাফ দিলে VB-তে একটা খালি জায়গা রেখে যায়। এই খালি জায়গাকে বলে hole। Hole একটা positive charge-এর মতো আচরণ করে। পাশের একটা electron এসে এটা পূরণ করতে পারে, তখন hole "সরে যায়" ওই electron যেখান থেকে এসেছিল সেখানে। তাই semiconductor-এ current বহন করে দুই ধরনের carrier: free electron (negative) আর hole (positive)।

একটা parking lot ভাবো যেখানে একটা slot খালি। গাড়িগুলো একটা একটা করে সামনে এগিয়ে slot পূরণ করে, আর খালি slot-টা পেছনের দিকে সরে যায় মনে হয়। ওই খালি slot-টাই hole।

Intrinsic vs Extrinsic SemiconductorIntrinsic বনাম Extrinsic Semiconductor

  • Intrinsic = pure semiconductor. Every electron that jumps makes one hole. So electrons = holes: n = p = ni. Here ni is the intrinsic carrier concentration. For Si at 300 K, ni ≈ 1.5 × 10¹⁰ cm⁻³ (some books use 1 × 10¹⁰). That is very small, because Si has about 5 × 10²² atoms per cm³.
  • Extrinsic = doped semiconductor. We add a tiny amount of impurity atoms. This is called doping. Even 1 impurity atom per million Si atoms changes the conductivity by a huge amount.
  • Intrinsic = pure semiconductor। যতগুলো electron লাফ দেয়, ততগুলো hole তৈরি হয়। তাই electron = hole: n = p = ni। এখানে ni হলো intrinsic carrier concentration। 300 K-এ Si-এর জন্য ni ≈ 1.5 × 10¹⁰ cm⁻³ (কিছু বইয়ে 1 × 10¹⁰)। এটা খুব ছোট, কারণ Si-এ প্রতি cm³-এ প্রায় 5 × 10²² টা atom থাকে।
  • Extrinsic = doped semiconductor। খুব অল্প পরিমাণ impurity atom মেশানো হয়। একে বলে doping। প্রতি এক million Si atom-এ মাত্র 1টা impurity atom দিলেও conductivity অনেক বেড়ে যায়।

n-type and p-typen-type আর p-type

n-type: add a pentavalent atom (5 valence electrons), like phosphorus (P), arsenic (As) or antimony (Sb). Four electrons make bonds. The fifth electron is extra and becomes free very easily. The impurity gives an electron, so it is called a donor. After giving its electron, the donor atom becomes a fixed positive ion.

p-type: add a trivalent atom (3 valence electrons), like boron (B), gallium (Ga), aluminium (Al) or indium (In). Only three bonds are made, so one bond has a missing electron — a hole. The impurity accepts an electron, so it is called an acceptor. After accepting an electron, it becomes a fixed negative ion.

Memory trick: "N = Negative carriers = eNtra electron = pENtavalent", and "P = Positive carriers = holes = trivalent (Boron)".

n-type: একটা pentavalent atom (5টা valence electron) মেশাই, যেমন phosphorus (P), arsenic (As) বা antimony (Sb)। চারটা electron bond বানায়। পঞ্চম electron-টা বাড়তি, আর খুব সহজে free হয়ে যায়। Impurity একটা electron দান করে, তাই একে বলে donor। Electron দেওয়ার পর donor atom একটা স্থির positive ion হয়ে যায়।

p-type: একটা trivalent atom (3টা valence electron) মেশাই, যেমন boron (B), gallium (Ga), aluminium (Al) বা indium (In)। মাত্র তিনটা bond হয়, তাই একটা bond-এ একটা electron কম থাকে — এটাই hole। Impurity একটা electron গ্রহণ করে, তাই একে বলে acceptor। Electron নেওয়ার পর এটা একটা স্থির negative ion হয়ে যায়।

মনে রাখার কৌশল: "N = Negative carrier = বাড়তি electron = pENtavalent", আর "P = Positive carrier = hole = trivalent (Boron)"।

n-typep-type
ImpurityImpurityPentavalent (P, As, Sb)Pentavalent (P, As, Sb)Trivalent (B, Ga, Al, In)Trivalent (B, Ga, Al, In)
Impurity nameImpurity-র নামDonorAcceptor
Majority carrierMajority carrierElectronsElectronHolesHole
Minority carrierMinority carrierHolesHoleElectronsElectron
Fixed ion left behindযে স্থির ion থাকেPositive donor ionPositive donor ionNegative acceptor ionNegative acceptor ion
Net charge of the whole crystalপুরো crystal-এর মোট chargeNeutralNeutralNeutralNeutral
MCQ trap: An n-type crystal is electrically neutral, not negative! It has extra free electrons, but it also has the same number of positive donor ions. The "n" only tells us the majority carrier is the electron. Also: majority carriers in n-type are electrons; in p-type they are holes.
MCQ trap: n-type crystal electrically neutral, negative না! এতে বাড়তি free electron আছে, কিন্তু সমান সংখ্যক positive donor ion-ও আছে। "n" শুধু বলে যে majority carrier হলো electron। আরও মনে রাখো: n-type-এ majority carrier electron; p-type-এ hole।

Mass-Action LawMass-Action Law

In any semiconductor at thermal balance (equilibrium), the product of electron and hole numbers is fixed at a given temperature:

Thermal equilibrium-এ যেকোনো semiconductor-এ, একটা নির্দিষ্ট temperature-এ electron আর hole সংখ্যার গুণফল স্থির থাকে:

\[ n \cdot p = n_i^2 \]

If we add donors ND (and ND ≫ ni), then n ≈ ND. So the holes must go down: p = ni² / ND. Adding more electrons makes more electrons meet holes and recombine, so holes become fewer.

For p-type with acceptors NA: p ≈ NA and n = ni² / NA.

Donor ND মেশালে (আর ND ≫ ni হলে), n ≈ ND। তাই hole অবশ্যই কমে যাবে: p = ni² / ND। বেশি electron মানে বেশি electron-hole মিলে recombine করে, তাই hole কমে যায়।

Acceptor NA দিয়ে p-type হলে: p ≈ NA আর n = ni² / NA।

Example: Silicon has ni = 1.5 × 10¹⁰ cm⁻³. It is doped with ND = 10¹⁶ donors/cm³. Find n and p.

Step 1: ND ≫ ni, so n ≈ ND = 10¹⁶ cm⁻³.

Step 2: ni² = (1.5 × 10¹⁰)² = 2.25 × 10²⁰.

Step 3: p = ni² / n = 2.25 × 10²⁰ / 10¹⁶ = 2.25 × 10⁴ cm⁻³.

Look at the gap: electrons are about 10¹² times more than holes. Electrons are clearly the majority carriers.

Example: Silicon-এর ni = 1.5 × 10¹⁰ cm⁻³। একে ND = 10¹⁶ donors/cm³ দিয়ে dope করা হলো। n আর p বের করো।

Step 1: ND ≫ ni, তাই n ≈ ND = 10¹⁶ cm⁻³।

Step 2: ni² = (1.5 × 10¹⁰)² = 2.25 × 10²⁰।

Step 3: p = ni² / n = 2.25 × 10²⁰ / 10¹⁶ = 2.25 × 10⁴ cm⁻³।

পার্থক্যটা দেখো: electron, hole-এর চেয়ে প্রায় 10¹² গুণ বেশি। স্পষ্টতই electron হলো majority carrier।

Example: Si (ni = 1.5 × 10¹⁰ cm⁻³) is doped with boron, NA = 10¹⁵ cm⁻³. Which type is it? Find the minority carrier concentration.

Boron is trivalent → acceptor → p-type. Majority: holes, p ≈ 10¹⁵ cm⁻³.

Minority (electrons): n = (1.5 × 10¹⁰)² / 10¹⁵ = 2.25 × 10²⁰ / 10¹⁵ = 2.25 × 10⁵ cm⁻³.

Example: Si (ni = 1.5 × 10¹⁰ cm⁻³)-কে boron দিয়ে dope করা হলো, NA = 10¹⁵ cm⁻³। এটা কোন type? Minority carrier concentration বের করো।

Boron trivalent → acceptor → p-type। Majority: hole, p ≈ 10¹⁵ cm⁻³।

Minority (electron): n = (1.5 × 10¹⁰)² / 10¹⁵ = 2.25 × 10²⁰ / 10¹⁵ = 2.25 × 10⁵ cm⁻³।

Drift Current and Diffusion CurrentDrift Current আর Diffusion Current

Carriers can move in two ways:

  • Drift current — caused by an electric field (a voltage). Holes move along the field, electrons move against it. Both give current in the same direction. Formula idea: J = q(nμn + pμp)E, where μ is mobility (how easily a carrier moves). In Si, electron mobility (≈ 1350 cm²/V·s) is about 3 times hole mobility (≈ 480 cm²/V·s). So electrons are faster. That is why n-type devices (npn, nMOS) are faster.
  • Diffusion current — caused by a difference in concentration. Carriers spread from where there are many to where there are few, like perfume spreading in a room. No field is needed.

Carrier দুইভাবে চলতে পারে:

  • Drift current — electric field (voltage)-এর কারণে হয়। Hole field-এর দিকে চলে, electron উল্টো দিকে চলে। দুটোই একই দিকে current দেয়। Formula-র ধারণা: J = q(nμn + pμp)E, এখানে μ হলো mobility (carrier কত সহজে চলে)। Si-এ electron mobility (≈ 1350 cm²/V·s) hole mobility (≈ 480 cm²/V·s)-এর প্রায় 3 গুণ। তাই electron দ্রুত। এজন্যই n-type device (npn, nMOS) বেশি fast।
  • Diffusion current — concentration-এর পার্থক্য-এর কারণে হয়। যেখানে carrier বেশি, সেখান থেকে যেখানে কম সেখানে ছড়িয়ে পড়ে, যেমন ঘরে perfume ছড়িয়ে পড়ে। কোনো field লাগে না।

Effect of TemperatureTemperature-এর প্রভাব

  • More heat → more electrons jump the gap → ni goes up very fast (it grows exponentially).
  • So a semiconductor's resistance goes down when it gets hotter. We say it has a negative temperature coefficient of resistance. A metal is the opposite: its resistance goes up with heat.
  • At 0 K (absolute zero), a pure semiconductor has no free carriers. It acts like an insulator.
  • Too much heat is bad for doped devices: when ni becomes close to the doping level, the n-type or p-type behaviour is lost. Ge has a smaller gap, so it fails at lower temperature (≈ 75 °C) than Si (≈ 150 °C). This is one big reason Si replaced Ge.
  • বেশি তাপ → বেশি electron gap পার হয় → ni খুব দ্রুত বাড়ে (exponentially বাড়ে)।
  • তাই গরম হলে semiconductor-এর resistance কমে। বলা হয় এর resistance-এর negative temperature coefficient। Metal উল্টো: তাপে এর resistance বাড়ে।
  • 0 K (absolute zero)-এ pure semiconductor-এ কোনো free carrier থাকে না। তখন এটা insulator-এর মতো আচরণ করে।
  • অতিরিক্ত তাপ doped device-এর জন্য খারাপ: ni যখন doping level-এর কাছাকাছি চলে যায়, n-type বা p-type আচরণ নষ্ট হয়ে যায়। Ge-এর gap ছোট, তাই এটা Si (≈ 150 °C)-এর চেয়ে কম temperature-এ (≈ 75 °C) নষ্ট হয়। Si দিয়ে Ge-কে replace করার এটা একটা বড় কারণ।
Exam tips: (1) Semiconductor at 0 K = insulator. (2) Semiconductor resistance falls with temperature (negative temperature coefficient). (3) Bigger band gap → fewer carriers at room temperature → less leakage. (4) For MCQ, remember the three numbers: Ge 0.67 eV, Si 1.1 eV, GaAs 1.43 eV.
Exam tips: (1) 0 K-এ semiconductor = insulator। (2) Temperature বাড়লে semiconductor-এর resistance কমে (negative temperature coefficient)। (3) বড় band gap → room temperature-এ কম carrier → কম leakage। (4) MCQ-এর জন্য তিনটা সংখ্যা মনে রাখো: Ge 0.67 eV, Si 1.1 eV, GaAs 1.43 eV।

2. PN Junction Diode2. PN Junction Diode

A diode is made by joining a p-type piece and an n-type piece in one crystal. The joining surface is called the PN junction. A diode is like a one-way valve for current: current flows easily from p to n, but almost not at all from n to p.

The p side is called the anode (A). The n side is called the cathode (K). In the symbol, the triangle points in the direction of easy current flow (anode → cathode), and the bar is the cathode.

একটা crystal-এ p-type আর n-type অংশ জোড়া লাগিয়ে diode বানানো হয়। জোড়ার জায়গাটাকে বলে PN junction। Diode হলো current-এর জন্য একমুখী valve-এর মতো: p থেকে n-এর দিকে current সহজে চলে, কিন্তু n থেকে p-এর দিকে প্রায় চলেই না।

p side-কে বলে anode (A)। n side-কে বলে cathode (K)। Symbol-এ triangle-টা সহজ current-এর দিকে নির্দেশ করে (anode → cathode), আর bar-টা হলো cathode।

How the Depletion Region FormsDepletion Region কীভাবে তৈরি হয়

  1. The n side has many free electrons. The p side has many holes.
  2. Because of the concentration difference, electrons diffuse from n to p, and holes diffuse from p to n.
  3. Near the junction, these electrons and holes meet and recombine (cancel each other).
  4. What is left near the junction? Only the fixed ions: positive donor ions on the n side and negative acceptor ions on the p side. This thin zone has no free carriers. It is called the depletion region (or space-charge region).
  5. These ions make an electric field pointing from n to p. This field pushes back any more carriers that try to cross. After some time, diffusion and this push-back balance. The voltage across this region is the barrier potential (built-in potential).

Barrier potential at room temperature: Si ≈ 0.7 V, Ge ≈ 0.3 V. So to make a Si diode conduct well, we must apply about 0.7 V in the forward direction. This is also called the cut-in or knee voltage.

  1. n side-এ অনেক free electron আছে। p side-এ অনেক hole আছে।
  2. Concentration-এর পার্থক্যের কারণে electron n থেকে p-তে diffuse করে, আর hole p থেকে n-এ diffuse করে।
  3. Junction-এর কাছে এই electron আর hole মিলে recombine করে (একে অপরকে cancel করে)।
  4. Junction-এর কাছে কী থাকে? শুধু স্থির ion: n side-এ positive donor ion আর p side-এ negative acceptor ion। এই পাতলা অংশে কোনো free carrier থাকে না। একে বলে depletion region (বা space-charge region)।
  5. এই ion গুলো n থেকে p-এর দিকে একটা electric field তৈরি করে। আর কোনো carrier পার হতে চাইলে এই field তাকে ঠেলে ফেরত পাঠায়। কিছুক্ষণ পর diffusion আর এই ঠেলা balance হয়ে যায়। এই region-এর voltage-কে বলে barrier potential (built-in potential)।

Room temperature-এ barrier potential: Si ≈ 0.7 V, Ge ≈ 0.3 V। তাই Si diode ঠিকমতো conduct করাতে forward দিকে প্রায় 0.7 V দিতে হয়। একে cut-in বা knee voltage-ও বলে।

PN junction at equilibrium: carrier density, charge density, electric field and potential
A PN junction at equilibrium: carrier density, space charge, electric field and built-in potential across the depletion region. (Wikimedia Commons)Equilibrium-এ একটা PN junction: depletion region জুড়ে carrier density, space charge, electric field আর built-in potential। (Wikimedia Commons)

Forward Bias and Reverse BiasForward Bias আর Reverse Bias

Forward biasReverse bias
ConnectionConnection+ to p (anode), − to n (cathode)+ যায় p (anode)-তে, − যায় n (cathode)-এ+ to n, − to p+ যায় n-এ, − যায় p-তে
Depletion regionDepletion regionBecomes narrowসরু হয়Becomes wideচওড়া হয়
BarrierBarrierLoweredকমেRaisedবাড়ে
CurrentCurrentLarge (mA to A), by majority carriersবড় (mA থেকে A), majority carrier দিয়েTiny (nA for Si, µA for Ge), by minority carriersখুব ছোট (Si-এ nA, Ge-এ µA), minority carrier দিয়ে
ResistanceResistanceLowকমVery highঅনেক বেশি
MCQ trap: The small reverse current (reverse saturation current Is) is caused by minority carriers, not majority carriers. The minority carriers are made by heat, so Is depends strongly on temperature. A common rule: Is doubles for every 10 °C rise. It hardly depends on the reverse voltage (that is why it is called "saturation" current).
MCQ trap: ছোট reverse current (reverse saturation current Is) তৈরি হয় minority carrier দিয়ে, majority carrier দিয়ে না। Minority carrier তাপ থেকে তৈরি হয়, তাই Is temperature-এর উপর অনেক নির্ভর করে। একটা common rule: প্রতি 10 °C বাড়লে Is দ্বিগুণ হয়। Reverse voltage-এর উপর এটা প্রায় নির্ভর করে না (এজন্যই একে "saturation" current বলে)।

I–V CharacteristicI–V Characteristic

VD ID Ge Si 0.7 0.3 Forward region (knee / cut-in) Reverse region: I ≈ −Is (nA) −VBR (breakdown) Breakdown: current rises sharply Note: forward and reverse axes use different scales
Diode I–V curve. Almost no current until about 0.7 V (Si) or 0.3 V (Ge), then current rises very fast. In reverse, only a tiny leakage flows until breakdown.Diode-এর I–V curve। প্রায় 0.7 V (Si) বা 0.3 V (Ge) পর্যন্ত প্রায় কোনো current নেই, তারপর current খুব দ্রুত বাড়ে। Reverse-এ breakdown পর্যন্ত শুধু খুব ছোট leakage চলে।

Shockley Diode EquationShockley Diode Equation

\[ I_D = I_s \left( e^{V_D / (n V_T)} - 1 \right), \qquad V_T = \frac{kT}{q} \approx 26\ \text{mV at } 300\ \text{K} \]
  • Is = reverse saturation current (very small, like 10⁻¹⁴ A for a small Si diode).
  • VT = thermal voltage. k = 1.38 × 10⁻²³ J/K (Boltzmann), q = 1.6 × 10⁻¹⁹ C. At T = 300 K: VT = (1.38 × 10⁻²³ × 300)/(1.6 × 10⁻¹⁹) ≈ 0.0259 V ≈ 26 mV.
  • n = ideality factor, between 1 and 2 (take n = 1 if not given).
  • In forward bias with VD ≫ VT, the "−1" can be ignored: ID ≈ Is eVD/nVT.
  • In reverse bias (VD very negative), the exponential → 0, so ID ≈ −Is.
  • Is = reverse saturation current (খুব ছোট, ছোট Si diode-এ যেমন 10⁻¹⁴ A)।
  • VT = thermal voltage। k = 1.38 × 10⁻²³ J/K (Boltzmann), q = 1.6 × 10⁻¹⁹ C। T = 300 K-এ: VT = (1.38 × 10⁻²³ × 300)/(1.6 × 10⁻¹⁹) ≈ 0.0259 V ≈ 26 mV।
  • n = ideality factor, 1 থেকে 2-এর মধ্যে (দেওয়া না থাকলে n = 1 ধরো)।
  • Forward bias-এ VD ≫ VT হলে "−1" বাদ দেওয়া যায়: ID ≈ Is eVD/nVT।
  • Reverse bias-এ (VD অনেক negative), exponential → 0, তাই ID ≈ −Is।
Example: A Si diode has Is = 10⁻¹⁴ A, n = 1, VT = 26 mV. Find ID at VD = 0.7 V and at 0.6 V.

At 0.7 V: VD/VT = 0.7/0.026 = 26.92. e26.92 ≈ 4.93 × 10¹¹. So ID ≈ 10⁻¹⁴ × 4.93 × 10¹¹ = 4.93 × 10⁻³ A ≈ 4.9 mA.

At 0.6 V: 0.6/0.026 = 23.08. e23.08 ≈ 1.05 × 10¹⁰. So ID ≈ 0.105 mA.

Only 0.1 V more gave about 47 times more current! This is why we treat a Si diode as "0.7 V when ON".

Example: একটা Si diode-এর Is = 10⁻¹⁴ A, n = 1, VT = 26 mV। VD = 0.7 V আর 0.6 V-এ ID বের করো।

0.7 V-এ: VD/VT = 0.7/0.026 = 26.92। e26.92 ≈ 4.93 × 10¹¹। তাই ID ≈ 10⁻¹⁴ × 4.93 × 10¹¹ = 4.93 × 10⁻³ A ≈ 4.9 mA।

0.6 V-এ: 0.6/0.026 = 23.08। e23.08 ≈ 1.05 × 10¹⁰। তাই ID ≈ 0.105 mA।

মাত্র 0.1 V বেশিতে প্রায় 47 গুণ বেশি current! এজন্যই আমরা Si diode-কে "ON হলে 0.7 V" ধরে নিই।

Example (the 60 mV rule): How much must VD rise to make the current 10 times bigger? (n = 1)

I2/I1 = eΔV/VT = 10 → ΔV = VT ln 10 = 0.026 × 2.303 ≈ 60 mV. So every 60 mV extra gives 10× current. (For n = 2, it is 120 mV.)

Example (60 mV rule): Current 10 গুণ করতে VD কতটুকু বাড়াতে হবে? (n = 1)

I2/I1 = eΔV/VT = 10 → ΔV = VT ln 10 = 0.026 × 2.303 ≈ 60 mV। মানে প্রতি 60 mV বাড়ালে current 10 গুণ হয়। (n = 2 হলে 120 mV।)

Example (temperature): A Si diode has Is = 10 nA at 25 °C. Find Is at 55 °C.

Rise = 30 °C = 3 steps of 10 °C. Is doubles each step: 10 × 2³ = 80 nA.

Also, the forward drop falls by about 2 mV per °C. So a 0.7 V drop at 25 °C becomes about 0.7 − 0.002 × 30 = 0.64 V at 55 °C.

Example (temperature): একটা Si diode-এর 25 °C-এ Is = 10 nA। 55 °C-এ Is কত?

বৃদ্ধি = 30 °C = 10 °C-এর 3টা step। প্রতি step-এ Is দ্বিগুণ: 10 × 2³ = 80 nA।

আরও, forward drop প্রতি °C-এ প্রায় 2 mV করে কমে। তাই 25 °C-এ 0.7 V drop 55 °C-এ হয় প্রায় 0.7 − 0.002 × 30 = 0.64 V।

Breakdown: Avalanche vs ZenerBreakdown: Avalanche বনাম Zener

If the reverse voltage becomes too large, the current suddenly shoots up. This is breakdown. It is not always damage — if the current is limited by a resistor, the diode is safe. There are two ways it happens:

Reverse voltage খুব বেশি হলে current হঠাৎ অনেক বেড়ে যায়। একে বলে breakdown। এটা সবসময় ক্ষতি না — resistor দিয়ে current limit করলে diode নিরাপদ থাকে। এটা দুইভাবে হয়:

Zener breakdownAvalanche breakdown
DopingDopingHeavy doping, very thin depletion regionHeavy doping, খুব পাতলা depletion regionLight doping, wide depletion regionLight doping, চওড়া depletion region
How it happensকীভাবে হয়Very strong field pulls electrons straight out of their bonds (tunneling)খুব শক্তিশালী field সরাসরি bond থেকে electron টেনে বের করে (tunneling)Fast carriers hit atoms and knock out more carriers — a chain reaction (impact ionization)দ্রুতগামী carrier atom-কে ধাক্কা দিয়ে আরও carrier বের করে — chain reaction (impact ionization)
VoltageVoltageLow, below about 5 Vকম, প্রায় 5 V-এর নিচেHigher, above about 6 Vবেশি, প্রায় 6 V-এর উপরে
Temperature coefficientTemperature coefficientNegative (VZ falls when hot)Negative (গরমে VZ কমে)Positive (VBR rises when hot)Positive (গরমে VBR বাড়ে)
Fun fact for MCQ: A Zener diode of about 5–6 V has both effects together. They cancel, so its voltage barely changes with temperature. That is why ~5.6 V Zeners are popular as stable references.
MCQ-এর জন্য মজার তথ্য: প্রায় 5–6 V-এর Zener diode-এ দুইটা effect একসাথে থাকে। এরা একে অপরকে cancel করে, তাই temperature-এ এর voltage প্রায় বদলায় না। এজন্যই ~5.6 V Zener stable reference হিসেবে জনপ্রিয়।

Diode Models (for solving circuits)Diode Model (circuit solve করার জন্য)

ModelWhen ON (forward)ON হলে (forward)When OFF (reverse)OFF হলে (reverse)Useব্যবহার
1. IdealShort circuit, 0 V dropShort circuit, 0 V dropOpen circuitOpen circuitBig voltages, quick ideaবড় voltage, দ্রুত ধারণা
2. Constant-dropFixed 0.7 V (Si) / 0.3 V (Ge) batteryFixed 0.7 V (Si) / 0.3 V (Ge) batteryOpen circuitOpen circuitMost exam problemsবেশিরভাগ exam problem
3. Piecewise-linear0.7 V battery + small resistor rd in series0.7 V battery + series-এ ছোট resistor rdOpen circuitOpen circuitMore accurateবেশি accurate

Small-signal (dynamic) resistance of a diode: rd = VT / ID. At ID = 1 mA, rd = 26 mV / 1 mA = 26 Ω.

Diode-এর small-signal (dynamic) resistance: rd = VT / ID। ID = 1 mA হলে rd = 26 mV / 1 mA = 26 Ω।

Example (one circuit, three models): A 10 V battery, a 1 kΩ resistor and a Si diode are in series. The diode is forward biased. Find the current with each model. For piecewise-linear, take rd = 20 Ω.

Ideal: I = 10 / 1000 = 10 mA.

Constant-drop: KVL: 10 = 0.7 + I × 1000 → I = 9.3 / 1000 = 9.3 mA.

Piecewise-linear: 10 = 0.7 + I(1000 + 20) → I = 9.3 / 1020 = 9.12 mA.

The answers are close. When the source is much bigger than 0.7 V, even the ideal model is fine.

If the diode is turned around (reverse biased), it is OFF: I ≈ 0, and the whole 10 V appears across the diode.

Example (একই circuit, তিনটা model): একটা 10 V battery, একটা 1 kΩ resistor আর একটা Si diode series-এ আছে। Diode forward biased। প্রতিটা model দিয়ে current বের করো। Piecewise-linear-এর জন্য rd = 20 Ω ধরো।

Ideal: I = 10 / 1000 = 10 mA।

Constant-drop: KVL: 10 = 0.7 + I × 1000 → I = 9.3 / 1000 = 9.3 mA।

Piecewise-linear: 10 = 0.7 + I(1000 + 20) → I = 9.3 / 1020 = 9.12 mA।

উত্তরগুলো কাছাকাছি। Source যদি 0.7 V-এর চেয়ে অনেক বড় হয়, তাহলে ideal model-ও ঠিক আছে।

Diode উল্টো করে দিলে (reverse biased) এটা OFF: I ≈ 0, আর পুরো 10 V diode-এর উপর পড়ে।

Example (assume, then check): A 5 V source feeds R1 = 1 kΩ in series. After R1, a Si diode (anode up) and R2 = 1 kΩ are connected in parallel to ground. Find all currents.

Step 1 — Is the diode ON? Remove it first. Then the voltage across R2 = 5 × 1/(1+1) = 2.5 V. This is more than 0.7 V, so the diode will turn ON.

Step 2 — With the diode ON, the node is held at 0.7 V.

IR1 = (5 − 0.7)/1 kΩ = 4.3 mA. IR2 = 0.7/1 kΩ = 0.7 mA. ID = 4.3 − 0.7 = 3.6 mA.

Step 3 — Check: ID is positive (forward), so the assumption was right.

Example (ধরে নাও, তারপর check করো): একটা 5 V source-এর সাথে series-এ R1 = 1 kΩ। R1-এর পরে একটা Si diode (anode উপরে) আর R2 = 1 kΩ parallel-এ ground-এ যুক্ত। সব current বের করো।

Step 1 — Diode কি ON? আগে এটা সরিয়ে দাও। তখন R2-এর voltage = 5 × 1/(1+1) = 2.5 V। এটা 0.7 V-এর বেশি, তাই diode ON হবে।

Step 2 — Diode ON হলে node-টা 0.7 V-এ আটকে থাকে।

IR1 = (5 − 0.7)/1 kΩ = 4.3 mA। IR2 = 0.7/1 kΩ = 0.7 mA। ID = 4.3 − 0.7 = 3.6 mA।

Step 3 — Check: ID positive (forward), তাই ধারণা ঠিক ছিল।

Exam method for any diode circuit: (1) Guess the state (ON or OFF). (2) Replace the diode by its model (0.7 V source or open). (3) Solve with KVL/KCL. (4) Check: ON diode must have forward current; OFF diode must have VD < 0.7 V. If the check fails, change the guess.
যেকোনো diode circuit-এর exam method: (1) State অনুমান করো (ON না OFF)। (2) Diode-কে তার model দিয়ে replace করো (0.7 V source বা open)। (3) KVL/KCL দিয়ে solve করো। (4) Check: ON diode-এ forward current থাকতে হবে; OFF diode-এ VD < 0.7 V হতে হবে। Check fail করলে অনুমান বদলাও।

3. Diode Applications: Rectifier, Filter, Clipper, Clamper3. Diode Applications: Rectifier, Filter, Clipper, Clamper

The wall socket gives AC (in Bangladesh, 220 V rms, 50 Hz). Your laptop and phone need DC. A power supply changes AC to DC in these steps:

Transformer (steps voltage down) → Rectifier (diodes make it one-way) → Filter (capacitor smooths it) → Regulator (Zener or IC keeps it fixed) → DC output.

Useful AC facts: peak voltage Vm = √2 × Vrms. So 220 V rms has a peak of 220 × 1.414 = 311 V.

দেয়ালের socket থেকে AC আসে (বাংলাদেশে 220 V rms, 50 Hz)। তোমার laptop আর phone-এর দরকার DC। একটা power supply এই ধাপে AC-কে DC বানায়:

Transformer (voltage কমায়) → Rectifier (diode দিয়ে একমুখী করে) → Filter (capacitor দিয়ে মসৃণ করে) → Regulator (Zener বা IC দিয়ে fixed রাখে) → DC output।

দরকারি AC তথ্য: peak voltage Vm = √2 × Vrms। তাই 220 V rms-এর peak = 220 × 1.414 = 311 V।

Half-Wave RectifierHalf-Wave Rectifier

Just one diode in series with the load. In the positive half cycle the diode is ON, so the load gets the input. In the negative half cycle the diode is OFF, so the load gets 0 V. Half of the wave is thrown away.

Load-এর সাথে series-এ মাত্র একটা diode। Positive half cycle-এ diode ON, তাই load input পায়। Negative half cycle-এ diode OFF, তাই load 0 V পায়। Wave-এর অর্ধেক নষ্ট হয়।

\[ V_{dc} = \frac{V_m}{\pi} \approx 0.318\,V_m, \qquad V_{rms} = \frac{V_m}{2}, \qquad \text{PIV} = V_m \]

Full-Wave Rectifier: Center-Tap and BridgeFull-Wave Rectifier: Center-Tap আর Bridge

A full-wave rectifier uses both halves. The negative half is flipped up. So we get two humps per input cycle.

  • Center-tap (CT): uses a transformer with a middle tap and 2 diodes. Each diode works for one half. When one diode is ON, the OFF diode must block the voltage of the whole secondary, so its PIV = 2Vm (Vm = peak of each half).
  • Bridge: uses 4 diodes and no center tap. In each half, 2 diodes are ON in series. Each OFF diode blocks only Vm, so PIV = Vm. The cost: two diode drops (2 × 0.7 = 1.4 V for Si) instead of one.

Full-wave rectifier দুইটা half-ই ব্যবহার করে। Negative half-কে উল্টে উপরে তোলা হয়। তাই প্রতি input cycle-এ দুইটা কুঁজ (hump) পাই।

  • Center-tap (CT): মাঝখানে tap-ওয়ালা transformer আর 2টা diode লাগে। প্রতিটা diode এক half-এ কাজ করে। একটা diode ON থাকলে, OFF diode-কে পুরো secondary-র voltage আটকাতে হয়, তাই এর PIV = 2Vm (Vm = প্রতি অর্ধেকের peak)।
  • Bridge: 4টা diode লাগে, center tap লাগে না। প্রতি half-এ 2টা diode series-এ ON থাকে। প্রতিটা OFF diode শুধু Vm আটকায়, তাই PIV = Vm। দাম: একটার বদলে দুইটা diode drop (Si-এ 2 × 0.7 = 1.4 V)।
\[ V_{dc} = \frac{2V_m}{\pi} \approx 0.636\,V_m, \qquad V_{rms} = \frac{V_m}{\sqrt{2}}, \qquad \text{PIV}_{CT} = 2V_m, \quad \text{PIV}_{bridge} = V_m \]
RL + − D1D2 D3D4 AC + half: D2, D3 ON · − half: D4, D1 ON
Bridge rectifier. In each half cycle two diodes conduct in series, and the current always goes through RL in the same direction.Bridge rectifier। প্রতি half cycle-এ দুইটা diode series-এ conduct করে, আর RL-এর মধ্যে current সবসময় একই দিকে যায়।
Input AC t Half-wave output t Full-wave output t +Vm −Vm 1 hump per cycle 2 humps per cycle red dashed = with capacitor filter (ripple Vr)
Top: AC input. Middle: half-wave output (one hump per cycle). Bottom: full-wave output (two humps per cycle); the red dashed line shows the output after a capacitor filter.উপরে: AC input। মাঝে: half-wave output (প্রতি cycle-এ একটা hump)। নিচে: full-wave output (প্রতি cycle-এ দুইটা hump); লাল dashed line হলো capacitor filter-এর পরের output।
PropertyPropertyHalf-waveFull-wave CTBridge
Number of diodesDiode সংখ্যা124
VdcVm/π = 0.318 Vm2Vm/π = 0.636 Vm2Vm/π = 0.636 Vm
VrmsVm/2Vm/√2Vm/√2
PIVVm2VmVm
Ripple frequencyRipple frequencyf (50 Hz)2f (100 Hz)2f (100 Hz)
Ripple factor (no filter)Ripple factor (filter ছাড়া)1.210.4820.482
Max efficiencyMax efficiency40.6%81.2%81.2%
Diode drops in path (Si)Path-এ diode drop (Si)0.7 V0.7 V1.4 V
Needs center-tap transformer?Center-tap transformer লাগে?NoনাYesহ্যাঁNoনা
MCQ trap (very common): PIV of a bridge rectifier = Vm, but PIV of a center-tap rectifier = 2Vm. Also, the ripple frequency of any full-wave rectifier on 50 Hz mains is 100 Hz, not 50 Hz.
MCQ trap (খুব common): Bridge rectifier-এর PIV = Vm, কিন্তু center-tap rectifier-এর PIV = 2Vm। আরও, 50 Hz mains-এ যেকোনো full-wave rectifier-এর ripple frequency 100 Hz, 50 Hz না।
Example: The peak input is Vm = 20 V. Use ideal diodes. Find Vdc and Vrms for half-wave and full-wave rectifiers.

Half-wave: Vdc = 20/π = 6.37 V. Vrms = 20/2 = 10 V.

Full-wave: Vdc = 2 × 20/π = 12.73 V. Vrms = 20/√2 = 14.14 V.

Full-wave gives exactly double the DC value of half-wave.

Example: Peak input Vm = 20 V। Ideal diode ধরো। Half-wave আর full-wave rectifier-এর Vdc আর Vrms বের করো।

Half-wave: Vdc = 20/π = 6.37 V। Vrms = 20/2 = 10 V।

Full-wave: Vdc = 2 × 20/π = 12.73 V। Vrms = 20/√2 = 14.14 V।

Full-wave-এ DC value ঠিক half-wave-এর দ্বিগুণ।

Example (with transformer and real Si diodes): 220 V rms, 50 Hz mains goes into a 10:1 step-down transformer. Compare a bridge rectifier and a center-tap rectifier (for CT, assume each half of the secondary gives 22 V rms).

Secondary: 220/10 = 22 V rms → Vm = 22 × √2 = 31.11 V.

Bridge: two drops → output peak = 31.11 − 1.4 = 29.71 V. Vdc = 2 × 29.71/π = 18.92 V. PIV ≈ Vm − 0.7 = 30.4 V (≈ Vm = 31.1 V if ideal).

Center-tap: one drop → output peak = 31.11 − 0.7 = 30.41 V. Vdc = 2 × 30.41/π = 19.36 V. PIV = 2Vm − 0.7 = 61.5 V (≈ 2Vm = 62.2 V if ideal).

Ripple frequency in both: 2 × 50 = 100 Hz. So the CT gives slightly more DC, but its diodes must handle double the reverse voltage.

Example (transformer আর আসল Si diode সহ): 220 V rms, 50 Hz mains একটা 10:1 step-down transformer-এ যায়। Bridge rectifier আর center-tap rectifier তুলনা করো (CT-এর জন্য ধরো secondary-র প্রতি অর্ধেক 22 V rms দেয়)।

Secondary: 220/10 = 22 V rms → Vm = 22 × √2 = 31.11 V।

Bridge: দুইটা drop → output peak = 31.11 − 1.4 = 29.71 V। Vdc = 2 × 29.71/π = 18.92 V। PIV ≈ Vm − 0.7 = 30.4 V (ideal হলে ≈ Vm = 31.1 V)।

Center-tap: একটা drop → output peak = 31.11 − 0.7 = 30.41 V। Vdc = 2 × 30.41/π = 19.36 V। PIV = 2Vm − 0.7 = 61.5 V (ideal হলে ≈ 2Vm = 62.2 V)।

দুইটাতেই ripple frequency: 2 × 50 = 100 Hz। তাই CT একটু বেশি DC দেয়, কিন্তু এর diode-কে দ্বিগুণ reverse voltage সহ্য করতে হয়।

Capacitor Filter and RippleCapacitor Filter আর Ripple

The rectifier output is bumpy DC. We put a big capacitor C across the load R. Near each peak, the capacitor charges to Vm. Between peaks, the diodes are OFF, and the capacitor slowly discharges into R. The small up-down change left over is called ripple (Vr, peak-to-peak).

Rectifier-এর output উঁচুনিচু DC। Load R-এর across-এ একটা বড় capacitor C লাগাই। প্রতিটা peak-এর কাছে capacitor Vm পর্যন্ত charge হয়। দুই peak-এর মাঝে diode OFF থাকে, আর capacitor ধীরে ধীরে R-এ discharge হয়। যে ছোট ওঠানামা থেকে যায়, তাকে বলে ripple (Vr, peak-to-peak)।

\[ V_r \approx \frac{V_m}{f\,R\,C} = \frac{I_{dc}}{f\,C}, \qquad V_{dc} \approx V_m - \frac{V_r}{2} \]

Here f is the ripple frequency: f = 50 Hz for half-wave, f = 100 Hz for full-wave (on 50 Hz mains). Bigger C, bigger R or higher f → smaller ripple.

এখানে f হলো ripple frequency: half-wave-এ f = 50 Hz, full-wave-এ f = 100 Hz (50 Hz mains-এ)। C বড়, R বড় বা f বেশি হলে → ripple কমে।

Example: A full-wave rectifier on 50 Hz mains gives Vm = 20 V. Load R = 1 kΩ. Filter C = 470 µF. Find the ripple and the DC output. What if it were half-wave?

Full-wave → f = 100 Hz.

Vr = 20 / (100 × 1000 × 470 × 10⁻⁶) = 20 / 47 = 0.43 V (peak-to-peak).

Vdc ≈ 20 − 0.43/2 = 19.79 V. Compare with 12.73 V without the capacitor — a big jump!

Ripple factor ≈ Vr(rms)/Vdc = (0.43/(2√3))/19.79 = 0.123/19.79 ≈ 0.62%.

Half-wave → f = 50 Hz → Vr = 20/(50 × 1000 × 470 × 10⁻⁶) = 0.85 V. Double the ripple.

Example: 50 Hz mains-এ একটা full-wave rectifier Vm = 20 V দেয়। Load R = 1 kΩ। Filter C = 470 µF। Ripple আর DC output বের করো। Half-wave হলে কী হতো?

Full-wave → f = 100 Hz।

Vr = 20 / (100 × 1000 × 470 × 10⁻⁶) = 20 / 47 = 0.43 V (peak-to-peak)।

Vdc ≈ 20 − 0.43/2 = 19.79 V। Capacitor ছাড়া ছিল 12.73 V — অনেক বড় লাফ!

Ripple factor ≈ Vr(rms)/Vdc = (0.43/(2√3))/19.79 = 0.123/19.79 ≈ 0.62%।

Half-wave → f = 50 Hz → Vr = 20/(50 × 1000 × 470 × 10⁻⁶) = 0.85 V। Ripple দ্বিগুণ।

Clipper (Limiter) CircuitsClipper (Limiter) Circuit

A clipper cuts off the part of a signal above (or below) some level. The rest passes unchanged. It is used to protect inputs from high voltage (for example, the protection diodes on every microcontroller pin).

  • Shunt positive clipper: a diode across the output, anode on the output side. When the output tries to go above 0.7 V, the diode turns ON and holds it at 0.7 V.
  • Biased clipper: add a battery VB in series with the diode. Now the clip level is VB + 0.7 V.
  • Negative clipper: turn the diode around. It clips the negative part at −0.7 V (or −(VB + 0.7)).
  • Double clipper: two diodes back-to-back → output stays between −0.7 V and +0.7 V.

Clipper একটা signal-এর কোনো নির্দিষ্ট level-এর উপরের (বা নিচের) অংশ কেটে দেয়। বাকিটা অপরিবর্তিত যায়। High voltage থেকে input রক্ষা করতে এটা ব্যবহার হয় (যেমন প্রতিটা microcontroller pin-এর protection diode)।

  • Shunt positive clipper: output-এর across-এ একটা diode, anode output-এর দিকে। Output 0.7 V-এর উপরে যেতে চাইলে diode ON হয় আর 0.7 V-এ আটকে রাখে।
  • Biased clipper: diode-এর সাথে series-এ একটা battery VB দাও। এখন clip level = VB + 0.7 V।
  • Negative clipper: diode উল্টে দাও। এটা negative অংশকে −0.7 V-এ (বা −(VB + 0.7)-এ) কাটে।
  • Double clipper: দুইটা diode উল্টোমুখী করে পাশাপাশি → output −0.7 V আর +0.7 V-এর মধ্যে থাকে।
Example: Input = 10 sin ωt V. A shunt clipper has a Si diode in series with VB = 3 V (diode ON when output > VB + 0.7). A series resistor is at the input. Sketch the output.

Clip level = 3 + 0.7 = 3.7 V. When vin < 3.7 V, the diode is OFF and vout = vin. When vin > 3.7 V, the diode is ON and vout = 3.7 V.

So the output goes from −10 V to +3.7 V. The top is flat (see the left graph below).

Example: Input = 10 sin ωt V। একটা shunt clipper-এ Si diode-এর সাথে series-এ VB = 3 V (output > VB + 0.7 হলে diode ON)। Input-এ একটা series resistor আছে। Output আঁকো।

Clip level = 3 + 0.7 = 3.7 V। vin < 3.7 V হলে diode OFF, vout = vin। vin > 3.7 V হলে diode ON, vout = 3.7 V।

তাই output −10 V থেকে +3.7 V পর্যন্ত যায়। উপরের অংশটা সমান (নিচের বাম graph দেখো)।

Clamper (DC Restorer)Clamper (DC Restorer)

A clamper does not cut the signal. It shifts the whole signal up or down by adding a DC level. The shape and the peak-to-peak value stay the same. It uses a capacitor, a diode and a resistor.

  • In the first half cycle, the diode turns ON and the capacitor charges to the peak (Vm).
  • After that, the capacitor acts like a battery of Vm in series with the input. So the output = input ± Vm.
  • Negative clamper: pushes the signal down so that its top touches 0 V. Positive clamper: pushes it up so its bottom touches 0 V.
  • To work well, the RC time constant must be much longer than the signal period (so C does not discharge between cycles).

Clamper signal কাটে না। এটা একটা DC level যোগ করে পুরো signal-কে উপরে বা নিচে সরিয়ে দেয়। আকার আর peak-to-peak value একই থাকে। এতে একটা capacitor, একটা diode আর একটা resistor লাগে।

  • প্রথম half cycle-এ diode ON হয় আর capacitor peak (Vm) পর্যন্ত charge হয়।
  • এরপর capacitor input-এর সাথে series-এ Vm-এর একটা battery-র মতো কাজ করে। তাই output = input ± Vm।
  • Negative clamper: signal-কে নিচে নামায় যাতে এর উপরের মাথা 0 V ছোঁয়। Positive clamper: উপরে তোলে যাতে নিচের মাথা 0 V ছোঁয়।
  • ঠিকমতো কাজ করতে RC time constant signal period-এর চেয়ে অনেক বড় হতে হবে (যাতে দুই cycle-এর মাঝে C discharge না হয়)।
Example: A ±10 V square wave (20 V peak-to-peak) goes into a negative clamper. Use an ideal diode. Find the output range. Repeat with a Si diode.

Ideal: the top is pushed to 0 V. The peak-to-peak stays 20 V. So the output goes from 0 V to −20 V.

Si diode: the capacitor charges to 10 − 0.7 = 9.3 V. The output = input − 9.3 → from +0.7 V to −19.3 V. Still 20 V peak-to-peak.

With a positive clamper (ideal), the output would be 0 V to +20 V.

Example: একটা ±10 V square wave (20 V peak-to-peak) একটা negative clamper-এ যায়। Ideal diode ধরো। Output range বের করো। Si diode দিয়ে আবার করো।

Ideal: উপরের মাথা 0 V-এ নামে। Peak-to-peak 20 V-ই থাকে। তাই output 0 V থেকে −20 V।

Si diode: capacitor charge হয় 10 − 0.7 = 9.3 V পর্যন্ত। Output = input − 9.3 → +0.7 V থেকে −19.3 V। এখনো 20 V peak-to-peak।

Positive clamper (ideal) হলে output হতো 0 V থেকে +20 V।

Biased positive clipper (VB = 3 V, Si) +3.7 V +10 −10 0 grey dashed = input, blue = output Negative clamper (ideal diode) +10 0 −10 0 −20 input output (same 20 V p-p, shifted down)
Left: biased clipper — the part above 3.7 V is cut off. Right: negative clamper — the whole square wave is shifted down; the peak-to-peak value (20 V) does not change.বামে: biased clipper — 3.7 V-এর উপরের অংশ কেটে গেছে। ডানে: negative clamper — পুরো square wave নিচে সরে গেছে; peak-to-peak value (20 V) বদলায়নি।
Clipper vs Clamper (one line): Clipper cuts the wave (shape changes, no capacitor needed). Clamper shifts the wave (shape and peak-to-peak stay the same, capacitor needed).
Clipper বনাম Clamper (এক লাইনে): Clipper wave কাটে (আকার বদলায়, capacitor লাগে না)। Clamper wave সরায় (আকার আর peak-to-peak একই থাকে, capacitor লাগে)।

4. Zener and Special Diodes4. Zener আর Special Diodes

Zener DiodeZener Diode

A Zener diode is a diode made to work safely in reverse breakdown. It is heavily doped, so breakdown happens at a fixed, sharp voltage called VZ (for example 5.1 V, 9 V, 12 V). In breakdown, the voltage across it stays almost equal to VZ even when the current changes a lot. That is exactly what a voltage regulator needs.

  • In forward bias, a Zener acts like a normal diode (0.7 V).
  • In reverse bias below VZ, it is OFF (like an open).
  • In reverse bias at VZ, it holds VZ constant. It must carry at least a small current IZ(min) (also called IZK, the knee current) to stay in regulation, and not more than IZM = PZ(max)/VZ to stay safe.

Zener diode এমন একটা diode যেটা নিরাপদে reverse breakdown-এ কাজ করার জন্য বানানো। এটা heavily doped, তাই একটা fixed আর sharp voltage-এ breakdown হয়, যাকে বলে VZ (যেমন 5.1 V, 9 V, 12 V)। Breakdown-এ current অনেক বদলালেও এর voltage প্রায় VZ-ই থাকে। একটা voltage regulator-এর ঠিক এটাই দরকার।

  • Forward bias-এ Zener সাধারণ diode-এর মতো (0.7 V)।
  • Reverse bias-এ VZ-এর নিচে এটা OFF (open-এর মতো)।
  • Reverse bias-এ VZ-এ পৌঁছালে এটা VZ স্থির রাখে। Regulation-এ থাকতে এর মধ্যে কমপক্ষে একটা ছোট current IZ(min) (একে IZK, knee current-ও বলে) থাকতে হবে, আর নিরাপদ থাকতে IZM = PZ(max)/VZ-এর বেশি হওয়া যাবে না।
R Vin + IR IZ IL VZ RL Vout = VZ ; IR = IZ + IL
Zener shunt regulator. The Zener is reverse biased (cathode to +). Extra current goes through the Zener, so the load voltage stays at VZ.Zener shunt regulator। Zener reverse biased (cathode যায় + এ)। বাড়তি current Zener দিয়ে যায়, তাই load voltage VZ-এ থাকে।
\[ I_R = \frac{V_{in} - V_Z}{R}, \qquad I_L = \frac{V_Z}{R_L}, \qquad I_Z = I_R - I_L \]

Step 0 — always check first if the Zener is ON. Remove the Zener and find the voltage across RL: VL = Vin × RL/(R + RL). If VL ≥ VZ, the Zener is ON and Vout = VZ. If VL < VZ, the Zener is OFF and Vout = VL (no regulation).

Design formula for the series resistor (worst case: lowest Vin, largest load current):

Step 0 — সবসময় আগে check করো Zener ON কিনা। Zener সরিয়ে RL-এর voltage বের করো: VL = Vin × RL/(R + RL)। VL ≥ VZ হলে Zener ON আর Vout = VZ। VL < VZ হলে Zener OFF আর Vout = VL (কোনো regulation নেই)।

Series resistor-এর design formula (worst case: সবচেয়ে কম Vin, সবচেয়ে বেশি load current):

\[ R = \frac{V_{in(min)} - V_Z}{I_{L(max)} + I_{Z(min)}}, \qquad R_{L(min)} = \frac{R\,V_Z}{V_{in} - V_Z}\ \ (\text{taking } I_{Z(min)} \approx 0) \]
Example (analysis): Vin = 20 V, R = 1 kΩ, VZ = 10 V. Find Vout and IZ for (a) RL = 2 kΩ, (b) RL = 500 Ω.

(a) Check: VL = 20 × 2/(1 + 2) = 13.3 V ≥ 10 V → Zener ON. Vout = 10 V.
IR = (20 − 10)/1 kΩ = 10 mA. IL = 10/2 kΩ = 5 mA. IZ = 10 − 5 = 5 mA.

(b) Check: VL = 20 × 0.5/(1 + 0.5) = 6.67 V < 10 V → Zener is OFF! Vout = 6.67 V, IZ = 0. The load is too heavy.

Minimum load for regulation: RL(min) = 1000 × 10/(20 − 10) = 1 kΩ.

Line regulation check: with RL = 2 kΩ, if Vin goes from 18 V to 25 V, IR goes from 8 mA to 15 mA, so IZ goes from 3 mA to 10 mA — but Vout stays 10 V. The Zener "absorbs" the change.

Example (analysis): Vin = 20 V, R = 1 kΩ, VZ = 10 V। (a) RL = 2 kΩ, (b) RL = 500 Ω হলে Vout আর IZ বের করো।

(a) Check: VL = 20 × 2/(1 + 2) = 13.3 V ≥ 10 V → Zener ON। Vout = 10 V।
IR = (20 − 10)/1 kΩ = 10 mA। IL = 10/2 kΩ = 5 mA। IZ = 10 − 5 = 5 mA।

(b) Check: VL = 20 × 0.5/(1 + 0.5) = 6.67 V < 10 V → Zener OFF! Vout = 6.67 V, IZ = 0। Load অনেক বেশি ভারী।

Regulation-এর জন্য minimum load: RL(min) = 1000 × 10/(20 − 10) = 1 kΩ।

Line regulation check: RL = 2 kΩ রেখে Vin 18 V থেকে 25 V হলে IR 8 mA থেকে 15 mA হয়, তাই IZ 3 mA থেকে 10 mA হয় — কিন্তু Vout থাকে 10 V। Zener পরিবর্তনটা "শুষে নেয়"।

Example (design, load regulation): Vin = 15 V, VZ = 9 V. The load current can change from 0 to 20 mA. The Zener needs IZ(min) = 5 mA. Find R, the Zener current range, and the Zener power rating.

R = (15 − 9)/(20 mA + 5 mA) = 6/0.025 = 240 Ω.

IR = 6/240 = 25 mA (fixed, since Vin and VZ are fixed).

Full load (IL = 20 mA): IZ = 25 − 20 = 5 mA. No load (IL = 0): IZ = 25 − 0 = 25 mA.

So the Zener current range is 5 mA to 25 mA. Max Zener power = 9 × 0.025 = 225 mW → choose a 0.5 W Zener for safety.

Example (design, load regulation): Vin = 15 V, VZ = 9 V। Load current 0 থেকে 20 mA পর্যন্ত বদলাতে পারে। Zener-এর দরকার IZ(min) = 5 mA। R, Zener current range আর Zener power rating বের করো।

R = (15 − 9)/(20 mA + 5 mA) = 6/0.025 = 240 Ω।

IR = 6/240 = 25 mA (fixed, কারণ Vin আর VZ fixed)।

Full load (IL = 20 mA): IZ = 25 − 20 = 5 mA। No load (IL = 0): IZ = 25 − 0 = 25 mA।

তাই Zener current range 5 mA থেকে 25 mA। Max Zener power = 9 × 0.025 = 225 mW → নিরাপত্তার জন্য 0.5 W Zener নাও।

Key idea: In a Zener regulator, IR is almost fixed. The Zener and the load share it. When the load takes less, the Zener takes more. So the worst case for Zener power is no load (and highest Vin).
মূল ধারণা: Zener regulator-এ IR প্রায় fixed। Zener আর load এটা ভাগ করে নেয়। Load কম নিলে Zener বেশি নেয়। তাই Zener power-এর worst case হলো no load (আর সবচেয়ে বেশি Vin)।

LED (Light Emitting Diode)LED (Light Emitting Diode)

An LED gives light when forward biased. Electrons fall from the CB to the VB and give out their energy as light. The colour depends on the band gap of the material (GaAs, GaAsP, GaP, InGaN), not silicon. A bigger band gap gives a bluer colour and a bigger forward voltage.

LED forward biased হলে আলো দেয়। Electron CB থেকে VB-তে পড়ে আর তার energy আলো হিসেবে দেয়। রং নির্ভর করে material-এর band gap-এর উপর (GaAs, GaAsP, GaP, InGaN), silicon না। Band gap যত বড়, রং তত নীলের দিকে আর forward voltage তত বেশি।

LED colourLED-এর রংTypical forward voltageTypical forward voltageMaterial (typical)Material (typical)
Infrared (IR)1.2 – 1.5 VGaAs
Redলাল (Red)1.8 – 2.0 VGaAsP, AlGaAs
Yellow / Orangeহলুদ / কমলা2.0 – 2.2 VGaAsP
Greenসবুজ (Green)2.0 – 3.0 VGaP, InGaN
Blue / Whiteনীল / সাদা3.0 – 3.4 VInGaN
\[ R_{series} = \frac{V_{supply} - V_{LED}}{I_{LED}} \]
Example: (a) A red LED (2 V) runs from a 5 V Arduino pin at 20 mA. Find R. (b) A blue LED (3.2 V) runs from 12 V at 15 mA.

(a) R = (5 − 2)/0.02 = 150 Ω.

(b) R = (12 − 3.2)/0.015 = 586.7 Ω. The nearest standard value above it is 620 Ω. Then I = 8.8/620 = 14.2 mA — safe.

Example: (a) একটা red LED (2 V) 5 V Arduino pin থেকে 20 mA-তে চলবে। R বের করো। (b) একটা blue LED (3.2 V) 12 V থেকে 15 mA-তে চলবে।

(a) R = (5 − 2)/0.02 = 150 Ω।

(b) R = (12 − 3.2)/0.015 = 586.7 Ω। এর উপরের সবচেয়ে কাছের standard value 620 Ω। তখন I = 8.8/620 = 14.2 mA — নিরাপদ।

Other Special Diodesঅন্যান্য Special Diode

DiodeBias usedকোন biasKey ideaমূল ধারণাMain useপ্রধান ব্যবহার
ZenerReverse (breakdown)Holds a fixed voltage VZএকটা fixed voltage VZ ধরে রাখেVoltage regulator, referenceVoltage regulator, reference
LEDForwardElectron–hole recombination gives lightElectron–hole recombination থেকে আলোIndicators, displays, lighting, IR remoteIndicator, display, lighting, IR remote
PhotodiodeReverseLight makes carriers → reverse current grows with lightআলো carrier তৈরি করে → আলো বাড়লে reverse current বাড়েLight sensors, optical-fibre receivers, barcode readersLight sensor, optical-fibre receiver, barcode reader
Solar cellNo external biasবাইরের bias নেইLight → voltage and power (≈ 0.5–0.6 V per Si cell)আলো → voltage আর power (প্রতি Si cell-এ ≈ 0.5–0.6 V)Solar panelsSolar panel
Varactor (varicap)ReverseDepletion width changes with voltage → capacitance changesVoltage-এ depletion width বদলায় → capacitance বদলায়Tuning in radio/TV, VCORadio/TV tuning, VCO
SchottkyForwardMetal–semiconductor junction; only majority carriers; low drop (0.2–0.4 V); very fastMetal–semiconductor junction; শুধু majority carrier; কম drop (0.2–0.4 V); খুব fastSMPS, high-speed switching, Schottky TTL (74LS)SMPS, high-speed switching, Schottky TTL (74LS)
TunnelForward (small V)Very heavy doping; negative resistance region (current falls as voltage rises)খুব heavy doping; negative resistance region (voltage বাড়লে current কমে)Microwave oscillators, very fast switchesMicrowave oscillator, খুব fast switch
Example (varactor): A varactor has C = 40 pF at a reverse voltage of 4 V. Assume C ∝ 1/√VR. Find C at 16 V.

C2 = C1 × √(V1/V2) = 40 × √(4/16) = 40 × 0.5 = 20 pF. More reverse voltage → wider depletion region → less capacitance.

Example (varactor): একটা varactor-এর 4 V reverse voltage-এ C = 40 pF। ধরো C ∝ 1/√VR। 16 V-এ C কত?

C2 = C1 × √(V1/V2) = 40 × √(4/16) = 40 × 0.5 = 20 pF। বেশি reverse voltage → চওড়া depletion region → কম capacitance।

Example (solar panel): Each Si solar cell gives 0.5 V. How many cells in series give an 18 V open-circuit panel (a typical "12 V" panel)?

N = 18 / 0.5 = 36 cells in series. Cells in series add voltage; cells in parallel add current.

Example (solar panel): প্রতিটা Si solar cell 0.5 V দেয়। 18 V open-circuit panel (সাধারণ "12 V" panel) পেতে series-এ কয়টা cell লাগবে?

N = 18 / 0.5 = 36টা cell series-এ। Series-এ cell দিলে voltage যোগ হয়; parallel-এ দিলে current যোগ হয়।

MCQ quick list: Negative resistance → tunnel diode. Voltage-controlled capacitor → varactor. Lowest forward drop and fastest switching → Schottky. Works in reverse breakdown → Zener. Light sensor in reverse bias → photodiode. Light emitter in forward bias → LED.
MCQ quick list: Negative resistance → tunnel diode। Voltage দিয়ে control করা capacitor → varactor। সবচেয়ে কম forward drop আর সবচেয়ে fast switching → Schottky। Reverse breakdown-এ কাজ করে → Zener। Reverse bias-এ light sensor → photodiode। Forward bias-এ আলো দেয় → LED।

5. Bipolar Junction Transistor (BJT)5. Bipolar Junction Transistor (BJT)

A transistor is a device where a small signal controls a big current. It can work as an amplifier (make a signal bigger) or as a switch (ON/OFF — the basis of all digital logic).

A BJT has three doped layers and two junctions. "Bipolar" means both electrons and holes carry current. There are two types: npn and pnp. The three terminals are:

  • Emitter (E) — heavily doped. It "emits" (sends) carriers into the base.
  • Base (B) — very thin and lightly doped. It controls the flow.
  • Collector (C) — moderately doped and the largest region (it must get rid of heat). It "collects" the carriers.

Transistor এমন একটা device যেখানে ছোট একটা signal বড় একটা current-কে control করে। এটা amplifier (signal বড় করা) বা switch (ON/OFF — সব digital logic-এর ভিত্তি) হিসেবে কাজ করতে পারে।

BJT-তে তিনটা doped layer আর দুইটা junction থাকে। "Bipolar" মানে electron আর hole দুইটাই current বহন করে। দুই ধরনের আছে: npn আর pnp। তিনটা terminal:

  • Emitter (E) — heavily doped। এটা base-এ carrier "emit" করে (পাঠায়)।
  • Base (B) — খুব পাতলা আর lightly doped। এটা flow control করে।
  • Collector (C) — moderately doped আর সবচেয়ে বড় region (তাপ বের করতে হয়)। এটা carrier "collect" করে।
CBE CBE npn pnp arrow points OUT (Not Pointing iN) arrow Points iN Proudly n⁺pn E (heavy)BC (large) npn structure p⁺np E (heavy)BC (large) pnp structure
BJT symbols (left) and layer structure (right). The arrow is always on the emitter and shows the direction of conventional current. The base is very thin.BJT symbol (বামে) আর layer structure (ডানে)। Arrow সবসময় emitter-এ থাকে আর conventional current-এর দিক দেখায়। Base খুব পাতলা।
Several real discrete transistors in different packages
Real transistors in different packages (TO-92, TO-220, TO-3 and others). (Wikimedia Commons)বিভিন্ন package-এ আসল transistor (TO-92, TO-220, TO-3 ইত্যাদি)। (Wikimedia Commons)

How an npn BJT Works (in active mode)npn BJT কীভাবে কাজ করে (active mode-এ)

  1. The base–emitter (BE) junction is forward biased (VBE ≈ 0.7 V). So many electrons flow from the emitter into the base.
  2. The base is very thin and has few holes. So only a few electrons (about 1%) recombine there. That small flow is the base current IB.
  3. The base–collector (BC) junction is reverse biased. Its strong field pulls almost all (about 99%) of the electrons into the collector. That is the collector current IC.

So a small IB controls a large IC. The ratio is the current gain β.

  1. Base–emitter (BE) junction forward biased (VBE ≈ 0.7 V)। তাই emitter থেকে অনেক electron base-এ ঢোকে।
  2. Base খুব পাতলা আর এতে hole কম। তাই মাত্র অল্প কিছু electron (প্রায় 1%) সেখানে recombine করে। ওই ছোট flow-টাই base current IB।
  3. Base–collector (BC) junction reverse biased। এর শক্তিশালী field প্রায় সব (প্রায় 99%) electron-কে collector-এ টেনে নেয়। এটাই collector current IC।

তাই ছোট IB বড় IC-কে control করে। এই অনুপাতই current gain β।

Current Relations: α and βCurrent-এর সম্পর্ক: α আর β

\[ I_E = I_C + I_B, \qquad \beta = \frac{I_C}{I_B}, \qquad \alpha = \frac{I_C}{I_E} \]
\[ \alpha = \frac{\beta}{\beta + 1}, \qquad \beta = \frac{\alpha}{1 - \alpha}, \qquad I_E = (\beta + 1) I_B \]

β (also written hFE) is usually 50 to 300. α is always a little less than 1 (like 0.98 to 0.997), because IC is always a bit less than IE.

Proof of α = β/(β+1): α = IC/IE = IC/(IC + IB). Divide top and bottom by IB: α = β/(β + 1).

β (hFE-ও লেখা হয়) সাধারণত 50 থেকে 300। α সবসময় 1-এর একটু কম (যেমন 0.98 থেকে 0.997), কারণ IC সবসময় IE-এর চেয়ে একটু কম।

α = β/(β+1)-এর প্রমাণ: α = IC/IE = IC/(IC + IB)। উপরে-নিচে IB দিয়ে ভাগ করো: α = β/(β + 1)।

Example: A BJT has β = 100 and IB = 20 µA. Find IC, IE and α.

IC = β IB = 100 × 20 µA = 2 mA.

IE = IC + IB = 2 mA + 0.02 mA = 2.02 mA.

α = 100/101 = 0.990. Check: IC/IE = 2/2.02 = 0.990 ✓.

Example: একটা BJT-এর β = 100 আর IB = 20 µA। IC, IE আর α বের করো।

IC = β IB = 100 × 20 µA = 2 mA।

IE = IC + IB = 2 mA + 0.02 mA = 2.02 mA।

α = 100/101 = 0.990। Check: IC/IE = 2/2.02 = 0.990 ✓।

Example: α = 0.98. Find β. And if α = 0.995?

β = 0.98/(1 − 0.98) = 0.98/0.02 = 49. For α = 0.995: β = 0.995/0.005 = 199.

See how a tiny change in α makes a big change in β.

Example: α = 0.98। β কত? আর α = 0.995 হলে?

β = 0.98/(1 − 0.98) = 0.98/0.02 = 49। α = 0.995 হলে: β = 0.995/0.005 = 199।

দেখো, α-তে সামান্য পরিবর্তন β-তে অনেক বড় পরিবর্তন আনে।

MCQ trap: α is always less than 1; β is much greater than 1. If an option says α = 1.02 or β = 0.98, it is wrong. Also, leakage: ICEO = (β + 1) ICBO. With ICBO = 10 nA and β = 100, ICEO = 101 × 10 nA ≈ 1.01 µA.
MCQ trap: α সবসময় 1-এর কম; β, 1-এর চেয়ে অনেক বড়। কোনো option-এ α = 1.02 বা β = 0.98 থাকলে সেটা ভুল। আরও, leakage: ICEO = (β + 1) ICBO। ICBO = 10 nA আর β = 100 হলে ICEO = 101 × 10 nA ≈ 1.01 µA।

Regions of OperationOperation-এর Region

RegionBE junctionBC junctionBehaviourআচরণUsed asব্যবহার
CutoffReverse (or < 0.7 V)ReverseIC ≈ 0 — like an open switchIC ≈ 0 — খোলা switch-এর মতোSwitch OFFSwitch OFF
ActiveForwardReverseIC = β IBAmplifierAmplifier
SaturationForwardForwardVCE ≈ 0.2 V, IC < β IB — like a closed switchVCE ≈ 0.2 V, IC < β IB — বন্ধ switch-এর মতোSwitch ONSwitch ON
Reverse activeReverseForwardVery low gainখুব কম gainRarely usedকমই ব্যবহার হয়
Memory trick: Active = "F-R" (Forward–Reverse), Saturation = "F-F", Cutoff = "R-R". For digital logic, the BJT only jumps between cutoff (0) and saturation (1).
মনে রাখার কৌশল: Active = "F-R" (Forward–Reverse), Saturation = "F-F", Cutoff = "R-R"। Digital logic-এ BJT শুধু cutoff (0) আর saturation (1)-এর মধ্যে লাফায়।

Three Configurations: CE, CB, CCতিনটা Configuration: CE, CB, CC

The name tells which terminal is common to input and output (usually grounded for AC).

নামটা বলে কোন terminal input আর output দুইটার জন্য common (সাধারণত AC-র জন্য ground করা)।

PropertyPropertyCommon Emitter (CE)Common Base (CB)Common Collector (CC) / Emitter follower
Input / OutputInput / OutputB / CE / CB / E
Current gainCurrent gainHigh (β)বেশি (β)≈ α (less than 1)≈ α (1-এর কম)High (β + 1)বেশি (β + 1)
Voltage gainVoltage gainHighবেশিHighবেশি≈ 1 (slightly less)≈ 1 (একটু কম)
Power gainPower gainHighestসবচেয়ে বেশিMediumমাঝারিLowকম
Input impedanceInput impedanceMedium (~1 kΩ)মাঝারি (~1 kΩ)Very low (~20 Ω)খুব কম (~20 Ω)Very highখুব বেশি
Output impedanceOutput impedanceMedium–highমাঝারি–বেশিVery highখুব বেশিVery lowখুব কম
Phase shiftPhase shift180°0°0°
Main useপ্রধান ব্যবহারGeneral amplifierসাধারণ amplifierHigh-frequency (RF) amplifierHigh-frequency (RF) amplifierBuffer, impedance matchingBuffer, impedance matching
MCQ favourites: Only CE gives 180° phase shift (it inverts). CC has voltage gain ≈ 1 and is used as a buffer. CB has current gain < 1 and the lowest input impedance.
MCQ-এর প্রিয় প্রশ্ন: শুধু CE 180° phase shift দেয় (invert করে)। CC-র voltage gain ≈ 1, buffer হিসেবে ব্যবহার হয়। CB-র current gain < 1 আর input impedance সবচেয়ে কম।

DC Biasing — Setting the Q-pointDC Biasing — Q-point ঠিক করা

To use a BJT as an amplifier, we first set a steady DC operating point, called the Q-point (quiescent point): the values of IC and VCE with no signal. It should be in the middle of the active region so the signal can swing up and down without clipping.

BJT-কে amplifier হিসেবে ব্যবহার করতে আগে একটা স্থির DC operating point ঠিক করতে হয়, যাকে বলে Q-point (quiescent point): কোনো signal না থাকলে IC আর VCE-এর মান। এটা active region-এর মাঝামাঝি থাকা উচিত, যাতে signal clipping ছাড়া উপরে-নিচে দুলতে পারে।

(a) Fixed Bias(a) Fixed Bias

A resistor RB goes from VCC to the base. RC goes from VCC to the collector. Emitter is grounded.

একটা resistor RB VCC থেকে base-এ যায়। RC VCC থেকে collector-এ যায়। Emitter ground-এ।

\[ I_B = \frac{V_{CC} - V_{BE}}{R_B}, \qquad I_C = \beta I_B, \qquad V_{CE} = V_{CC} - I_C R_C \]
Example: VCC = 12 V, RB = 470 kΩ, RC = 2.2 kΩ, β = 100, VBE = 0.7 V. Find the Q-point.

IB = (12 − 0.7)/470 kΩ = 11.3/470000 = 24.0 µA.

IC = 100 × 24.0 µA = 2.40 mA.

VCE = 12 − 2.40 mA × 2.2 kΩ = 12 − 5.29 = 6.71 V.

VCE is well above 0.2 V, so the BJT is in the active region. Q-point = (6.71 V, 2.40 mA).

Problem with fixed bias: if another transistor has β = 200, then IC = 4.81 mA and VCE = 12 − 4.81 × 2.2 = 1.42 V — almost in saturation! The Q-point depends strongly on β, which changes a lot from part to part and with temperature.

Example: VCC = 12 V, RB = 470 kΩ, RC = 2.2 kΩ, β = 100, VBE = 0.7 V। Q-point বের করো।

IB = (12 − 0.7)/470 kΩ = 11.3/470000 = 24.0 µA।

IC = 100 × 24.0 µA = 2.40 mA।

VCE = 12 − 2.40 mA × 2.2 kΩ = 12 − 5.29 = 6.71 V।

VCE 0.2 V-এর অনেক উপরে, তাই BJT active region-এ। Q-point = (6.71 V, 2.40 mA)।

Fixed bias-এর সমস্যা: অন্য একটা transistor-এর β = 200 হলে IC = 4.81 mA আর VCE = 12 − 4.81 × 2.2 = 1.42 V — প্রায় saturation! Q-point β-এর উপর অনেক নির্ভর করে, আর β এক part থেকে আরেক part-এ আর temperature-এ অনেক বদলায়।

Load LineLoad Line

From VCE = VCC − ICRC, all possible (VCE, IC) points lie on a straight line called the DC load line. Its two ends:

  • Saturation end (VCE = 0): IC(sat) = VCC/RC = 12/2.2k = 5.45 mA.
  • Cutoff end (IC = 0): VCE(off) = VCC = 12 V.

The Q-point is where the load line meets the transistor curve for the actual IB.

VCE = VCC − ICRC থেকে, সম্ভাব্য সব (VCE, IC) বিন্দু একটা সরলরেখায় থাকে, যাকে বলে DC load line। এর দুই মাথা:

  • Saturation মাথা (VCE = 0): IC(sat) = VCC/RC = 12/2.2k = 5.45 mA।
  • Cutoff মাথা (IC = 0): VCE(off) = VCC = 12 V।

আসল IB-এর transistor curve যেখানে load line-কে ছেদ করে, সেটাই Q-point।

VCE (V) IC (mA) 10 µA 20 µA 30 µA 40 µA 48 µA Q (6.71 V, 2.40 mA), β = 100 Q′ (1.42 V, 4.81 mA) if β = 200 5.45 12 cutoff region saturation
DC load line for VCC = 12 V, RC = 2.2 kΩ. The blue Q-point is healthy (middle of active region). With β = 200 in fixed bias, it jumps to Q′, close to saturation.VCC = 12 V, RC = 2.2 kΩ-এর DC load line। নীল Q-point ঠিক আছে (active region-এর মাঝে)। Fixed bias-এ β = 200 হলে এটা লাফ দিয়ে Q′-তে যায়, saturation-এর কাছে।

(b) Voltage-Divider Bias (the stable one)(b) Voltage-Divider Bias (stable টা)

Two resistors R1 (top) and R2 (bottom) set the base voltage. An emitter resistor RE gives negative feedback: if IC tries to rise, VE rises, VBE falls, and IC is pulled back. So the Q-point hardly depends on β. This is the most used bias circuit.

Approximate method (valid when βRE ≥ 10R2):

দুইটা resistor R1 (উপরে) আর R2 (নিচে) base voltage ঠিক করে। একটা emitter resistor RE negative feedback দেয়: IC বাড়তে চাইলে VE বাড়ে, VBE কমে, আর IC আবার কমে আসে। তাই Q-point প্রায় β-এর উপর নির্ভর করে না। এটাই সবচেয়ে বেশি ব্যবহৃত bias circuit।

Approximate method (βRE ≥ 10R2 হলে চলে):

\[ V_B = V_{CC}\frac{R_2}{R_1 + R_2}, \quad V_E = V_B - 0.7, \quad I_C \approx I_E = \frac{V_E}{R_E}, \quad V_{CE} = V_{CC} - I_C(R_C + R_E) \]
Example: VCC = 12 V, R1 = 47 kΩ, R2 = 10 kΩ, RC = 2.2 kΩ, RE = 1 kΩ, β = 150. Find the Q-point.

Check: βRE = 150 kΩ ≥ 10R2 = 100 kΩ ✓ → approximate method is fine.

VB = 12 × 10/(47 + 10) = 2.11 V. VE = 2.11 − 0.7 = 1.41 V.

IE = 1.41 V/1 kΩ = 1.41 mA ≈ IC.

VCE = 12 − 1.41 × (2.2 + 1) = 12 − 4.50 = 7.50 V. Active ✓.

Exact (Thevenin) method gives IC = 1.32 mA, VCE = 7.76 V. If β goes to 300, exact IC = 1.36 mA — only a 3% change. Compare with fixed bias, where doubling β doubled IC!

Bonus (small-signal gain): re = 26 mV/IE = 26/1.41 ≈ 18.5 Ω. If RE is bypassed by a capacitor, the CE voltage gain Av ≈ −RC/re = −2200/18.5 ≈ −119 (minus = 180° phase shift).

Example: VCC = 12 V, R1 = 47 kΩ, R2 = 10 kΩ, RC = 2.2 kΩ, RE = 1 kΩ, β = 150। Q-point বের করো।

Check: βRE = 150 kΩ ≥ 10R2 = 100 kΩ ✓ → approximate method চলবে।

VB = 12 × 10/(47 + 10) = 2.11 V। VE = 2.11 − 0.7 = 1.41 V।

IE = 1.41 V/1 kΩ = 1.41 mA ≈ IC।

VCE = 12 − 1.41 × (2.2 + 1) = 12 − 4.50 = 7.50 V। Active ✓।

Exact (Thevenin) method দিলে IC = 1.32 mA, VCE = 7.76 V। β 300 হলে exact IC = 1.36 mA — মাত্র 3% পরিবর্তন। Fixed bias-এর সাথে তুলনা করো, যেখানে β দ্বিগুণ হলে IC-ও দ্বিগুণ হয়েছিল!

Bonus (small-signal gain): re = 26 mV/IE = 26/1.41 ≈ 18.5 Ω। RE একটা capacitor দিয়ে bypass করা থাকলে CE voltage gain Av ≈ −RC/re = −2200/18.5 ≈ −119 (minus = 180° phase shift)।

BJT as a SwitchSwitch হিসেবে BJT

For a switch, we want only two states: cutoff (OFF, IC = 0, VCE = VCC) and saturation (ON, VCE(sat) ≈ 0.2 V). To make sure the BJT is fully ON, the base current must be large enough:

Switch-এর জন্য আমরা শুধু দুইটা state চাই: cutoff (OFF, IC = 0, VCE = VCC) আর saturation (ON, VCE(sat) ≈ 0.2 V)। BJT পুরোপুরি ON নিশ্চিত করতে base current যথেষ্ট বড় হতে হবে:

\[ I_{C(sat)} = \frac{V_{CC} - V_{CE(sat)}}{R_C}, \qquad \text{saturation if } \ I_B > \frac{I_{C(sat)}}{\beta} \]
Example: VCC = 5 V, RC = 1 kΩ, β = 100, VCE(sat) = 0.2 V. The input is a 5 V logic signal through RB. Find the largest RB that still saturates the BJT. Is RB = 10 kΩ OK?

IC(sat) = (5 − 0.2)/1 kΩ = 4.8 mA.

IB(min) = 4.8 mA/100 = 48 µA.

RB(max) = (5 − 0.7)/48 µA = 4.3/0.000048 = 89.6 kΩ.

With RB = 10 kΩ: IB = 4.3/10k = 0.43 mA ≈ 9 × 48 µA → hard saturation ✓. Designers use extra base current like this to be safe.

Input 5 V (1) → BJT ON → output VCE ≈ 0.2 V (0). Input 0 V (0) → BJT OFF → output = 5 V (1). This circuit is a NOT gate (RTL inverter)!

Example: VCC = 5 V, RC = 1 kΩ, β = 100, VCE(sat) = 0.2 V। Input হলো RB দিয়ে আসা 5 V logic signal। BJT-কে saturation-এ রাখে এমন সবচেয়ে বড় RB বের করো। RB = 10 kΩ কি ঠিক আছে?

IC(sat) = (5 − 0.2)/1 kΩ = 4.8 mA।

IB(min) = 4.8 mA/100 = 48 µA।

RB(max) = (5 − 0.7)/48 µA = 4.3/0.000048 = 89.6 kΩ।

RB = 10 kΩ হলে: IB = 4.3/10k = 0.43 mA ≈ 9 × 48 µA → hard saturation ✓। নিরাপদ থাকতে designer-রা এভাবে বাড়তি base current দেয়।

Input 5 V (1) → BJT ON → output VCE ≈ 0.2 V (0)। Input 0 V (0) → BJT OFF → output = 5 V (1)। এই circuit-টা একটা NOT gate (RTL inverter)!

How to check saturation in an exam: Assume active. Find IC = βIB and VCE. If VCE comes out below 0.2 V (or negative!), the assumption is wrong: the BJT is saturated. Then use VCE = 0.2 V and IC = IC(sat).
Exam-এ saturation কীভাবে check করবে: Active ধরে নাও। IC = βIB আর VCE বের করো। VCE যদি 0.2 V-এর নিচে (বা negative!) আসে, ধারণা ভুল: BJT saturated। তখন VCE = 0.2 V আর IC = IC(sat) ব্যবহার করো।

6. FET, MOSFET and CMOS6. FET, MOSFET আর CMOS

A Field-Effect Transistor (FET) is controlled by a voltage on its gate, not by a current. The gate voltage makes an electric field. The field opens or squeezes a channel for current. FETs are unipolar: only one kind of carrier (electrons in n-channel, holes in p-channel) carries the current.

Terminals: Gate (G) ≈ base, Drain (D) ≈ collector, Source (S) ≈ emitter.

Field-Effect Transistor (FET) gate-এর voltage দিয়ে control হয়, current দিয়ে না। Gate voltage একটা electric field তৈরি করে। এই field current-এর জন্য একটা channel খুলে দেয় বা চেপে সরু করে। FET হলো unipolar: মাত্র এক ধরনের carrier (n-channel-এ electron, p-channel-এ hole) current বহন করে।

Terminal: Gate (G) ≈ base, Drain (D) ≈ collector, Source (S) ≈ emitter।

JFET (Junction FET) — quick basicsJFET (Junction FET) — সংক্ষেপে

An n-channel JFET is a bar of n-type silicon (the channel) with p-type regions on its sides (the gate). The gate–channel junction is always kept reverse biased (VGS ≤ 0). A more negative VGS makes the depletion regions wider, so the channel gets narrower and ID drops. At VGS = VP (the pinch-off voltage), the channel is fully closed and ID = 0. A JFET is normally ON (it conducts at VGS = 0).

একটা n-channel JFET হলো n-type silicon-এর একটা bar (channel), যার দুই পাশে p-type region (gate)। Gate–channel junction সবসময় reverse biased রাখা হয় (VGS ≤ 0)। VGS যত negative, depletion region তত চওড়া, তাই channel সরু হয় আর ID কমে। VGS = VP (pinch-off voltage) হলে channel পুরো বন্ধ আর ID = 0। JFET normally ON (VGS = 0-তে conduct করে)।

\[ I_D = I_{DSS}\left(1 - \frac{V_{GS}}{V_P}\right)^2 \quad \text{(Shockley's equation for JFET)} \]
Example: A JFET has IDSS = 10 mA and VP = −4 V. Find ID at VGS = 0, −1 V, −2 V and −4 V.

VGS = 0: ID = 10(1 − 0)² = 10 mA (= IDSS, the maximum).

VGS = −1 V: ID = 10(1 − 0.25)² = 10 × 0.5625 = 5.625 mA.

VGS = −2 V: ID = 10(1 − 0.5)² = 2.5 mA.

VGS = −4 V: ID = 10(1 − 1)² = 0 (pinch-off).

Example: একটা JFET-এর IDSS = 10 mA আর VP = −4 V। VGS = 0, −1 V, −2 V আর −4 V-এ ID বের করো।

VGS = 0: ID = 10(1 − 0)² = 10 mA (= IDSS, সর্বোচ্চ)।

VGS = −1 V: ID = 10(1 − 0.25)² = 10 × 0.5625 = 5.625 mA।

VGS = −2 V: ID = 10(1 − 0.5)² = 2.5 mA।

VGS = −4 V: ID = 10(1 − 1)² = 0 (pinch-off)।

MOSFET StructureMOSFET-এর গঠন

MOSFET = Metal–Oxide–Semiconductor FET. It is the most-made device in history — a modern CPU has billions of them.

  • Start with a p-type substrate (body).
  • Make two heavily doped n⁺ regions: the source and the drain.
  • Grow a very thin layer of SiO₂ (oxide, an insulator) on top of the gap between them.
  • Put the gate (metal or polysilicon) on top of the oxide.

Because the gate sits on an insulator, no DC current flows into the gate. Input resistance is huge (10¹⁰–10¹⁵ Ω).

How an enhancement nMOS turns ON: put a positive VGS. It pushes holes away from the surface and pulls electrons toward it. When VGS passes the threshold voltage Vt (often 0.3–1 V), a thin layer of electrons forms under the oxide. This inversion layer is the n-channel that joins source and drain. Now current can flow.

MOSFET = Metal–Oxide–Semiconductor FET। ইতিহাসে সবচেয়ে বেশি তৈরি হওয়া device — একটা modern CPU-তে billion-এর বেশি MOSFET থাকে।

  • একটা p-type substrate (body) দিয়ে শুরু।
  • দুইটা heavily doped n⁺ region বানাও: source আর drain।
  • এদের মাঝের ফাঁকের উপরে SiO₂ (oxide, একটা insulator)-এর খুব পাতলা স্তর তৈরি করো।
  • Oxide-এর উপরে gate (metal বা polysilicon) বসাও।

Gate একটা insulator-এর উপরে বসে আছে, তাই gate-এ কোনো DC current ঢোকে না। Input resistance বিশাল (10¹⁰–10¹⁵ Ω)।

Enhancement nMOS কীভাবে ON হয়: positive VGS দাও। এটা surface থেকে hole সরিয়ে দেয় আর electron টেনে আনে। VGS যখন threshold voltage Vt (প্রায়ই 0.3–1 V) পার হয়, oxide-এর নিচে electron-এর একটা পাতলা স্তর তৈরি হয়। এই inversion layer-ই n-channel, যেটা source আর drain জোড়া দেয়। এখন current চলতে পারে।

TypeChannel at VGS = 0?VGS = 0-তে channel আছে?Vt (VGS(th))Turn ON byON করতেCarrierCarrier
n-channel enhancementNo (normally OFF)না (normally OFF)Positive (e.g. +1 V)Positive (যেমন +1 V)VGS > VtElectronsElectron
p-channel enhancementNo (normally OFF)না (normally OFF)Negative (e.g. −1 V)Negative (যেমন −1 V)VGS < VtHolesHole
n-channel depletionYes (normally ON)হ্যাঁ (normally ON)Negative (e.g. −3 V)Negative (যেমন −3 V)Already ON; negative VGS turns it OFFআগেই ON; negative VGS দিলে OFF হয়ElectronsElectron
p-channel depletionYes (normally ON)হ্যাঁ (normally ON)PositiveAlready ON; positive VGS turns it OFFআগেই ON; positive VGS দিলে OFF হয়HolesHole

Since electron mobility is about 2–3 times hole mobility, an nMOS is faster (or smaller for the same current) than a pMOS. Digital chips use enhancement MOSFETs, because "OFF when gate = 0" is exactly what logic needs.

Electron mobility hole mobility-র প্রায় 2–3 গুণ, তাই nMOS pMOS-এর চেয়ে fast (বা একই current-এর জন্য ছোট)। Digital chip-এ enhancement MOSFET ব্যবহার হয়, কারণ "gate = 0 হলে OFF" — logic-এর ঠিক এটাই দরকার।

Regions of an Enhancement nMOSEnhancement nMOS-এর Region

RegionConditionশর্তIDActs likeযেমন আচরণ
CutoffVGS < Vt0Open switchখোলা switch
Triode (linear / ohmic)VGS > Vt and VDS < VGS − Vt\( k\left[(V_{GS}-V_t)V_{DS} - \tfrac{1}{2}V_{DS}^2\right] \)Voltage-controlled resistor; closed switchVoltage-controlled resistor; বন্ধ switch
SaturationVGS > Vt and VDS ≥ VGS − Vt\( \tfrac{k}{2}(V_{GS}-V_t)^2 \)Current source; amplifierCurrent source; amplifier
\[ I_D = \frac{k}{2}\,(V_{GS} - V_t)^2 \quad \text{(saturation)}, \qquad k = \mu_n C_{ox}\frac{W}{L} \]
Name confusion alert: MOSFET "saturation" means the current is flat (amplifier region). This matches the BJT's active region, not the BJT's saturation! A MOSFET used as a closed switch is in the triode region.
নামের বিভ্রান্তি সাবধান: MOSFET-এর "saturation" মানে current সমান থাকে (amplifier region)। এটা BJT-এর active region-এর মতো, BJT-এর saturation-এর মতো না! বন্ধ switch হিসেবে MOSFET থাকে triode region-এ।
Example 1: An nMOS has k = 2 mA/V² and Vt = 1 V. VGS = 3 V. VDD = 12 V with RD = 2 kΩ. Find ID and VDS. Check the region.

Assume saturation: ID = (2/2)(3 − 1)² = 1 × 4 = 4 mA.

VDS = 12 − 4 mA × 2 kΩ = 12 − 8 = 4 V.

Check: VGS − Vt = 2 V. Is VDS ≥ 2 V? 4 ≥ 2 ✓ → saturation is correct.

Example 1: একটা nMOS-এর k = 2 mA/V² আর Vt = 1 V। VGS = 3 V। VDD = 12 V, RD = 2 kΩ। ID আর VDS বের করো। Region check করো।

Saturation ধরি: ID = (2/2)(3 − 1)² = 1 × 4 = 4 mA।

VDS = 12 − 4 mA × 2 kΩ = 12 − 8 = 4 V।

Check: VGS − Vt = 2 V। VDS ≥ 2 V? 4 ≥ 2 ✓ → saturation ঠিক।

Example 2 (when the guess fails): Same MOSFET, but RD = 3 kΩ.

Assume saturation: ID = 4 mA → VDS = 12 − 4 × 3 = 0 V. Check: 0 ≥ 2? ✗. So it is in triode.

Triode: ID = 2[(2)VDS − VDS²/2] = 4VDS − VDS² (mA). Also ID = (12 − VDS)/3 (mA).

Set equal: (12 − V)/3 = 4V − V² → 12 − V = 12V − 3V² → 3V² − 13V + 12 = 0.

V = (13 ± √(169 − 144))/6 = (13 ± 5)/6 → V = 3 V or 1.33 V. V = 3 V is not < 2 V, so reject it. So VDS = 1.33 V, ID = (12 − 1.33)/3 = 3.56 mA.

Example 2 (অনুমান ভুল হলে): একই MOSFET, কিন্তু RD = 3 kΩ।

Saturation ধরি: ID = 4 mA → VDS = 12 − 4 × 3 = 0 V। Check: 0 ≥ 2? ✗। তাই এটা triode-এ।

Triode: ID = 2[(2)VDS − VDS²/2] = 4VDS − VDS² (mA)। আবার ID = (12 − VDS)/3 (mA)।

সমান করি: (12 − V)/3 = 4V − V² → 12 − V = 12V − 3V² → 3V² − 13V + 12 = 0।

V = (13 ± √(169 − 144))/6 = (13 ± 5)/6 → V = 3 V বা 1.33 V। V = 3 V, 2 V-এর কম না, তাই বাদ। তাই VDS = 1.33 V, ID = (12 − 1.33)/3 = 3.56 mA।

BJT vs MOSFETBJT বনাম MOSFET

Featureবৈশিষ্ট্যBJTMOSFET
Controlled byকী দিয়ে controlCurrent (IB)Current (IB)Voltage (VGS)Voltage (VGS)
CarriersCarrierBipolar (electrons + holes)Bipolar (electron + hole)Unipolar (one type)Unipolar (এক ধরনের)
Input impedanceInput impedanceLow–medium (kΩ)কম–মাঝারি (kΩ)Very high (gate current ≈ 0)খুব বেশি (gate current ≈ 0)
Gain (gm for same current)Gain (একই current-এ gm)HigherবেশিLowerকম
Size / densitySize / densityLargerবড়Very small, billions per chipখুব ছোট, এক chip-এ billion
Power in logicLogic-এ powerHigher (base current always flows when ON)বেশি (ON থাকলে base current সবসময় চলে)Very low (CMOS)খুব কম (CMOS)
TemperatureTemperatureRisk of thermal runawayThermal runaway-এর ঝুঁকিMore stable (current falls when hot)বেশি stable (গরমে current কমে)
Typical useসাধারণ ব্যবহারAnalog amplifiers, RF, old TTL logicAnalog amplifier, RF, পুরনো TTL logicCPUs, memory (SRAM/DRAM/Flash), power switchesCPU, memory (SRAM/DRAM/Flash), power switch
MCQ trap: The MOSFET input (gate) current is ≈ 0 because the gate is insulated by SiO₂. So it has the highest input impedance of all transistors. The downside: the thin oxide can be destroyed by static electricity (ESD), so MOS chips need careful handling.
MCQ trap: MOSFET-এর input (gate) current ≈ 0, কারণ gate SiO₂ দিয়ে insulated। তাই সব transistor-এর মধ্যে এর input impedance সবচেয়ে বেশি। অসুবিধা: পাতলা oxide static electricity (ESD)-তে নষ্ট হয়ে যেতে পারে, তাই MOS chip সাবধানে ধরতে হয়।

CMOS InverterCMOS Inverter

CMOS = Complementary MOS. It pairs a pMOS (pull-up, connected to VDD) with an nMOS (pull-down, connected to ground). Both gates are tied together as the input. Both drains are tied together as the output.

CMOS = Complementary MOS। এখানে একটা pMOS (pull-up, VDD-তে যুক্ত) আর একটা nMOS (pull-down, ground-এ যুক্ত) জোড়া দেওয়া হয়। দুইটার gate একসাথে জুড়ে input। দুইটার drain একসাথে জুড়ে output।

n-channel enhancement MOSFET GDS broken channel line = enhancement (normally OFF) body CMOS inverter VDD pMOS (pull-up) nMOS (pull-down) Vin Vout GND bubble on gate = pMOS (ON when gate is LOW)
Left: n-channel enhancement MOSFET symbol (the arrow on the body points in for n-channel). Right: CMOS inverter — pMOS on top, nMOS at the bottom, gates joined as input, drains joined as output.বামে: n-channel enhancement MOSFET symbol (n-channel-এ body-র arrow ভেতরের দিকে)। ডানে: CMOS inverter — উপরে pMOS, নিচে nMOS, gate জুড়ে input, drain জুড়ে output।
VinpMOSnMOSVoutPath VDD → GND?VDD → GND path?
0 (LOW)ONOFFVDD (1)No (nMOS OFF)না (nMOS OFF)
VDD (HIGH)OFFON0 (0)No (pMOS OFF)না (pMOS OFF)

Why does CMOS use almost no static power? In either steady state, one transistor is always OFF. So there is never a DC path from VDD to ground. Only a tiny leakage current flows. Power is used mainly when the output switches, to charge and discharge the load capacitance:

CMOS কেন প্রায় কোনো static power খরচ করে না? যেকোনো steady state-এ একটা transistor সবসময় OFF থাকে। তাই VDD থেকে ground পর্যন্ত কখনো DC path থাকে না। শুধু খুব ছোট leakage current চলে। Power খরচ হয় মূলত output যখন switch করে, তখন load capacitance charge আর discharge করতে:

\[ P_{dynamic} = \alpha\, C_L\, V_{DD}^2\, f \qquad (\alpha = \text{activity factor, fraction of cycles that switch}) \]
Example: A CMOS circuit has total switched capacitance C = 50 pF, VDD = 5 V, f = 10 MHz, α = 1. Find the dynamic power. How much power is saved if VDD is reduced to 3.3 V?

P = 50 × 10⁻¹² × 5² × 10 × 10⁶ = 50 × 10⁻¹² × 25 × 10⁷ = 12.5 mW.

Power ∝ VDD². New/old = (3.3/5)² = 0.4356. So power falls to about 44% → about 56% saved. This is why CPU voltages keep going down (5 V → 3.3 V → ~1 V).

Example: একটা CMOS circuit-এর মোট switched capacitance C = 50 pF, VDD = 5 V, f = 10 MHz, α = 1। Dynamic power বের করো। VDD 3.3 V করলে কত power বাঁচে?

P = 50 × 10⁻¹² × 5² × 10 × 10⁶ = 50 × 10⁻¹² × 25 × 10⁷ = 12.5 mW।

Power ∝ VDD²। নতুন/পুরনো = (3.3/5)² = 0.4356। তাই power কমে প্রায় 44% হয় → প্রায় 56% বাঁচে। এজন্যই CPU voltage কমতেই থাকে (5 V → 3.3 V → ~1 V)।

Link to Digital Logic (Chapter 12): Every gate you studied is built from CMOS. NOT = 2 transistors. NAND = 4 (2 nMOS in series + 2 pMOS in parallel). NOR = 4 (2 nMOS in parallel + 2 pMOS in series). AND = NAND + NOT = 6. That is why NAND and NOR are the "natural" universal gates in CMOS. See Digital Logic Design.
Digital Logic (Chapter 12)-এর সাথে সংযোগ: তুমি যে gate গুলো পড়েছ, সবগুলো CMOS দিয়ে বানানো। NOT = 2টা transistor। NAND = 4টা (2টা nMOS series-এ + 2টা pMOS parallel-এ)। NOR = 4টা (2টা nMOS parallel-এ + 2টা pMOS series-এ)। AND = NAND + NOT = 6টা। এজন্যই CMOS-এ NAND আর NOR হলো "স্বাভাবিক" universal gate। দেখো Digital Logic Design।

7. Op-Amp Basics7. Op-Amp Basics

An operational amplifier (op-amp) is an IC amplifier with two inputs and one output. The inputs are the inverting input (−) and the non-inverting input (+). It amplifies the difference between them:

Operational amplifier (op-amp) হলো দুইটা input আর একটা output-ওয়ালা একটা IC amplifier। Input দুইটা হলো inverting input (−) আর non-inverting input (+)। এটা এদের পার্থক্য-কে amplify করে:

\[ V_{out} = A_{OL}\,(V_+ - V_-) \]

AOL is the open-loop gain. It is huge (about 2 × 10⁵ for the classic 741). Because it is so huge, we almost always use negative feedback (a resistor from output back to the − input) to get a small, exact gain set only by resistors.

AOL হলো open-loop gain। এটা বিশাল (classic 741-এ প্রায় 2 × 10⁵)। এত বড় বলে আমরা প্রায় সবসময় negative feedback (output থেকে − input-এ একটা resistor) ব্যবহার করি, যাতে শুধু resistor দিয়ে ঠিক করা একটা ছোট আর নিখুঁত gain পাই।

Ideal Op-Amp PropertiesIdeal Op-Amp-এর বৈশিষ্ট্য

PropertyPropertyIdealReal 741 (typical)আসল 741 (typical)
Open-loop gain AOLOpen-loop gain AOL∞2 × 10⁵
Input impedanceInput impedance∞2 MΩ
Output impedanceOutput impedance075 Ω
BandwidthBandwidth∞≈ 1 MHz gain-bandwidth≈ 1 MHz gain-bandwidth
CMRR∞90 dB
Slew rateSlew rate∞0.5 V/µs

With negative feedback, two golden rules solve almost every op-amp circuit:

  1. No current flows into the inputs (because input impedance is ∞).
  2. V+ = V− (the output adjusts itself until the difference is ~0). This is called the virtual short. If the + input is grounded, the − input is also at 0 V — a virtual ground. "Virtual" because no real wire joins them and no current flows between them.

Negative feedback থাকলে দুইটা golden rule দিয়ে প্রায় সব op-amp circuit solve হয়:

  1. Input-এ কোনো current ঢোকে না (কারণ input impedance ∞)।
  2. V+ = V− (output নিজেকে adjust করে যতক্ষণ না পার্থক্য ~0 হয়)। একে বলে virtual short। + input ground করা থাকলে − input-ও 0 V-এ থাকে — একে বলে virtual ground। "Virtual" কারণ এদের মধ্যে কোনো আসল তার নেই, আর কোনো current-ও চলে না।
Inverting amplifier −+ Vin Rin Rf Vout 0 V (virtual ground) Vout = −(Rf/Rin) Vin Non-inverting amplifier −+ Rin Rf Vin Vout Vout = (1 + Rf/Rin) Vin
Left: inverting amplifier (+ input grounded, − input is a virtual ground). Right: non-inverting amplifier (signal goes to the + input). In both, Rf gives negative feedback to the − input.বামে: inverting amplifier (+ input ground করা, − input virtual ground)। ডানে: non-inverting amplifier (signal যায় + input-এ)। দুইটাতেই Rf − input-এ negative feedback দেয়।

Inverting AmplifierInverting Amplifier

Derivation with the golden rules: V− = V+ = 0 (virtual ground). Current through Rin: I = Vin/Rin. No current enters the op-amp, so the same I goes through Rf: I = (0 − Vout)/Rf. Set equal:

Golden rule দিয়ে derivation: V− = V+ = 0 (virtual ground)। Rin-এর current: I = Vin/Rin। Op-amp-এ কোনো current ঢোকে না, তাই একই I যায় Rf দিয়ে: I = (0 − Vout)/Rf। সমান করি:

\[ A_v = \frac{V_{out}}{V_{in}} = -\frac{R_f}{R_{in}}, \qquad \text{input impedance} = R_{in} \]
Example: Rin = 10 kΩ, Rf = 100 kΩ, Vin = 0.5 V DC. Supply ±15 V. Find Vout. What if Vin = 2 V?

Av = −100/10 = −10. Vout = −10 × 0.5 = −5 V.

Vin = 2 V → ideal answer −20 V. But the output cannot go past the supply. It saturates near −15 V (a real op-amp stops about 1–2 V before the rail, around −13 to −14 V).

Example: Rin = 10 kΩ, Rf = 100 kΩ, Vin = 0.5 V DC। Supply ±15 V। Vout বের করো। Vin = 2 V হলে কী হবে?

Av = −100/10 = −10। Vout = −10 × 0.5 = −5 V।

Vin = 2 V → ideal উত্তর −20 V। কিন্তু output supply-এর বাইরে যেতে পারে না। এটা −15 V-এর কাছে saturate করে (আসল op-amp rail-এর প্রায় 1–2 V আগে থেমে যায়, প্রায় −13 থেকে −14 V)।

Non-Inverting Amplifier and Voltage FollowerNon-Inverting Amplifier আর Voltage Follower

V+ = Vin, so V− = Vin too. Rin and Rf form a divider from Vout: V− = Vout × Rin/(Rin + Rf). Solve:

V+ = Vin, তাই V−-ও = Vin। Rin আর Rf Vout থেকে একটা divider বানায়: V− = Vout × Rin/(Rin + Rf)। Solve করি:

\[ A_v = 1 + \frac{R_f}{R_{in}} \quad (\text{always} \ge 1, \text{ no phase inversion, very high input impedance}) \]
Example: Rin = 10 kΩ, Rf = 90 kΩ, Vin = 0.3 V. Find Vout.

Av = 1 + 90/10 = 10. Vout = 10 × 0.3 = 3 V (same sign as input).

Example: Rin = 10 kΩ, Rf = 90 kΩ, Vin = 0.3 V। Vout বের করো।

Av = 1 + 90/10 = 10। Vout = 10 × 0.3 = 3 V (input-এর একই sign)।

Voltage follower (buffer): connect the output directly to the − input (Rf = 0) and remove Rin (Rin = ∞). Gain = 1 + 0 = 1. Vout = Vin. Why use it? It has very high input impedance and very low output impedance, so it can drive a heavy load without loading the source — like the BJT emitter follower (CC), but better.

Voltage follower (buffer): output সরাসরি − input-এ জোড়া দাও (Rf = 0) আর Rin সরিয়ে দাও (Rin = ∞)। Gain = 1 + 0 = 1। Vout = Vin। কেন ব্যবহার করি? এর input impedance অনেক বেশি আর output impedance অনেক কম, তাই source-এর উপর চাপ না দিয়েই ভারী load চালাতে পারে — BJT emitter follower (CC)-এর মতো, কিন্তু আরও ভালো।

Summing AmplifierSumming Amplifier

Several inputs, each through its own resistor, go into the virtual-ground node of an inverting amplifier. Their currents add up in Rf:

কয়েকটা input, প্রতিটা নিজের resistor দিয়ে, inverting amplifier-এর virtual-ground node-এ যায়। এদের current Rf-এ যোগ হয়:

\[ V_{out} = -R_f\left(\frac{V_1}{R_1} + \frac{V_2}{R_2} + \frac{V_3}{R_3}\right) \]
Example: Rf = R1 = R2 = R3 = 10 kΩ. V1 = 1 V, V2 = 2 V, V3 = −0.5 V. Find Vout.

All resistors are equal, so Vout = −(V1 + V2 + V3) = −(1 + 2 − 0.5) = −2.5 V.

If we use binary-weighted resistors (R, 2R, 4R, 8R) for the bits of a number, the summing amplifier becomes a simple DAC (digital-to-analog converter). See practice Q20.

Example: Rf = R1 = R2 = R3 = 10 kΩ। V1 = 1 V, V2 = 2 V, V3 = −0.5 V। Vout বের করো।

সব resistor সমান, তাই Vout = −(V1 + V2 + V3) = −(1 + 2 − 0.5) = −2.5 V।

একটা সংখ্যার bit গুলোর জন্য binary-weighted resistor (R, 2R, 4R, 8R) ব্যবহার করলে summing amplifier একটা সহজ DAC (digital-to-analog converter) হয়ে যায়। Practice Q20 দেখো।

Difference Amplifier, Integrator, Differentiator, ComparatorDifference Amplifier, Integrator, Differentiator, Comparator

  • Difference amplifier: with matched resistors, Vout = (Rf/R1)(V2 − V1). Example: Rf/R1 = 10, V2 = 2.5 V, V1 = 2.0 V → Vout = 10 × 0.5 = 5 V. Used to measure small sensor differences.
  • Integrator: put a capacitor C in place of Rf. Vout = −(1/RC)∫Vin dt. A square wave in → a triangle wave out. Example: R = 10 kΩ, C = 1 µF (RC = 10 ms), Vin = 1 V DC for 5 ms → Vout = −(1/0.01) × 1 × 0.005 = −0.5 V (a ramp falling at 100 V/s).
  • Differentiator: put C in place of Rin. Vout = −RC (dVin/dt). A triangle wave in → a square wave out.
  • Comparator: no feedback (open loop). The huge gain drives the output to a rail: Vout = +Vsat if V+ > V−, else −Vsat. Example: Vref = 2 V on the − input, Vin = 2.1 V on the + input → output = +Vsat. It works like a 1-bit ADC. Here the golden rule V+ = V− does not apply (no negative feedback).
  • Difference amplifier: matched resistor হলে Vout = (Rf/R1)(V2 − V1)। Example: Rf/R1 = 10, V2 = 2.5 V, V1 = 2.0 V → Vout = 10 × 0.5 = 5 V। Sensor-এর ছোট পার্থক্য মাপতে ব্যবহার হয়।
  • Integrator: Rf-এর জায়গায় একটা capacitor C বসাও। Vout = −(1/RC)∫Vin dt। Square wave দিলে → triangle wave বের হয়। Example: R = 10 kΩ, C = 1 µF (RC = 10 ms), 5 ms ধরে Vin = 1 V DC → Vout = −(1/0.01) × 1 × 0.005 = −0.5 V (100 V/s হারে নামতে থাকা একটা ramp)।
  • Differentiator: Rin-এর জায়গায় C বসাও। Vout = −RC (dVin/dt)। Triangle wave দিলে → square wave বের হয়।
  • Comparator: কোনো feedback নেই (open loop)। বিশাল gain output-কে একটা rail-এ ঠেলে দেয়: V+ > V− হলে Vout = +Vsat, না হলে −Vsat। Example: − input-এ Vref = 2 V, + input-এ Vin = 2.1 V → output = +Vsat। এটা 1-bit ADC-এর মতো কাজ করে। এখানে golden rule V+ = V− খাটে না (negative feedback নেই)।
CircuitOutput formulaOutput formulaRememberমনে রাখো
Inverting−(Rf/Rin)Vin180° phase shift, gain can be < 1180° phase shift, gain 1-এর কমও হতে পারে
Non-inverting(1 + Rf/Rin)VinIn phase, gain ≥ 1একই phase, gain ≥ 1
Voltage followerVinBuffer, gain = 1Buffer, gain = 1
Summing−RfΣVi/RiAdder, audio mixer, DACAdder, audio mixer, DAC
Integrator−(1/RC)∫VindtSquare → triangleSquare → triangle
Differentiator−RC dVin/dtTriangle → squareTriangle → square
Comparator±VsatNo feedback; 1-bit ADCFeedback নেই; 1-bit ADC
Exam tips: (1) An ideal op-amp has infinite gain and input impedance and zero output impedance — MCQs often swap these. (2) Virtual short needs negative feedback. (3) The output can never go beyond the supply rails — always check for saturation. (4) CMRR = differential gain / common-mode gain; ideal = ∞.
Exam tips: (1) Ideal op-amp-এর gain আর input impedance infinite, output impedance zero — MCQ-তে প্রায়ই এগুলো উল্টে দেয়। (2) Virtual short-এর জন্য negative feedback লাগে। (3) Output কখনো supply rail-এর বাইরে যেতে পারে না — সবসময় saturation check করো। (4) CMRR = differential gain / common-mode gain; ideal = ∞।

Practice Questions (Admission Style)Practice Questions (Admission Style)

20 questions, easy → hard. Q1–Q12 are IICT MCQ style (aim for under 1 minute each). Q13–Q20 are IICT written style — show every step, units and a region/state check, as the examiner gives marks for steps.

20টা প্রশ্ন, সহজ → কঠিন। Q1–Q12 হলো IICT MCQ style (প্রতিটা 1 মিনিটের কম সময়ে করার চেষ্টা করো)। Q13–Q20 হলো IICT written style — প্রতিটা step, unit আর region/state check দেখাও, কারণ examiner step-এর জন্য নম্বর দেন।

Q1. [IICT MCQ style] The majority carriers in an n-type semiconductor are:
  • (a) Holes
  • (b) Free electrons
  • (c) Positive donor ions
  • (d) Negative acceptor ions
Q1. [IICT MCQ style] n-type semiconductor-এ majority carrier হলো:
  • (a) Hole
  • (b) Free electron
  • (c) Positive donor ion
  • (d) Negative acceptor ion
Show Answerউত্তর দেখুন
Answer: (b) — A pentavalent donor gives one extra free electron per atom, so electrons are the majority. Donor ions are fixed in the crystal and cannot move, so they are not carriers at all. Holes are the minority.
Answer: (b) — Pentavalent donor প্রতি atom-এ একটা বাড়তি free electron দেয়, তাই electron majority। Donor ion crystal-এ স্থির, চলতে পারে না, তাই এরা carrier-ই না। Hole হলো minority।
Q2. [IICT MCQ style] The band gap of silicon at room temperature is about:
  • (a) 0.67 eV
  • (b) 1.1 eV
  • (c) 1.43 eV
  • (d) 5.5 eV
Q2. [IICT MCQ style] Room temperature-এ silicon-এর band gap প্রায়:
  • (a) 0.67 eV
  • (b) 1.1 eV
  • (c) 1.43 eV
  • (d) 5.5 eV
Show Answerউত্তর দেখুন
Answer: (b) — Si = 1.1 eV. The other options are traps: 0.67 eV is Ge, 1.43 eV is GaAs, and 5.5 eV is diamond (an insulator).
Answer: (b) — Si = 1.1 eV। অন্য option গুলো trap: 0.67 eV হলো Ge, 1.43 eV হলো GaAs, আর 5.5 eV হলো diamond (একটা insulator)।
Q3. [IICT MCQ style] Which impurity added to pure silicon makes a p-type semiconductor?
  • (a) Phosphorus
  • (b) Arsenic
  • (c) Boron
  • (d) Antimony
Q3. [IICT MCQ style] Pure silicon-এ কোন impurity মেশালে p-type semiconductor হয়?
  • (a) Phosphorus
  • (b) Arsenic
  • (c) Boron
  • (d) Antimony
Show Answerউত্তর দেখুন
Answer: (c) — Boron is trivalent (3 valence electrons). It leaves one bond incomplete, which is a hole, so it is an acceptor and makes p-type. P, As and Sb are all pentavalent donors (n-type).
Answer: (c) — Boron trivalent (3টা valence electron)। এটা একটা bond অসম্পূর্ণ রাখে, যেটা একটা hole, তাই এটা acceptor আর p-type বানায়। P, As আর Sb সবগুলো pentavalent donor (n-type)।
Q4. [IICT MCQ style] The reverse saturation current of a PN junction diode is mainly due to:
  • (a) Majority carriers
  • (b) Minority carriers
  • (c) Fixed donor and acceptor ions
  • (d) Avalanche multiplication
Q4. [IICT MCQ style] একটা PN junction diode-এর reverse saturation current মূলত কীসের কারণে?
  • (a) Majority carrier
  • (b) Minority carrier
  • (c) স্থির donor আর acceptor ion
  • (d) Avalanche multiplication
Show Answerউত্তর দেখুন
Answer: (b) — In reverse bias, the barrier stops majority carriers. But the junction field happily sweeps across the few minority carriers (holes in n, electrons in p) made by heat. That tiny flow is Is. Because heat makes these carriers, Is roughly doubles every 10 °C. Avalanche only happens at breakdown, not in normal reverse bias.
Answer: (b) — Reverse bias-এ barrier majority carrier আটকে দেয়। কিন্তু তাপ থেকে তৈরি অল্প কিছু minority carrier (n-এ hole, p-তে electron)-কে junction field সহজেই পার করে দেয়। ওই ছোট flow-টাই Is। তাপ এই carrier বানায় বলে প্রতি 10 °C-এ Is প্রায় দ্বিগুণ হয়। Avalanche শুধু breakdown-এ হয়, সাধারণ reverse bias-এ না।
Q5. [IICT MCQ style] A BJT is in the saturation region when:
  • (a) BE forward biased, BC reverse biased
  • (b) BE reverse biased, BC reverse biased
  • (c) BE forward biased, BC forward biased
  • (d) BE reverse biased, BC forward biased
Q5. [IICT MCQ style] একটা BJT saturation region-এ থাকে যখন:
  • (a) BE forward biased, BC reverse biased
  • (b) BE reverse biased, BC reverse biased
  • (c) BE forward biased, BC forward biased
  • (d) BE reverse biased, BC forward biased
Show Answerউত্তর দেখুন
Answer: (c) — Saturation = both junctions forward (F-F); VCE drops to about 0.2 V and the BJT acts as a closed switch. (a) is active (amplifier), (b) is cutoff (open switch), (d) is reverse active.
Answer: (c) — Saturation = দুইটা junction-ই forward (F-F); VCE প্রায় 0.2 V-এ নামে আর BJT বন্ধ switch-এর মতো কাজ করে। (a) হলো active (amplifier), (b) cutoff (খোলা switch), (d) reverse active।
Q6. [IICT MCQ style] In a bridge rectifier with peak secondary voltage Vm (ideal diodes), the peak inverse voltage across each diode is:
  • (a) Vm/2
  • (b) Vm
  • (c) 2Vm
  • (d) √2 Vm
Q6. [IICT MCQ style] একটা bridge rectifier-এ secondary-র peak voltage Vm (ideal diode) হলে প্রতিটা diode-এর peak inverse voltage হলো:
  • (a) Vm/2
  • (b) Vm
  • (c) 2Vm
  • (d) √2 Vm
Show Answerউত্তর দেখুন
Answer: (b) — In each half cycle, the two OFF diodes sit across the secondary together with the ON diodes (which have ~0 V), so each OFF diode sees only Vm. The trap answer 2Vm is for the center-tap rectifier, where the OFF diode sees the whole secondary.
Answer: (b) — প্রতি half cycle-এ OFF diode দুইটা ON diode (যাদের ~0 V) সহ secondary-র across-এ থাকে, তাই প্রতিটা OFF diode শুধু Vm দেখে। Trap উত্তর 2Vm হলো center-tap rectifier-এর, যেখানে OFF diode পুরো secondary দেখে।
Q7. [IICT MCQ style] A transistor has α = 0.99. Its β is:
  • (a) 0.99
  • (b) 9.9
  • (c) 99
  • (d) 100
Q7. [IICT MCQ style] একটা transistor-এর α = 0.99। এর β হলো:
  • (a) 0.99
  • (b) 9.9
  • (c) 99
  • (d) 100
Show Answerউত্তর দেখুন
Answer: (c) — β = α/(1 − α) = 0.99/0.01 = 99. Check backwards: α = 99/100 = 0.99 ✓. (100 would need α = 100/101 = 0.990099…)
Answer: (c) — β = α/(1 − α) = 0.99/0.01 = 99। উল্টো দিক থেকে check: α = 99/100 = 0.99 ✓। (100 হতে হলে α = 100/101 = 0.990099… লাগত)
Q8. [IICT MCQ style] A half-wave rectifier (ideal diode) is fed with a sine wave of peak 31.4 V. The average (DC) output voltage is about:
  • (a) 10 V
  • (b) 15.7 V
  • (c) 20 V
  • (d) 22.2 V
Q8. [IICT MCQ style] একটা half-wave rectifier (ideal diode)-এ 31.4 V peak-এর sine wave দেওয়া হলো। Average (DC) output voltage প্রায়:
  • (a) 10 V
  • (b) 15.7 V
  • (c) 20 V
  • (d) 22.2 V
Show Answerউত্তর দেখুন
Answer: (a) — Vdc = Vm/π = 31.4/3.1416 ≈ 10 V. Traps: 15.7 V = Vm/2 (that is the half-wave rms), 20 V = 2Vm/π (full-wave), 22.2 V = Vm/√2 (full-wave rms).
Answer: (a) — Vdc = Vm/π = 31.4/3.1416 ≈ 10 V। Trap: 15.7 V = Vm/2 (এটা half-wave rms), 20 V = 2Vm/π (full-wave), 22.2 V = Vm/√2 (full-wave rms)।
Q9. [IICT MCQ style] The input (gate) current of a MOSFET is almost zero because:
  • (a) The base is very thin
  • (b) The gate is insulated from the channel by a thin SiO₂ layer
  • (c) The source is heavily doped
  • (d) The drain junction is reverse biased
Q9. [IICT MCQ style] MOSFET-এর input (gate) current প্রায় শূন্য, কারণ:
  • (a) Base খুব পাতলা
  • (b) একটা পাতলা SiO₂ layer দিয়ে gate channel থেকে insulated
  • (c) Source heavily doped
  • (d) Drain junction reverse biased
Show Answerউত্তর দেখুন
Answer: (b) — The "O" in MOS is the oxide, an insulator. The gate works like one plate of a capacitor, so no DC current flows into it. This gives an input impedance of 10¹⁰ Ω or more. (a) is about BJTs; MOSFETs have no base.
Answer: (b) — MOS-এর "O" হলো oxide, একটা insulator। Gate একটা capacitor-এর এক plate-এর মতো কাজ করে, তাই এতে কোনো DC current ঢোকে না। এতে input impedance 10¹⁰ Ω বা তার বেশি হয়। (a) BJT-এর কথা; MOSFET-এ কোনো base নেই।
Q10. [IICT MCQ style] Silicon with ni = 1.5 × 10¹⁰ cm⁻³ is doped with 10¹⁷ donors/cm³. The hole concentration is:
  • (a) 1.5 × 10¹⁰ cm⁻³
  • (b) 2.25 × 10³ cm⁻³
  • (c) 2.25 × 10⁵ cm⁻³
  • (d) 10¹⁷ cm⁻³
Q10. [IICT MCQ style] ni = 1.5 × 10¹⁰ cm⁻³ -এর silicon-কে 10¹⁷ donors/cm³ দিয়ে dope করা হলো। Hole concentration হলো:
  • (a) 1.5 × 10¹⁰ cm⁻³
  • (b) 2.25 × 10³ cm⁻³
  • (c) 2.25 × 10⁵ cm⁻³
  • (d) 10¹⁷ cm⁻³
Show Answerউত্তর দেখুন
Answer: (b) — n ≈ ND = 10¹⁷. Mass-action law: p = ni²/n = (2.25 × 10²⁰)/10¹⁷ = 2.25 × 10³ cm⁻³. Doping with donors reduces holes far below ni. (c) is the answer for 10¹⁵ doping.
Answer: (b) — n ≈ ND = 10¹⁷। Mass-action law: p = ni²/n = (2.25 × 10²⁰)/10¹⁷ = 2.25 × 10³ cm⁻³। Donor দিয়ে doping করলে hole ni-এর অনেক নিচে কমে যায়। (c) হলো 10¹⁵ doping-এর উত্তর।
Q11. [IICT MCQ style] A CMOS inverter uses almost no static (DC) power because:
  • (a) Both transistors are always ON
  • (b) In either steady state one transistor is OFF, so there is no DC path from VDD to ground
  • (c) The gate current is very large
  • (d) It only works at low frequency
Q11. [IICT MCQ style] একটা CMOS inverter প্রায় কোনো static (DC) power খরচ করে না, কারণ:
  • (a) দুইটা transistor সবসময় ON
  • (b) যেকোনো steady state-এ একটা transistor OFF, তাই VDD থেকে ground পর্যন্ত কোনো DC path নেই
  • (c) Gate current অনেক বড়
  • (d) এটা শুধু low frequency-তে কাজ করে
Show Answerউত্তর দেখুন
Answer: (b) — Input LOW → pMOS ON, nMOS OFF. Input HIGH → nMOS ON, pMOS OFF. Always one is OFF, so only leakage flows. Power is used mainly while switching: P = αCVDD²f. If both were ON (a), there would be a short from VDD to ground — this only happens briefly during a transition.
Answer: (b) — Input LOW → pMOS ON, nMOS OFF। Input HIGH → nMOS ON, pMOS OFF। সবসময় একটা OFF, তাই শুধু leakage চলে। Power খরচ হয় মূলত switching-এর সময়: P = αCVDD²f। দুইটাই ON হলে (a) VDD থেকে ground-এ short হতো — এটা শুধু transition-এর সময় খুব অল্প সময়ের জন্য হয়।
Q12. [IICT MCQ style] A non-inverting amplifier has Rf = 90 kΩ and Rin = 10 kΩ, with ±12 V supplies. For Vin = 1.5 V DC, the output is:
  • (a) +13.5 V
  • (b) +15 V
  • (c) About +12 V or a little less (positive saturation)
  • (d) −15 V
Q12. [IICT MCQ style] একটা non-inverting amplifier-এ Rf = 90 kΩ আর Rin = 10 kΩ, supply ±12 V। Vin = 1.5 V DC হলে output হবে:
  • (a) +13.5 V
  • (b) +15 V
  • (c) প্রায় +12 V বা একটু কম (positive saturation)
  • (d) −15 V
Show Answerউত্তর দেখুন
Answer: (c) — Gain = 1 + 90/10 = 10, so the ideal output is 15 V. But the output cannot go above the +12 V rail, so it saturates near +12 V (a real op-amp gives about +10.5 to +11 V). (b) forgets saturation; (a) uses the wrong gain Rf/Rin = 9; (d) has the wrong sign — a non-inverting amplifier does not invert.
Answer: (c) — Gain = 1 + 90/10 = 10, তাই ideal output 15 V। কিন্তু output +12 V rail-এর উপরে যেতে পারে না, তাই এটা +12 V-এর কাছে saturate করে (আসল op-amp প্রায় +10.5 থেকে +11 V দেয়)। (b) saturation ভুলে গেছে; (a) ভুল gain Rf/Rin = 9 নিয়েছে; (d)-এর sign ভুল — non-inverting amplifier invert করে না।
Q13. [IICT written style] A 12 V DC source, a 2.2 kΩ resistor and a forward-biased Si diode are connected in series. (a) Find the current using the ideal model. (b) Find the current using the constant-drop model. (c) Find the power used by the diode in (b). (d) A second identical Si diode is added in series. Find the new current.
Q13. [IICT written style] একটা 12 V DC source, একটা 2.2 kΩ resistor আর একটা forward-biased Si diode series-এ যুক্ত। (a) Ideal model দিয়ে current বের করো। (b) Constant-drop model দিয়ে current বের করো। (c) (b)-তে diode কত power খরচ করে? (d) আরেকটা একই রকম Si diode series-এ যোগ করা হলো। নতুন current কত?
Show Answerউত্তর দেখুন

(a) Ideal diode = short: I = 12/2.2 kΩ = 5.45 mA.

(b) KVL: 12 = 0.7 + I(2.2 kΩ) → I = 11.3/2.2 kΩ = 5.14 mA.

(c) PD = VD × I = 0.7 × 5.14 mA = 3.6 mW.

(d) Two drops: I = (12 − 1.4)/2.2 kΩ = 10.6/2.2 = 4.82 mA.

Why: in series, diode drops add just like batteries opposing the source.

(a) Ideal diode = short: I = 12/2.2 kΩ = 5.45 mA।

(b) KVL: 12 = 0.7 + I(2.2 kΩ) → I = 11.3/2.2 kΩ = 5.14 mA।

(c) PD = VD × I = 0.7 × 5.14 mA = 3.6 mW।

(d) দুইটা drop: I = (12 − 1.4)/2.2 kΩ = 10.6/2.2 = 4.82 mA।

কারণ: series-এ diode drop গুলো source-এর বিপরীতে রাখা battery-র মতো যোগ হয়।

Q14. [IICT written style] A bridge rectifier with Si diodes is fed from a transformer secondary of 12 V rms, 50 Hz. Find: (a) the peak secondary voltage, (b) the peak output voltage, (c) the DC output voltage (no filter), (d) the PIV rating needed for each diode, (e) the ripple frequency.
Q14. [IICT written style] Si diode-ওয়ালা একটা bridge rectifier-কে 12 V rms, 50 Hz-এর transformer secondary থেকে দেওয়া হলো। বের করো: (a) peak secondary voltage, (b) peak output voltage, (c) DC output voltage (filter ছাড়া), (d) প্রতিটা diode-এর দরকারি PIV rating, (e) ripple frequency।
Show Answerউত্তর দেখুন

(a) Vm = √2 × 12 = 16.97 V.

(b) Two diodes conduct in series: Vout(peak) = 16.97 − 1.4 = 15.57 V.

(c) Vdc = 2 × 15.57/π = 9.91 V.

(d) PIV ≈ Vm − 0.7 = 16.27 V (≈ 17 V with ideal diodes). Choose diodes rated well above this, for example 50 V (1N4001).

(e) Full-wave → 2 × 50 = 100 Hz.

(a) Vm = √2 × 12 = 16.97 V।

(b) দুইটা diode series-এ conduct করে: Vout(peak) = 16.97 − 1.4 = 15.57 V।

(c) Vdc = 2 × 15.57/π = 9.91 V।

(d) PIV ≈ Vm − 0.7 = 16.27 V (ideal diode-এ ≈ 17 V)। এর চেয়ে অনেক বেশি rating-এর diode নাও, যেমন 50 V (1N4001)।

(e) Full-wave → 2 × 50 = 100 Hz।

Q15. [IICT written style] A full-wave rectifier on 50 Hz mains gives a peak of 15 V to a 500 Ω load. Find the minimum filter capacitor so that the peak-to-peak ripple is at most 1 V. Find the approximate DC output and load current. What capacitor would a half-wave rectifier need for the same ripple?
Q15. [IICT written style] 50 Hz mains-এ একটা full-wave rectifier একটা 500 Ω load-কে 15 V peak দেয়। Peak-to-peak ripple সর্বোচ্চ 1 V রাখতে minimum filter capacitor কত লাগবে? আনুমানিক DC output আর load current বের করো। একই ripple-এর জন্য half-wave rectifier-এ কত capacitor লাগত?
Show Answerউত্তর দেখুন

Full-wave → ripple frequency f = 100 Hz. From Vr = Vm/(fRC):

C = Vm/(f R Vr) = 15/(100 × 500 × 1) = 3 × 10⁻⁴ F = 300 µF (use the next standard value, 330 µF).

Vdc ≈ Vm − Vr/2 = 15 − 0.5 = 14.5 V. Idc = 14.5/500 = 29 mA.

Half-wave → f = 50 Hz → C = 15/(50 × 500 × 1) = 600 µF (double).

Full-wave → ripple frequency f = 100 Hz। Vr = Vm/(fRC) থেকে:

C = Vm/(f R Vr) = 15/(100 × 500 × 1) = 3 × 10⁻⁴ F = 300 µF (পরের standard value 330 µF নাও)।

Vdc ≈ Vm − Vr/2 = 15 − 0.5 = 14.5 V। Idc = 14.5/500 = 29 mA।

Half-wave → f = 50 Hz → C = 15/(50 × 500 × 1) = 600 µF (দ্বিগুণ)।

Q16. [IICT written style] A Zener regulator has Vin = 24 V, VZ = 12 V and series R = 470 Ω. The load RL changes from 1 kΩ to 3 kΩ. (a) Find the range of Zener current. (b) Find the smallest RL that still keeps regulation (take IZ(min) ≈ 0). (c) What Zener power rating is needed if the load may be removed completely?
Q16. [IICT written style] একটা Zener regulator-এ Vin = 24 V, VZ = 12 V আর series R = 470 Ω। Load RL 1 kΩ থেকে 3 kΩ পর্যন্ত বদলায়। (a) Zener current-এর range বের করো। (b) Regulation বজায় থাকে এমন সবচেয়ে ছোট RL কত (IZ(min) ≈ 0 ধরো)? (c) Load পুরো সরিয়ে ফেলা হতে পারলে Zener-এর কত power rating লাগবে?
Show Answerউত্তর দেখুন

Check ON (worst case RL = 1 kΩ): 24 × 1/(0.47 + 1) = 16.3 V ≥ 12 V ✓ → Vout = 12 V.

IR = (24 − 12)/470 = 25.53 mA (fixed).

(a) RL = 1 kΩ: IL = 12 mA → IZ = 25.53 − 12 = 13.53 mA. RL = 3 kΩ: IL = 4 mA → IZ = 25.53 − 4 = 21.53 mA. So 13.5 mA to 21.5 mA.

(b) RL(min) = R VZ/(Vin − VZ) = 470 × 12/12 = 470 Ω. (Then all 25.53 mA goes to the load and IZ = 0.)

(c) No load → IZ = IR = 25.53 mA → PZ = 12 × 25.53 mA = 306 mW. Choose a 0.5 W Zener. (Within the given 1–3 kΩ range the maximum is only 12 × 21.53 = 258 mW.)

ON কিনা check (worst case RL = 1 kΩ): 24 × 1/(0.47 + 1) = 16.3 V ≥ 12 V ✓ → Vout = 12 V।

IR = (24 − 12)/470 = 25.53 mA (fixed)।

(a) RL = 1 kΩ: IL = 12 mA → IZ = 25.53 − 12 = 13.53 mA। RL = 3 kΩ: IL = 4 mA → IZ = 25.53 − 4 = 21.53 mA। তাই 13.5 mA থেকে 21.5 mA।

(b) RL(min) = R VZ/(Vin − VZ) = 470 × 12/12 = 470 Ω। (তখন পুরো 25.53 mA load-এ যায় আর IZ = 0।)

(c) No load → IZ = IR = 25.53 mA → PZ = 12 × 25.53 mA = 306 mW। 0.5 W Zener নাও। (দেওয়া 1–3 kΩ range-এর মধ্যে সর্বোচ্চ মাত্র 12 × 21.53 = 258 mW।)

Q17. [IICT written style] A fixed-bias npn circuit has VCC = 10 V, RB = 150 kΩ, RC = 1.5 kΩ, β = 120, VBE = 0.7 V, VCE(sat) = 0.2 V. (a) Find the operating region, IC and VCE. (b) What RB would put the Q-point at VCE = 5 V?
Q17. [IICT written style] একটা fixed-bias npn circuit-এ VCC = 10 V, RB = 150 kΩ, RC = 1.5 kΩ, β = 120, VBE = 0.7 V, VCE(sat) = 0.2 V। (a) Operating region, IC আর VCE বের করো। (b) কত RB দিলে Q-point VCE = 5 V-এ থাকবে?
Show Answerউত্তর দেখুন

(a) IB = (10 − 0.7)/150 kΩ = 62 µA.

Assume active: IC = 120 × 62 µA = 7.44 mA → VCE = 10 − 7.44 × 1.5 = −1.16 V. Impossible! So the assumption is wrong: the BJT is saturated.

In saturation: VCE = 0.2 V, IC = (10 − 0.2)/1.5 kΩ = 6.53 mA. Check: IB(min) = 6.53 mA/120 = 54.4 µA < 62 µA ✓.

(b) VCE = 5 V → IC = (10 − 5)/1.5 kΩ = 3.33 mA → IB = 3.33 mA/120 = 27.8 µA → RB = 9.3/27.8 µA = ≈ 335 kΩ (use 330 kΩ).

(a) IB = (10 − 0.7)/150 kΩ = 62 µA।

Active ধরি: IC = 120 × 62 µA = 7.44 mA → VCE = 10 − 7.44 × 1.5 = −1.16 V। অসম্ভব! তাই ধারণা ভুল: BJT saturated।

Saturation-এ: VCE = 0.2 V, IC = (10 − 0.2)/1.5 kΩ = 6.53 mA। Check: IB(min) = 6.53 mA/120 = 54.4 µA < 62 µA ✓।

(b) VCE = 5 V → IC = (10 − 5)/1.5 kΩ = 3.33 mA → IB = 3.33 mA/120 = 27.8 µA → RB = 9.3/27.8 µA = ≈ 335 kΩ (330 kΩ নাও)।

Q18. [IICT written style] A voltage-divider biased npn has VCC = 15 V, R1 = 56 kΩ, R2 = 12 kΩ, RC = 3.3 kΩ, RE = 1.2 kΩ, β = 100, VBE = 0.7 V. Find VB, VE, IC, VC and VCE by the approximate method. Is the approximation good here?
Q18. [IICT written style] একটা voltage-divider biased npn-এ VCC = 15 V, R1 = 56 kΩ, R2 = 12 kΩ, RC = 3.3 kΩ, RE = 1.2 kΩ, β = 100, VBE = 0.7 V। Approximate method দিয়ে VB, VE, IC, VC আর VCE বের করো। এখানে approximation কি ভালো?
Show Answerউত্তর দেখুন

VB = 15 × 12/(56 + 12) = 2.65 V. VE = 2.65 − 0.7 = 1.95 V.

IC ≈ IE = 1.95/1.2 kΩ = 1.62 mA.

VC = 15 − 1.62 × 3.3 = 9.65 V. VCE = VC − VE = 15 − 1.62 × (3.3 + 1.2) = 7.70 V. Active ✓ (VCE ≫ 0.2 V).

Check: βRE = 120 kΩ and 10R2 = 120 kΩ — exactly on the border. So the approximation is only fair. The exact Thevenin method (RTh = 56 ∥ 12 = 9.88 kΩ, IB = (2.65 − 0.7)/(9.88 + 101 × 1.2) kΩ = 14.9 µA) gives IC = 1.49 mA and VCE = 8.30 V — about 9% different. In an exam, give the approximate answer, then mention this check.

VB = 15 × 12/(56 + 12) = 2.65 V। VE = 2.65 − 0.7 = 1.95 V।

IC ≈ IE = 1.95/1.2 kΩ = 1.62 mA।

VC = 15 − 1.62 × 3.3 = 9.65 V। VCE = VC − VE = 15 − 1.62 × (3.3 + 1.2) = 7.70 V। Active ✓ (VCE ≫ 0.2 V)।

Check: βRE = 120 kΩ আর 10R2 = 120 kΩ — ঠিক সীমানায়। তাই approximation মোটামুটি। Exact Thevenin method (RTh = 56 ∥ 12 = 9.88 kΩ, IB = (2.65 − 0.7)/(9.88 + 101 × 1.2) kΩ = 14.9 µA) দিলে IC = 1.49 mA আর VCE = 8.30 V — প্রায় 9% পার্থক্য। Exam-এ approximate উত্তর দাও, তারপর এই check উল্লেখ করো।

Q19. [IICT written style] An enhancement nMOS has Vt = 1.5 V and k = 1 mA/V² (saturation: ID = (k/2)(VGS − Vt)²). It is used with VDD = 10 V and RD = 3 kΩ. (a) For VGS = 3.5 V, find ID and VDS and confirm the region. (b) What is the largest RD that keeps it in saturation? (c) What happens if VGS = 1 V?
Q19. [IICT written style] একটা enhancement nMOS-এর Vt = 1.5 V আর k = 1 mA/V² (saturation: ID = (k/2)(VGS − Vt)²)। এটা VDD = 10 V আর RD = 3 kΩ-এর সাথে ব্যবহার হচ্ছে। (a) VGS = 3.5 V হলে ID আর VDS বের করো আর region নিশ্চিত করো। (b) Saturation-এ রাখে এমন সবচেয়ে বড় RD কত? (c) VGS = 1 V হলে কী হবে?
Show Answerউত্তর দেখুন

(a) Vov = VGS − Vt = 2 V. Assume saturation: ID = (1/2)(2)² = 2 mA. VDS = 10 − 2 × 3 = 4 V. Check: 4 ≥ 2 ✓ → saturation.

(b) Need VDS ≥ 2 V: 10 − 2 mA × RD ≥ 2 → RD ≤ 8/2 mA = 4 kΩ. Above 4 kΩ it enters the triode region.

(c) VGS = 1 V < Vt = 1.5 V → cutoff, ID = 0, VDS = 10 V. (If VGS = 0 → output 10 V; if VGS large → output low: this nMOS + RD is a simple inverter.)

(a) Vov = VGS − Vt = 2 V। Saturation ধরি: ID = (1/2)(2)² = 2 mA। VDS = 10 − 2 × 3 = 4 V। Check: 4 ≥ 2 ✓ → saturation।

(b) দরকার VDS ≥ 2 V: 10 − 2 mA × RD ≥ 2 → RD ≤ 8/2 mA = 4 kΩ। 4 kΩ-এর বেশি হলে এটা triode region-এ চলে যায়।

(c) VGS = 1 V < Vt = 1.5 V → cutoff, ID = 0, VDS = 10 V। (VGS = 0 → output 10 V; VGS বড় → output low: এই nMOS + RD একটা সহজ inverter।)

Q20. [IICT written style] A 4-bit binary-weighted DAC uses an op-amp summing amplifier with Rf = 10 kΩ. The input resistors are 10 kΩ (MSB, b3), 20 kΩ (b2), 40 kΩ (b1) and 80 kΩ (LSB, b0). Logic 1 = 5 V, logic 0 = 0 V. Supply is ±12 V. (a) Find Vout for input 1011. (b) Find the step size (1 LSB). (c) Find the full-scale output (1111). Does the op-amp saturate?
Q20. [IICT written style] একটা 4-bit binary-weighted DAC-এ Rf = 10 kΩ-এর op-amp summing amplifier ব্যবহার হয়েছে। Input resistor গুলো 10 kΩ (MSB, b3), 20 kΩ (b2), 40 kΩ (b1) আর 80 kΩ (LSB, b0)। Logic 1 = 5 V, logic 0 = 0 V। Supply ±12 V। (a) Input 1011 হলে Vout বের করো। (b) Step size (1 LSB) বের করো। (c) Full-scale output (1111) বের করো। Op-amp কি saturate করবে?
Show Answerউত্তর দেখুন

Summing formula: Vout = −Rf(V3/10k + V2/20k + V1/40k + V0/80k).

(a) 1011 → b3 = 1, b2 = 0, b1 = 1, b0 = 1:
Vout = −10k(5/10k + 0 + 5/40k + 5/80k) = −(5 + 0 + 1.25 + 0.625) = −6.875 V.

(b) 1 LSB = 10k × 5/80k = 0.625 V. Check: 1011₂ = 11 → 11 × 0.625 = 6.875 ✓.

(c) 1111 = 15 → −15 × 0.625 = −9.375 V. |−9.375| < 12 V, so the op-amp does not saturate. (The output is negative because this is an inverting summer; add an inverting stage of gain −1 to get positive output.)

Summing formula: Vout = −Rf(V3/10k + V2/20k + V1/40k + V0/80k)।

(a) 1011 → b3 = 1, b2 = 0, b1 = 1, b0 = 1:
Vout = −10k(5/10k + 0 + 5/40k + 5/80k) = −(5 + 0 + 1.25 + 0.625) = −6.875 V।

(b) 1 LSB = 10k × 5/80k = 0.625 V। Check: 1011₂ = 11 → 11 × 0.625 = 6.875 ✓।

(c) 1111 = 15 → −15 × 0.625 = −9.375 V। |−9.375| < 12 V, তাই op-amp saturate করবে না। (Output negative কারণ এটা inverting summer; positive output পেতে gain −1-এর আরেকটা inverting stage যোগ করো।)